Effect of Additive Elements (x = Cr, Mn, Zn, Sn) on the Phase Evolution and Thermodynamic Complexity of AlCuSiFe-x High Entropy Alloys Fabricated via Powder Metallurgy

2022 ◽  
Author(s):  
Ashutosh Sharma ◽  
Hansung Lee ◽  
Byungmin Ahn
Keyword(s):  
Powder Metallurgy ◽  
Phase Evolution ◽  
High Entropy Alloys ◽  
High Entropy

A Study on the Phase Formation and Magnetic Properties of FeNiCoCuM (M = Mo, Nb) High-Entropy Alloys Processed Through Powder Metallurgy

2021 ◽  
Vol 52 (3) ◽  
pp. 1044-1058
Author(s):  
P. Martin ◽  
C. Salvo ◽  
E. Pio ◽  
G. Neves ◽  
Henry A. Colorado ◽  
...  
Keyword(s):  
Magnetic Properties ◽  
Powder Metallurgy ◽  
Phase Formation ◽  
High Entropy Alloys ◽  
High Entropy

scholarly journals Effect of Copper Addition on the AlCoCrFeNi High Entropy Alloys Properties via the Electroless Plating and Powder Metallurgy Technique

Crystals ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 540
Author(s):  
Mohamed Ali Hassan ◽  
Hossam M. Yehia ◽  
Ahmed S. A. Mohamed ◽  
Ahmed Essa El-Nikhaily ◽  
Omayma A. Elkady
Keyword(s):  
Compressive Strength ◽  
Powder Metallurgy ◽  
Atomic Radius ◽  
The Other ◽  
High Entropy Alloy ◽  
Coating Process ◽  
High Entropy Alloys ◽  
Powder Metallurgy Technique ◽  
Copper Metal ◽  
High Entropy

To improve the AlCoCrFeNi high entropy alloys’ (HEAs’) toughness, it was coated with different amounts of Cu then fabricated by the powder metallurgy technique. Mechanical alloying of equiatomic AlCoCrFeNi HEAs for 25 h preceded the coating process. The established powder samples were sintered at different temperatures in a vacuum furnace. The HEAs samples sintered at 950˚C exhibit the highest relative density. The AlCoCrFeNi HEAs model sample was not successfully produced by the applied method due to the low melting point of aluminum. The Al element’s problem disappeared due to encapsulating it with a copper layer during the coating process. Because the atomic radius of the copper metal (0.1278 nm) is less than the atomic radius of the aluminum metal (0.1431 nm) and nearly equal to the rest of the other elements (Co, Cr, Fe, and Ni), the crystal size powder and fabricated samples decreased by increasing the content of the Cu wt%. On the other hand, the lattice strain increased. The microstructure revealed that the complete diffusion between the different elements to form high entropy alloy material was not achieved. A dramatic decrease in the produced samples’ hardness was observed where it decreased from 403 HV at 5 wt% Cu to 191 HV at 20 wt% Cu. On the contrary, the compressive strength increased from 400.034 MPa at 5 wt% Cu to 599.527 MPa at 15 wt% Cu with a 49.86% increment. This increment in the compressive strength may be due to precipitating the copper metal on the particles’ surface in the nano-size, reducing the dislocations’ motion, increasing the stiffness of produced materials. The formability and toughness of the fabricated materials improved by increasing the copper’s content. The thermal expansion has increased gradually by increasing the Cu wt%.

Compression stress strengthening modelling of a ultrafine-grained equiatomic SPS CoCrFeNiNb high-entropy alloy

2020 ◽  
pp. 095440622094324
Author(s):  
Marcello Cabibbo ◽  
Filip Průša ◽  
Alexandra Šenková ◽  
Andrea Školáková ◽  
Vojtěch Kučera ◽  
...  
Keyword(s):  
Powder Metallurgy ◽  
Mechanical Alloying ◽  
Oxide Phase ◽  
High Entropy Alloy ◽  
Induction Melting ◽  
High Entropy Alloys ◽  
High Entropy ◽  
Plasma Sintering ◽  
Transmission Electron ◽  
Spark Plasma

High-entropy alloys are known to show exceptionally high mechanical properties, both compression and tensile strength, and unique physical properties, such as their phase stability. These quite unusual properties are primarily due to the microstructure generated by mechanical alloying processes, such as conventional induction arc melting, powder metallurgy, or mechanical alloying. In the present study, an equiatomic CoCrFeNiNb high-entropy alloy was prepared by a sequence of conventional induction melting, powder metallurgy, and compaction via spark plasma sintering. The high-entropy alloys showed uniform sub-micrometer grain microstructure consisted by a mixture of an fcc solid solution strengthened by a hcp Laves phase and a third intergranular oxide phase. The as-cast high-entropy alloys showed an ultimate compression strength (UCS) of ∼1400 MPa, which after sintering and compaction at 1273 K increased up to ∼2400 MPa. Extensive transmission electron microscopy quantitative analyses were carried out to model the UCS. A quite good agreement between the microstructure-strengthening model and the experimental UCS was found.

Powder metallurgy and high-entropy alloys: update on new opportunities

2020 ◽  
Vol 63 (4) ◽  
pp. 227-236
Author(s):  
José M. Torralba ◽  
Paula Alvaredo ◽  
Andrea García-Junceda
Keyword(s):  
Powder Metallurgy ◽  
High Entropy Alloys ◽  
High Entropy

Effects of processing route on phase evolution and mechanical properties of CoCrCuFeNiSix high entropy alloys

2018 ◽  
Vol 748 ◽  
pp. 889-897 ◽  
Author(s):  
Anil Kumar ◽  
Akhilesh Kumar Swarnakar ◽  
A. Basu ◽  
Manoj Chopkar
Keyword(s):  
Mechanical Properties ◽  
Phase Evolution ◽  
Processing Route ◽  
High Entropy Alloys ◽  
High Entropy
Sign in / Sign up

Export Citation Format

Share Document