A study of boundary vorticity dynamics and identification of large-scale structures in flow field based on two-dimensional flow around a bluff body

2019 ◽  
Vol 31 (2) ◽  
pp. 231-248
Author(s):  
Da-peng Zhang ◽  
Yu-zhu Chen ◽  
Xi-lin Xie
Keyword(s):  
Flow Field ◽  
Large Scale ◽  
Bluff Body ◽  
Two Dimensional ◽  
Large Scale Structures ◽  
Dimensional Flow ◽  
Two Dimensional Flow ◽  
Vorticity Dynamics ◽  
Scale Structures

scholarly journals Two-dimensional flow field distribution characteristics of flocking drainage pipes in tunnel

Open Physics ◽  
2020 ◽  
Vol 18 (1) ◽  
pp. 139-148
Author(s):  
Shiyang Liu ◽  
Xuefu Zhang ◽  
Feng Gao ◽  
Liangwen Wei ◽  
Qiang Liu ◽  
...  
Keyword(s):  
Flow Field ◽  
Field Distribution ◽  
Rapid Development ◽  
Maximum Velocity ◽  
Distribution Characteristics ◽  
Two Dimensional ◽  
Dimensional Flow ◽  
Laboratory Test Results ◽  
Transverse Distance ◽  
Two Dimensional Flow

AbstractWith the rapid development of traffic infrastructure in China, the problem of crystal plugging of tunnel drainage pipes becomes increasingly salient. In order to build a mechanism that is resilient to the crystal plugging of flocking drainage pipes, the present study used the numerical simulation to analyze the two-dimensional flow field distribution characteristics of flocking drainage pipes under different flocking spacings. Then, the results were compared with the laboratory test results. According to the results, the maximum velocity distribution in the flow field of flocking drainage pipes is closely related to the transverse distance h of the fluff, while the longitudinal distance h of the fluff causes little effect; when the transverse distance h of the fluff is less than 6.25D (D refers to the diameter of the fluff), the velocity between the adjacent transverse fluffs will be increased by more than 10%. Moreover, the velocity of the upstream and downstream fluffs will be decreased by 90% compared with that of the inlet; the crystal distribution can be more obvious in the place with larger velocity while it is less at the lower flow rate. The results can provide theoretical support for building a mechanism to deal with and remove the crystallization of flocking drainage pipes.

Unsteady Turbine Rim Sealing and Vane Trailing Edge Flow Effects

2021 ◽  
Author(s):  
Iván Monge-Concepción ◽  
Shawn Siroka ◽  
Reid A. Berdanier ◽  
Michael D. Barringer ◽  
Karen A. Thole ◽  
...  
Keyword(s):  
Flow Field ◽  
Unsteady Flow ◽  
Rotational Speed ◽  
Large Scale ◽  
Trailing Edge ◽  
Time Resolved ◽  
Flow Rates ◽  
Large Scale Structures ◽  
Purge Flow ◽  
Scale Structures

Abstract Hot gas ingestion into the turbine rim seal cavity is an important concern for engine designers. To prevent ingestion, rim seals use high pressure purge flow but excessive use of the purge flow decreases engine thermal efficiency. A single stage test turbine operating at engine-relevant conditions with real engine hardware was used to study time-resolved pressures in the rim seal cavity across a range of sealing purge flow rates. Vane trailing edge (VTE) flow, shown previously to be ingested into the rim seal cavity, was also included to understand its effect on the unsteady flow field. Measurements from high-frequency response pressure sensors in the rim seal and vane platform were used to determine rotational speed and quantity of large-scale structures (cells). In a parallel effort, a computational model using Unsteady Reynolds-averaged Navier-Stokes (URANS) was applied to determine swirl ratio in the rim seal cavity and time-resolved rim sealing effectiveness. The experimental results confirm that at low purge flow rates, the VTE flow influences the unsteady flow field by decreasing pressure unsteadiness in the rim seal cavity. Results show an increase in purge flow increases the number of unsteady large-scale structures in the rim seal and decreases their rotational speed. However, VTE flow was shown to not significantly change the cell speed and count in the rim seal. Simulations point to the importance of the large-scale cell structures in influencing rim sealing unsteadiness, which is not captured in current rim sealing predictive models.

Extension of the Prandtl–Batchelor theorem to three-dimensional flows slowly varying in one direction

2010 ◽  
Vol 654 ◽  
pp. 351-361 ◽  
Author(s):  
M. SANDOVAL ◽  
S. CHERNYSHENKO
Keyword(s):  
Flow Field ◽  
Small Parameter ◽  
Order Approximation ◽  
Three Dimensional ◽  
Inviscid Limit ◽  
Two Dimensional ◽  
Leading Order ◽  
Dimensional Flow ◽  
Two Dimensional Flow

According to the Prandtl–Batchelor theorem for a steady two-dimensional flow with closed streamlines in the inviscid limit the vorticity becomes constant in the region of closed streamlines. This is not true for three-dimensional flows. However, if the variation of the flow field along one direction is slow then it is possible to expand the solution in terms of a small parameter characterizing the rate of variation of the flow field in that direction. Then in the leading-order approximation the projections of the streamlines onto planes perpendicular to that direction can be closed. Under these circumstances the extension of the Prandtl–Batchelor theorem is obtained. The resulting equations turned out to be a three-dimensional analogue of the equations of the quasi-cylindrical approximation.

Sign in / Sign up

Export Citation Format

Share Document