Temperature Influence on High-Density Polyethylene Geomembrane and Soil Interface Shear Strength

2021 ◽  
Vol 7 (3) ◽  
Author(s):  
Ö. Bilgin ◽  
B. Shah
Keyword(s):  
Shear Strength ◽  
High Density Polyethylene ◽  
High Density ◽  
Temperature Influence ◽  
Interface Shear Strength ◽  
Interface Shear ◽  
Soil Interface

Influence of degree of saturation on soil nail pull-out resistance in compacted completely decomposed granite fill

2007 ◽  
Vol 44 (11) ◽  
pp. 1314-1328 ◽  
Author(s):  
Li-Jun Su ◽  
Terence C.F. Chan ◽  
Y.K. Shiu ◽  
Tony Cheung ◽  
Jian-Hua Yin
Keyword(s):  
Shear Strength ◽  
Degree Of Saturation ◽  
Interface Shear Strength ◽  
Interface Shear ◽  
Soil Nails ◽  
Soil Nail ◽  
Pull Out ◽  
Decomposed Granite ◽  
Soil Interface ◽  
Completely Decomposed Granite

The nail–soil interface shear strength is a key parameter in the design and stability assessment of soil nailing systems. A number of factors will influence the nail–soil interface shear strength. Among these factors, the degree of saturation (Sr) of the soil is an important one especially for permanent soil nail structures. To study the influence of Sr on soil nail pull-out shear resistance, a series of laboratory pull-out tests have been conducted on soil nails in compacted completely decomposed granite (CDG) fill prepared to different Sr. The tests were conducted using two specially designed pull-out boxes (with same specifications). In the near-saturated tests, a high Sr (about 98%) was achieved using two special features of the apparatus: a waterproof front cap and back-water pressure pipes at the bottom of the pull-out box. Test results showed that the nail–soil shearing plane migrated outwards into the soil when the Sr of the soil increased. Also, peak pull-out strengths of soil nails were strongly influenced by the Sr of the soil. Among the tested Sr, the highest values of peak pull-out shear strength were obtained at Sr values between 50% and 75%.

scholarly journals Degree of saturation effect on the grout-soil interface shear strength of soil nailing

2016 ◽  
Vol 9 ◽  
pp. 15007 ◽  
Author(s):  
Qiong Wang ◽  
Xinyu Ye ◽  
Shanyong Wang ◽  
Scott William Sloan ◽  
Daichao Sheng
Keyword(s):  
Shear Strength ◽  
Saturation Effect ◽  
Degree Of Saturation ◽  
Soil Nailing ◽  
Interface Shear Strength ◽  
Interface Shear ◽  
Soil Interface

Influence of revision arthroplasty on bone/cement interface shear strength

1987 ◽  
Vol 20 (8) ◽  
pp. 824
Author(s):  
J.E. Bechtold ◽  
Y. Dohmae ◽  
R.E. Sherman ◽  
R.B. Gustilo
Keyword(s):  
Shear Strength ◽  
Bone Cement ◽  
Revision Arthroplasty ◽  
Interface Shear Strength ◽  
Interface Shear ◽  
Cement Interface

scholarly journals Skewness and Kurtosis: Important Parameters in the Characterization of Dental Implant Surface Roughness—A Computer Simulation

2011 ◽  
Vol 2011 ◽  
pp. 1-6 ◽  
Author(s):  
Karl Niklas Hansson ◽  
Stig Hansson
Keyword(s):  
Surface Roughness ◽  
Shear Strength ◽  
Roughness Parameter ◽  
Interface Shear Strength ◽  
Interface Shear ◽  
Implant Surface ◽  
Bone Response ◽  
Dental Implant Surface ◽  
Skewness And Kurtosis

The surface roughness affects the bone response to dental implants. A primary aim of the roughness is to increase the bone-implant interface shear strength. Surface roughness is generally characterized by means of surface roughness parameters. It was demonstrated that the normally used parameters cannot discriminate between surfaces expected to give a high interface shear strength from surfaces expected to give a low interface shear strength. It was further demonstrated that the skewness parameter can do this discrimination. A problem with this parameter is that it is sensitive to isolated peaks and valleys. Another roughness parameter which on theoretical grounds can be supposed to give valuable information on the quality of a rough surface is kurtosis. This parameter is also sensitive to isolated peaks and valleys. An implant surface was assumed to have a fairly well-defined and homogenous “semiperiodic” surface roughness upon which isolated peaks were superimposed. In a computerized simulation, it was demonstrated that by using small sampling lengths during measurement, it should be possible to get accurate values of the skewness and kurtosis parameters.

Shear strength and temperature distribution model of friction spot lap joint of high density polyethylene with aluminum alloy 7075

2019 ◽  
Vol 10 (4) ◽  
pp. 469-483 ◽  
Author(s):  
Isam Tareq Abdullah ◽  
Sabah Khammass Hussein
Keyword(s):  
Shear Strength ◽  
Temperature Distribution ◽  
High Density Polyethylene ◽  
Contact Region ◽  
High Density ◽  
Distribution Model ◽  
Lap Joint ◽  
Content Type ◽  
Rotating Speed ◽  
Model Of Friction

Purpose The purpose of this paper is to join a sheet of the AA7075 with the high-density polyethylene (HDPE) by a lap joint using friction spot processing and investigate the temperature distribution of joint during this process using the finite element method (FEM). Design/methodology/approach A semi-conical hole was manufactured in the AA7075 specimen and a lap joint configuration was prepared with the HDPE specimen. A rotating tool was used to generate the required heat to melt the polymer by the friction with the AA7075 specimen. The applied tool force moved the molten polymer through the hole. Four parameters were used: lower diameter of hole, rotating speed, plunging depth and time. The results of shear test were analyzed using the Taguchi method. A FEM was presented to estimate the temperature distribution of joint during the process. Findings All specimens failed by shearing the polymer at the lap joint region without dislocation. The specimens of the smallest diameter exhibited the highest shear strength at the lap joint. The maximum ranges of temperature were recorded at the contact region between the rotating tool and the AA7075 specimen. The tool plunging depth recorded the highest effect on the generated heat compared with the rotating speed and plunging time. Originality/value For the first time, the AA7075 sheet was joined with the HDPE sheet by friction spot processing. The temperature distribution of this joint was simulated using the FEM.

Sign in / Sign up

Export Citation Format

Share Document