Does Additive Pressurized Carbon Dioxide Lavage Improve Cement Penetration and Bond Strength in Cemented Arthroplasty?

The modern cementing technique in cemented arthroplasty is a highly standardized and, therefore, safe procedure. Nevertheless, aseptic loosening is still the main reason for revision after cemented total knee or cemented total hip arthroplasty. To investigate whether an additional carbon dioxide lavage after a high-pressure pulsatile saline lavage has a positive effect on the bone–cement interface or cement penetration, we set up a standardized laboratory experiment with 28 human femoral heads. After a standardized cleaning procedure, the test implants were cemented onto the cancellous bone. Subsequently, the maximum failure load of the bone–cement interface was determined using a material testing machine to pull off the implant, and the cement penetration was determined using computed tomography. Neither the maximum failure load nor cement penetration into the cancellous bone revealed significant differences between the groups. In conclusion, according to our experiments, the additive use of the carbon dioxide lavage after the high-pressure pulsatile lavage has no additional benefit for the cleaning of the cancellous bone and, therefore, cannot be recommended without restrictions.

Pressurized Carbon Dioxide Lavage Reduces the Incidence of a Radiolucent Line Around the Tibial Component Two Years After Total Knee Arthroplasty

Introduction: In cemented total knee arthroplasty (TKA), pressurized carbon dioxide (CO2) lavage prior to cement fixation can eliminate debris at the bone-cement interface and is considered effective for increasing cement penetration and preventing aseptic loosening. Regarding the risk of a preliminary diagnosis of implant loosening, a radiolucent line (RLL) is a valuable sign. The purpose of this study was to compare the incidence of a tibial RLL at 2 years after TKA with and without pressurized CO2 lavage.Methods: This is a retrospective study. One hundred knees from 98 patients were enrolled in this study. TKA was performed without pressurized CO2 lavage (CO2- group) for the first 47 knees, and with pressurized CO2 lavage (CO2+ group) for the next 53 knees. The depth of cement penetration was measured just after surgery, and the incidence of tibial RLL >2 mm, at 2 years after TKA was determined. Results: Significant differences between groups were not seen regarding pre- and postoperative clinical factors. The depth of cement penetration in each area was significantly higher in the CO2+ group. The frequency of knees with RLL >2 mm was significantly lower in the CO2+ group than in the CO2- group (p<0.001).Conclusions: Pressurized CO2 lavage improved cement penetration and decreased the incidence of tibial RLL >2 mm at 2 years after TKA. Since the RLL has been reported as a valuable sign for preliminary diagnosis of loosening, pressurized CO2 lavage appears effective for preventing loosening.

Investigation of Stress State During Cement Hardening and its Effect on Failure of Cement Sheath in Shale Gas Wells

Consideration of initial stress state after cement hardening provides a vital basis for the prediction of cement failure, which has been overlooked in previously published methodologies partly due to the difficulties in examining this problem rationally. In the present study, the hoop stress at casing-cement interface during cement hardening is investigated experimentally based on the full-scale casing-cement sheath-formation system (CCFS) facility, which is equipped with the real-time stress-strain measurement capability. The hoop stress at casing-cement interface during cement hardening drops sharply, rather than equating with the initial annulus pressure of cement slurry. It presents a higher drawdown under higher annulus pressure and thinner casing, and a lower drawdown under elastic cement slurry and thicker cement sheath. Furthermore, an analytical model taking the effect of cement hardening into account is developed to predict the integrity of cement sheath. Reliability of the model is verified by comparison with field observations. Excellent agreements are observed. The results illustrate that the tensile cracks are likely to occur at the inner cement (inner surface of cement sheath) by the effect of cement hardening, since the hoop stress at inner cement during cement hardening drops greatly and even becomes tensile. A detailed sensitivity analysis illustrates that an elastic cement slurry with a lower elastic modulus works more effectively, which can resolve the SCP problem in shale gas wells.

Effect of Luting Cement Film Thickness on the Pull-Out Bond Strength of Endodontic Post Systems

Optimal bond strength between the prefabricated post/dowel to the surrounding dentin is essential. The present study aimed to analyze and compare the effect of three different cement film thicknesses on the pull-out bond strength of three different prefabricated post systems. Extracted natural teeth (N = 90) with similar root dimensions were acquired. Teeth were mounted in resin blocks, endodontically treated, sectioned at cemento-enamel junction, divided into three groups (A: Parapost Fiber Lux plus; B: 3M ESPE Relyx fiber post; and C: Parapost XP), and stored. Uniform post spaces were prepared for the groups (A and C: Length = 8 mm, Width = 1.5 mm; B: Length = 8 mm, Width = 1.6 mm). Each group (N = 30) was further subdivided into three subgroups (n = 10) based on the size (4, 5, and 6) of the post and cemented with resin cement (MultiLink-N, Ivoclar Vivadent). After thermocycling, the specimens were subjected to a pull-out test using a universal testing machine, and tensile force was recorded (MPa). Digital microscopic evaluations were performed for modes of failure. ANOVA and Tukey-HSD tests were used for statistics. Significant differences were observed for each tested material (p = 0.000). The lowest and highest bond strength values were recorded for Group C (Titanium post) and Group A (000), respectively. Multiple comparisons showed significance (p < 0.05) among all the groups, except for space 1 and space 2 (p = 0.316) for Group A. Most of the failures occurred within the cement-dentin and post-cement interface (Adhesive failures, 73.5%). An increase in the luting cement film thickness results in the decrease in pull-out bond strength of prefabricated posts luted with resin cement, irrespective of the type/material/shape of the post. The serrated fiber posts showed the highest pull-out bond strength compared to the smooth surfaced fiber posts or serrated metal posts. Increased pull-out bond strengths were observed when appropriate post space was created with the same sized drill as the post size.

Comparative Evaluation of Two Glass Polyalkenoate Cements: An In Vivo Pilot Study Using a Sheep Model

Poly(methyl methacrylate) (PMMA) is used to manage bone loss in revision total knee arthroplasty (rTKA). However, the application of PMMA has been associated with complications such as volumetric shrinkage, necrosis, wear debris, and loosening. Glass polyalkenoate cements (GPCs) have potential bone cementation applications. Unlike PMMA, GPC does not undergo volumetric shrinkage, adheres chemically to bone, and does not undergo an exothermic setting reaction. In this study, two different compositions of GPCs (GPCA and GPCB), based on the patented glass system SiO2-CaO-SrO-P2O5-Ta2O5, were investigated. Working and setting times, pH, ion release, compressive strength, and cytotoxicity of each composition were assessed, and based on the results of these tests, three sets of samples from GPCA were implanted into the distal femur and proximal tibia of three sheep (alongside PMMA as control). Clinical CT scans and micro-CT images obtained at 0, 6, and 12 weeks revealed the varied radiological responses of sheep bone to GPCA. One GPCA sample (implanted in the sheep for 12 weeks) was characterized with no bone resorption. Furthermore, a continuous bone–cement interface was observed in the CT images of this sample. The other implanted GPCA showed a thin radiolucent border at six weeks, indicating some bone resorption occurred. The third sample showed extensive bone resorption at both six and 12 weeks. Possible speculative factors that might be involved in the varied response can be: excessive Zn2+ ion release, low pH, mixing variability, and difficulty in inserting the samples into different parts of the sheep bone.