Temperature mitigation effect of phase change material on overcharging lithium-ion batteries: an experimental study

2021 ◽  
Author(s):  
Jiahao Liu ◽  
Yining Fan ◽  
Qimiao Xie
Keyword(s):  
Experimental Study ◽  
Phase Change ◽  
Lithium Ion Batteries ◽  
Phase Change Material ◽  
Lithium Ion ◽  
Change Material

scholarly journals Thermal Simulation of Phase Change Material for Cooling of a Lithium-Ion Battery Pack

Electrochem ◽  
2020 ◽  
Vol 1 (4) ◽  
pp. 439-449
Author(s):  
Seyed Saeed Madani ◽  
Erik Schaltz ◽  
Søren Knudsen Kær
Keyword(s):  
Phase Change ◽  
Lithium Ion Batteries ◽  
Lithium Ion Battery ◽  
Phase Change Material ◽  
Thermal Management ◽  
Lithium Ion ◽  
Battery Pack ◽  
Thermal Management System ◽  
Fast Charging ◽  
Change Material

A new heat transfer enhancement approach was proposed for the cooling system of lithium-ion batteries. A three-dimensional numerical simulation of the passive thermal management system for a battery pack was accomplished by employing ANSYS Fluent (Canonsburg, PA, USA). Phase change material was used for the thermal management of lithium-ion battery modules and as the heat transmission source to decrease battery temperature in fast charging and discharge conditions. Constant current charge and discharge were applied to lithium-ion battery modules. In the experimental part of the research, an isothermal battery calorimeter was used to determine the heat dissipation of lithium-ion batteries. Thermal performance was simulated for the presence of phase change material composites. Simulation outcomes demonstrate that phase change material cooling considerably decreases the lithium-ion battery temperature increase during fast charging and discharging conditions use. The greatest temperature at the end of 9 C, 7 C, 5 C, and 3 C charges and discharges were approximately 49.7, 44.6, 38.4, and 33.1 °C, respectively, demonstrating satisfactory performance in lithium-ion battery thermal homogeneity of the passive thermal management system.

Evaluation of Combined Active and Passive Thermal Management Strategies for Lithium-Ion Batteries

2016 ◽  
Vol 13 (3) ◽  
Author(s):  
Carlos F. Lopez ◽  
Judith A. Jeevarajan ◽  
Partha P. Mukherjee
Keyword(s):  
Phase Change ◽  
Lithium Ion Batteries ◽  
Phase Change Material ◽  
Thermal Management ◽  
Management Strategies ◽  
Lithium Ion ◽  
Operating Conditions ◽  
Management Systems ◽  
Trade Offs ◽  
Change Material

Lithium-ion batteries are the most commonly used portable energy storage technology due to their relatively high specific energy and power but face thermal issues that raise safety concerns, particularly in automotive and aerospace applications. In these environments, there is zero tolerance for catastrophic failures such as fire or cell rupture, making thermal management a strict requirement to mitigate thermal runaway potential. The optimum configurations for such thermal management systems are dependent on both the thermo-electrochemical properties of the batteries and operating conditions/engineering constraints. The aim of this study is to determine the effect of various combined active (liquid heat exchanger) and passive (phase-change material) thermal management techniques on cell temperatures and thermal balancing. The cell configuration and volume/weight constraints have important roles in optimizing the thermal management technique, particularly when utilizing both active and passive systems together. A computational modeling study including conjugate heat transfer and fluid dynamics coupled with thermo-electrochemical dynamics is performed to investigate design trade-offs in lithium-ion battery thermal management strategies. It was found that phase-change material properties and cell spacing have a significant effect on the maximum and gradient of temperature in a module cooled by combined active and passive thermal management systems.

Experimental Study on Thermal Characteristics of Finned Coil LHSU Using Paraffin as Phase Change Material

2017 ◽  
Vol 139 (4) ◽  
Author(s):  
Guansheng Chen ◽  
Nanshuo Li ◽  
Huanhuan Xiang ◽  
Fan Li
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Phase Change ◽  
Phase Change Material ◽  
Water Flow ◽  
Water Flow Rate ◽  
Thermal Characteristics ◽  
Heat Transfer Fluid ◽  
Latent Heat Storage ◽  
Change Material

It is well known that attaching fins on the tubes surfaces can enhance the heat transfer into and out from the phase change materials (PCMs). This paper presents the results of an experimental study on the thermal characteristics of finned coil latent heat storage unit (LHSU) using paraffin as the phase change material (PCM). The paraffin LHSU is a rectangular cube consists of continuous horizontal multibended tubes attached vertical fins at the pitches of 2.5, 5.0, and 7.5 mm that creates the heat transfer surface. The shell side along with the space around the tubes and fins is filled with the material RT54 allocated to store energy of water, which flows inside the tubes as heat transfer fluid (HTF). The measurement is carried out under four different water flow rates: 1.01, 1.30, 1.50, and 1.70 L/min in the charging and discharging process, respectively. The temperature of paraffin and water, charging and discharging wattage, and heat transfer coefficient are plotted in relation to the working time and water flow rate.

Sign in / Sign up

Export Citation Format

Share Document