Numerical simulation of a new hollow stationary dehumidity blade in last stage of steam turbine

2011 ◽  
Vol 5 (3) ◽  
Author(s):  
Youmin Hou ◽  
Danmei Xie ◽  
Wangfan Li ◽  
Xinggang Yu ◽  
Yang Shi ◽  
...  
Author(s):  
Fang Li ◽  
Shunsen Wang ◽  
Juan Di ◽  
Zhenping Feng

Abstract In order to study the effect of initial surface roughness on water droplet erosion resistance of last stage blade substrate of steam turbine, eight 17-4PH samples were grounded and velvet polished by different mesh metallographic sandpaper to establish sample with different initial surface roughness. The water droplet erosion experiments were carried out in the highspeed jet water erosion experiment system, and the mass and micro-morphology of each sample were measured by using precision electronic balance and ultra-depth of field microscope respectively at each experimental stage, and the measurement of water erosion trace width and maximum water erosion depth were also completed at the same time. On the basis of experiments, LS-DYNA was used for numerical simulation to verify the reliability of experimental results again. Results show that the smoother the initial surface of sample, then the smaller the mass loss, the stronger its water erosion resistance. On the contrary, the rougher the initial surface of sample, the more severe the surface irregularity, the more times the water droplets concentrated at the lowest point of pit when water droplets flow laterally after impact is completed, thus accelerating the formation of initial crack and lateral expansion, the poorer the water erosion resistance of sample. At same water erosion time, the smoother the sample surface, the later the complete erosion trace appear, the narrower the water erosion trace width. However, the maximum water erosion depth of sample is not affected by the initial surface roughness. The numerical simulation results are in good agreement with the experimental results.


2010 ◽  
Vol 02 (04) ◽  
pp. 248-253 ◽  
Author(s):  
Danmei Xie ◽  
Xinggang Yu ◽  
Wangfan Li ◽  
Youmin Hou ◽  
Yang Shi ◽  
...  

2021 ◽  
Vol 1096 (1) ◽  
pp. 012097
Author(s):  
A M Kongkong ◽  
H Setiawan ◽  
J Miftahul ◽  
A R Laksana ◽  
I Djunaedi ◽  
...  

1976 ◽  
Vol 98 (3) ◽  
pp. 573-577 ◽  
Author(s):  
J. Krzyz˙anowski ◽  
B. Weigle

In a series of experiments aimed at the visualization of the wet steam flow in the exhaust part of a 200 MW condensing steam turbine a set of periscopes and light sources was used. The aim of the experiment was: 1 – The investigation of the liquid-phase flow over the last stage stator blading of the turbine mentioned. 2 – The investigation of the gaseous-phase flow through the last stage blading at full and part load. The first part of the program partially failed due to the opaqueness of the wet steam atmosphere for the turbine load higher than 10–20 MW. The detailed experimental conditions will be described. An assessment of the primary droplet size will also be given. The preliminary results of the second part of the program will be outlined. The advantages and disadvantages of the equipment used will be discussed.


Author(s):  
Eric Liese

A dynamic process model of a steam turbine, including partial arc admission operation, is presented. Models were made for the first stage and last stage, with the middle stages presently assumed to have a constant pressure ratio and efficiency. A condenser model is also presented. The paper discusses the function and importance of the steam turbines entrance design and the first stage. The results for steam turbines with a partial arc entrance are shown, and compare well with experimental data available in the literature, in particular, the “valve loop” behavior as the steam flow rate is reduced. This is important to model correctly since it significantly influences the downstream state variables of the steam, and thus the characteristic of the entire steam turbine, e.g., state conditions at extractions, overall turbine flow, and condenser behavior. The importance of the last stage (the stage just upstream of the condenser) in determining the overall flowrate and exhaust conditions to the condenser is described and shown via results.


Sign in / Sign up

Export Citation Format

Share Document