Longitudinally-finned cross-flow tube banks and their heat transfer and pressure drop characteristics

1985 ◽  
Vol 28 (2) ◽  
pp. 339-350 ◽  
Author(s):  
E.M. Sparrow ◽  
S.S. Kang
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Cross Flow ◽  
Flow Tube ◽  
Tube Banks

Numerical Study of Fluid Flow and Heat Transfer Enhancement of Nanofluids over Tube Bank

2013 ◽  
Vol 388 ◽  
pp. 149-155 ◽  
Author(s):  
Mazlan Abdul Wahid ◽  
Ahmad Ali Gholami ◽  
H.A. Mohammed
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Heat Transfer Rate ◽  
Transfer Rate ◽  
Cross Flow ◽  
Bulk Temperature ◽  
Compact Heat Exchanger ◽  
Pure Fluid ◽  
Tube Banks

In the present work, laminar cross flow forced convective heat transfer of nanofluid over tube banks with various geometry under constant wall temperature condition is investigated numerically. We used nanofluid instead of pure fluid ,as external cross flow, because of its potential to increase heat transfer of system. The effect of the nanofluid on the compact heat exchanger performance was studied and compared to that of a conventional fluid.The two-dimensional steady state Navier-Stokes equations and the energy equation governing laminar incompressible flow are solved using a Finite volume method for the case of flow across an in-line bundle of tube banks as commercial compact heat exchanger. The nanofluid used was alumina-water 4% and the performance was compared with water. In this paper, the effect of parameters such as various tube shapes ( flat, circle, elliptic), and heat transfer comparison between nanofluid and pure fluid is studied. Temperature profile, heat transfer coefficient and pressure profile were obtained from the simulations and the performance was discussed in terms of heat transfer rate and performance index. Results indicated enhanced performance in the use of a nanofluid, and slight penalty in pressure drop. The increase in Reynolds number caused an increase in the heat transfer rate and a decrease in the overall bulk temperature of the cold fluid. The results show that, for a given heat duty, a mas flow rate required of the nanofluid is lower than that of water causing lower pressure drop. Consequently, smaller equipment and less pumping power are required.

Tube Banks Heat Transfer Enhancement Using Conical Fins

2010 ◽  
Author(s):  
Ignacio Carvajal-Mariscal ◽  
Florencio Sanchez-Silva ◽  
Georgiy Polupan
Keyword(s):  
Heat Transfer ◽  
Heat Exchange ◽  
Pressure Drop ◽  
Finned Tube ◽  
Hot Water ◽  
Experimental Results ◽  
Tube Bank ◽  
Finned Tubes ◽  
Tube Banks ◽  
Annular Fins

In this work the heat transfer and pressure drop experimental results obtained in a two step finned tube bank with conical fins are presented. The tube bank had an equilateral triangle array composed of nine finned tubes with conical fins inclined 45 degrees in respect with the tube axis. The heat exchange external area of a single tube is approximately 0.07 m2. All necessary thermal parameters, inlet/outlet temperatures, mass flows, for the heat balance in the tube bank were determined for different air velocities, Re = 3400–18400, and one constant thermal charge provided by a hot water flow with a temperature of 80 °C. As a result, the correlations for the heat transfer and pressure drop calculation were obtained. The experimental results were compared against the analytical results for a tube bank with annular fins with the same heat exchange area. It was found that the proposed tube bank using finned tubes with conical fins shows an increment of heat transfer up to 58%.

Heat transfer and pressure drop in single rows of tubes in cross-flow

1992 ◽  
Vol 15 (4) ◽  
pp. 219-223 ◽  
Author(s):  
Michael Beziel ◽  
Karl Stephan
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Cross Flow

An Analytical Study of the Optimized Performance of an Impingement Heat Sink

2004 ◽  
Vol 126 (4) ◽  
pp. 528-534 ◽  
Author(s):  
S. B. Sathe ◽  
B. G. Sammakia
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Heat Sink ◽  
High Performance ◽  
Cross Flow ◽  
High Heat ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
High Heat Transfer ◽  
Flow Through

The results of a study of a new and unique high-performance air-cooled impingement heat sink are presented. An extensive numerical investigation of the heat sink performance is conducted and is verified by experimental data. The study is relevant to cooling of high-power chips and modules in air-cooled environments and applies to workstations or mainframes. In the study, a rectangular jet impinges on a set of parallel fins and then turns into cross flow. The effects of the fin thickness, gap nozzle width and fin shape on the heat transfer and pressure drop are investigated. It is found that pressure drop is reduced by cutting the fins in the central impingement zone without sacrificing the heat transfer due to a reduction in the extent of the stagnant zone. A combination of fin thicknesses of the order of 0.5 mm and channel gaps of 0.8 mm with appropriate central cutout yielded heat transfer coefficients over 1500 W/m2 K at a pressure drop of less than 100 N/m2, as is typically available in high-end workstations. A detailed study of flow-through heat sinks subject to the same constraints as the impingement heat sink showed that the flow-through heat sink could not achieve the high heat transfer coefficients at a low pressure drop.

Sign in / Sign up

Export Citation Format

Share Document