Research of Fretting Fatigue Characteristics of a Fiber Metal Laminate – A Steel Single-Lap Joint

2021 ◽  
Author(s):  
C. B. Wu ◽  
X. C. Ping ◽  
X. Zeng ◽  
Q. Guo ◽  
Q. H. Huang ◽  
...  
Keyword(s):  
Fretting Fatigue ◽  
Lap Joint ◽  
Single Lap Joint ◽  
Fiber Metal Laminate ◽  
Fatigue Characteristics ◽  
Fiber Metal

scholarly journals Chemically Grafting Carbon Nanotubes onto Carbon Fibers for Enhancing Interfacial Properties of Fiber Metal Laminate

Materials ◽  
2020 ◽  
Vol 13 (17) ◽  
pp. 3813
Author(s):  
Fan Ji ◽  
Cheng Liu ◽  
Yubing Hu ◽  
Shengnan Xu ◽  
Yiyan He ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Carbon Fibers ◽  
Photoelectron Spectroscopy ◽  
Elemental Content ◽  
Lap Joint ◽  
Curing Conditions ◽  
Fiber Metal Laminate ◽  
Bonding Properties ◽  
Bond Strengths ◽  
Fiber Metal

This paper primarily investigates the effects of chemically grafted modified carbon fibers on the bonding properties of fiber metal laminates (FMLs). Relative elemental content on the carbon fibers’ surface was performed via X-ray photoelectron spectroscopy (XPS). Scanning electron microscopy (SEM) was utilized to observe the material microstructure. The effect of chemically grafted carbon fibers on the bond strengths of FMLs was experimentally investigated through lap joint testing. The carbon nanotubes (CNTs) grafting concentration and curing conditions of the samples were also investigated. The test results demonstrate that grafting concentrations of 0.1, 0.2, and 0.3 mg/mL CNT solution increased the bond strength of the cured samples under vacuum conditions by 63.51%, 87.16%, and 71.56%, respectively. In addition, the bond strengths of vacuum-cured samples were also increased.

Kekuatan Sambungan AL/CFRP Menggunakan Adhesif Epoksi/Serbuk-AL dengan Variasi Pressure Level

2017 ◽  
Vol 1 (1) ◽  
Author(s):  
Bi Asngali
Keyword(s):  
Pressure Level ◽  
Lap Joint ◽  
Single Lap Joint ◽  
Al 2024

 Penelitian ini bertujuan untuk menyelidiki pengaruh pressure level terhadap kekuatan geser sambungan single lap joint (SLJ) antara Al 2024 dan CFRP dengan adesif epoksi/serbuk Al. Variasi pressure level yang digunakan adalah 0,6; 0,7; 0,8; 0,9 dan 1 MPa. Pembuatan dan pengujian spesimen uji geser mengacu pada ASTM D 1002. Hasil penelitian menunjukkan bahwa pressure level dapat meningkatkan kekuatan geser sambungan. Pada variabel pressure level terbaiknya yaitu 0,9 MPa menghasilkan kekuatan geser tertinggi (8,59 MPa). Pada kondisi tersebut, penampang patahan menunjukkan jenis kegagalan kombinasi antara kegagalan cohesive, light fiber tear dan fiber-tear.Kata kunci— pressure level; epoksi/serbuk-Al; kekuatan geser; single lap joint .

Experimental and FEA Evaluation of Hybrid Joint Strength of Single Lap joint

2011 ◽  
Vol 1 (9) ◽  
pp. 93-96
Author(s):  
S. S. Kadam S. S. Kadam ◽  
◽  
P. A. Dixit P. A. Dixit
Keyword(s):  
Joint Strength ◽  
Lap Joint ◽  
Single Lap Joint ◽  
Hybrid Joint

scholarly journals Application of the Point Stress Criterion to Assess the Bond Strength of a Single-Lap Joint

2014 ◽  
Vol 46 (4) ◽  
pp. 518-525
Author(s):  
K. S. Sajikumar ◽  
N. Asok Kumar ◽  
B. Nageswara Rao
Keyword(s):  
Bond Strength ◽  
Lap Joint ◽  
Stress Criterion ◽  
Single Lap Joint

Increasing single-lap joint strength by adherend curvature-induced residual stresses

2013 ◽  
Vol 27 (3) ◽  
pp. 244-251 ◽  
Author(s):  
Ş. Temiz ◽  
S. Akpinar ◽  
M.D. Aydın ◽  
E. Sancaktar
Keyword(s):  
Residual Stresses ◽  
Joint Strength ◽  
Lap Joint ◽  
Single Lap Joint

On impact behavior of fiber metal laminate (FML) structures: A state-of-the-art review

2021 ◽  
Vol 167 ◽  
pp. 108026
Author(s):  
Wentao He ◽  
Linfeng Wang ◽  
Huancai Liu ◽  
Changzi Wang ◽  
Lu Yao ◽  
...  
Keyword(s):  
State Of The Art ◽  
Impact Behavior ◽  
Fiber Metal Laminate ◽  
Fiber Metal

scholarly journals Impact Response of Cantilever Fiber Metal Laminate (FML) Plates Using a Coupled Analytical-Numerical Method

2013 ◽  
Vol 5 (21) ◽  
pp. 5112-5118
Author(s):  
Faramarz Ashenai Ghasemi ◽  
Reza Paknejad ◽  
Keramat Malekzadeh Fard ◽  
Nasrollah Banimostafa Arab
Keyword(s):  
Numerical Method ◽  
Impact Response ◽  
Fiber Metal Laminate ◽  
Fiber Metal
Sign in / Sign up

Export Citation Format

Share Document