A Highly Accurate Algorithm for Nonlinear Numerical Simulation of RC Columns Under Biaxial Bending Moment and Axial Loading Applying Rotary Oblique Fiber-Element Discretization

2017 ◽  
Vol 15 (8) ◽  
pp. 1117-1129 ◽  
Author(s):  
Kabir Sadeghi ◽  
Fatemeh Nouban
Keyword(s):  
Numerical Simulation ◽  
Axial Loading ◽  
Bending Moment ◽  
Biaxial Bending ◽  
Rc Columns ◽  
Element Discretization ◽  
Fiber Element ◽  
Nonlinear Numerical Simulation

ANALYSIS OF AN INTERNAL FIXATION OF A LONG BONE FRACTURE

2005 ◽  
Vol 05 (01) ◽  
pp. 89-103 ◽  
Author(s):  
K. RAMAKRISHNA ◽  
I. SRIDHAR ◽  
S. SIVASHANKER ◽  
V. K. GANESH ◽  
D. N. GHISTA
Keyword(s):  
Stress Shielding ◽  
Axial Loading ◽  
Bending Moment ◽  
Fracture Site ◽  
Long Bone ◽  
Radius Of Curvature ◽  
Element Analysis ◽  
Long Bone Fracture ◽  
Fracture Interface ◽  
Tensile Surface

A major concern when a fractured bone is fastened by stiff-plates to the bone on its tensile surface is excessive stress shielding of the bone. The compressive stress shielding at the fracture-interface immediately after fracture-fixation delays bone healing. Likewise, the tensile stress shielding of the healed bone underneath the plate also does not enable it to recover its tensile strength. Initially, the effect of a uniaxial load and a bending moment on the assembly of bone and plate is investigated analytically. The calculations showed that the screws near the fracture site transfers more load than the screws away from the fracture site in axial loading and it is found that less force is required when the screw is placed near to fracture site than the screw placed away from the fracture site to make the bone and plate bend with same radius of curvature when subjected to bending moment. Finally, the viability of using a stiffness graded bone-plate as a fixator is studied using finite element analysis (FEA): the stiffness-graded plate cause less stress-shielding than stainless steel plate.

scholarly journals Lateral shear strength of rectangular RC columns subjected to combined P-V-M monotonic loading

2020 ◽  
Vol 53 (4) ◽  
pp. 227-241
Author(s):  
Aysha M Zaneeb ◽  
Rupen Goswami ◽  
C V R Murty
Keyword(s):  
Shear Strength ◽  
Test Data ◽  
Rectangular Cross Section ◽  
Resistance Mechanism ◽  
Bending Moment ◽  
Shear Resistance ◽  
Shear Capacity ◽  
Longitudinal Reinforcement ◽  
Lateral Shear ◽  
Rc Columns

An analytical method is presented to estimate lateral shear strength (and identify likely mode and location of failure) in reinforced concrete (RC) cantilever columns of rectangular cross-section under combined axial force, shear force and bending moment. Change in shear capacity of concrete with flexural demand at a section is captured explicitly and the shear resistance offered by concrete estimated; this is combined with shear resistance offered by transverse and longitudinal reinforcement bars to estimate the overall shear capacity of RC columns. Shear–moment (V-M) interaction capacity diagram of an RC column, viewed alongside the demand diagram, identifies the lateral shear strength and failure mode. These analytical estimates compare well with test data of 107 RC columns published in literature; the test data corresponds to different axial loads, transverse reinforcement ratios, longitudinal reinforcement ratios, shear span to depth ratios, and loading conditions. Also, the analytical estimates are compared with those obtained using other analytical methods reported in literature; in all cases, the proposed method gives reasonable accuracy when estimating shear capacity of RC columns.  In addition, the method provides insights into the shear resistance mechanism in RC columns under the combined action of P-V-M, and it is simple to use.

scholarly journals Numerical Simulation of Dynamic Response and Evaluation of Flexural Damage of RC Columns under Horizontal Impact Load

2021 ◽  
Vol 11 (23) ◽  
pp. 11223
Author(s):  
Bin Hu ◽  
Jian Cai ◽  
Jiabin Ye
Keyword(s):  
Static Load ◽  
Impact Load ◽  
Bending Moment ◽  
Internal Force ◽  
Displacement Curve ◽  
Fe Model ◽  
Damage State ◽  
Rc Columns ◽  
Equivalent Static Load ◽  
The Impact

By using the ABAQUS finite element (FE) model, which has been verified by experiments, the deformation and internal force changes of RC columns during the impact process are investigated, and a parametric analysis is conducted under different impact kinetic energies Ek. According to the development path of the bottom bending moment-column top displacement curve under impact, the member is in a slight damage state when the curve rebounds before reaching the peak and in a moderate or severe damage state when the curve exceeds the peak, in which case the specific damage state of the member needs to be determined by examining whether there is a secondary descending stage in the curve. Accordingly, a qualitative method for evaluating the bending failure of RC column members under impact is obtained. In addition, the damage state of RC columns under impact can also be quantitatively evaluated by the ratio of the equivalent static load Feq and the ultimate static load-bearing capacity Fsu.

Sign in / Sign up

Export Citation Format

Share Document