Simulation of hertz transient contact/impact of flexible bodies

2012 ◽  
Vol 23 (2) ◽  
pp. 225-232 ◽  
Author(s):  
Changgen Bu ◽  
Boru Xia ◽  
Yinjun Lian ◽  
Hui Zeng
Sensors ◽  
2019 ◽  
Vol 20 (1) ◽  
pp. 233
Author(s):  
Yanze Li ◽  
Yunian Shen ◽  
Qiaoping Xing

The transient contact-impact mechanism and driving capability of the piezoelectric stack actuator is analyzed using both experimental and theoretical methods. An experimental setup and its corresponding measurement approaches for the transient responses are designed. The launch range of the object resulting from the first contact-impact is measured through laser doppler vibrometer and the motion process is captured by high-speed camera. Experimental results illustrate that the launch range increases firstly and decreases subsequently as the frequency of the sine driving voltage increases. Meanwhile, considering the local viscoelastic contact deformation, a theoretical methodology including the mechanics model for the driving process is proposed. Based on the Lagrange equations of second kind, the governing equation of the driving system is derived. Transient responses are calculated using the fourth-order Runge–Kutta integration method. Contact forces and Poisson’s coefficient of restitution are calculated by the proposed theoretical method. The results of launch range show that the theoretical solutions have a good agreement with the experimental data. The peak value of contact force increases firstly and decreases subsequently with the increase of voltage frequency. In addition, the coefficient of restitutions is roughly 0.9 when f is greater than 3.5 kHz.


2017 ◽  
Vol 66 (15) ◽  
pp. 154501
Author(s):  
Wang Jian-Yao ◽  
Liu Zhu-Yong ◽  
Hong Jia-Zhen

2018 ◽  
Vol 2018 ◽  
pp. 1-10 ◽  
Author(s):  
Qing-liang Zeng ◽  
Zhao-sheng Meng ◽  
Li-rong Wan ◽  
Cheng-long Wang

To study the load transfer characteristics of a two-legged shield powered support, a numerical simulation model of the support was established using the multibody dynamics software ADAMS. The model took full account of the hydraulic-elastic deformation characteristics of the support, as a series spring-damper system was used to replace the leg and the equilibrium jack. The canopy, goaf shield, lemniscate bars, and equilibrium jack are equivalent to flexible bodies. The setting force of the leg was provided by the preload of the equivalent spring, the static roof load was simulated using a slope signal, and the impact load was simulated using a step signal. Using the model, the impact and excitation effects of each hinge joint of the support were analyzed under different impact load conditions across the canopy. The results show that the location of the impact load affects the force transmissions of all hinge points of the support. Both the impact effect and the excitation effect are at a minimum when the impact force is located near the leg action line. These results are useful for the adaptive control and structural design optimization of the support.


Author(s):  
Juhwan Choi ◽  
Jin Hwan Choi

The contact analysis of multi-flexible-body dynamics (MFBD) has been an important issue in the area of computational dynamics because the realistic dynamic analysis of many mechanical systems includes the contacts among rigid and flexible bodies. But, until now, the contact analysis in the multi-flexible-body dynamics has still remained as a big, challenging area. Especially, the most of contact algorithms have been developed based on the facetted triangles. As a result, the contact force based on the facetted surface was not accurate and smooth because the geometrical error is already included in the contact surface representation stage. This kind of error can be very important in the precise mechanism such as gear contact or cam-valve contact problems. In order to resolve this problem, this study suggests a cubic spline surface representation method and related contact algorithms. The proposed contact algorithms are using the compliant contact force model based on the Hertzian contact theory. In order to evaluate the smooth contact force, the penetration depth and contact normal directions are evaluated by using the cubic spline surface interpolation. Also, for the robust and efficient contact algorithm development, the contact algorithms are divided into four main parts which are a surface representation, a pre-search, a detailed search and a contact force generation. In the surface representation part, we propose a smooth surface representation method which can be used for smooth rigid and flexible bodies. In the pre-search, the algorithm performs collision detection and composes the expected contact pairs for the detailed search. In the detailed search, the penetration depth and contact reference frame are calculated with the cubic spline surface interpolation in order to generate the accurate and smooth contact force. Finally in the contact force generation part, we evaluate the contact force and Jacobian matrix for the implicit time integrator.


2003 ◽  
Vol 7 (5) ◽  
pp. 364-372 ◽  
Author(s):  
Meng Chen ◽  
Liping Chen ◽  
Xinfang Zhang ◽  
Hemin Bai ◽  
Yuzhi Xiao

Sign in / Sign up

Export Citation Format

Share Document