Resolved shear stress intensity coefficient and fatigue crack growth in large crystalsChen, Q. and Liu, H.W.Theor. Appl. Fract. Mech. Oct. 1988, 10, (2), 111–122

1989 ◽  
Vol 11 (3) ◽  
pp. 208-208
Keyword(s):  
Shear Stress ◽  
Fatigue Crack ◽  
Stress Intensity ◽  
Fatigue Crack Growth ◽  
Crack Growth ◽  
Intensity Coefficient ◽  
Stress Intensity Coefficient

Effective Modeling of Fatigue Crack Growth in Pipelines

2012 ◽  
Author(s):  
Steven J. Polasik ◽  
Carl E. Jaske
Keyword(s):  
Fatigue Crack ◽  
Stress Intensity ◽  
Fatigue Crack Growth ◽  
Fracture Mechanics ◽  
Crack Growth ◽  
Growth Models ◽  
Critical Parameters ◽  
Operating Pressure ◽  
Mechanics Model ◽  
Key Variables

Pipeline operators must rely on fatigue crack growth models to evaluate the effects of operating pressure acting on flaws within the longitudinal seam to set re-assessment intervals. In most cases, many of the critical parameters in these models are unknown and must be assumed. As such, estimated remaining lives can be overly conservative, potentially leading to unrealistic and short reassessment intervals. This paper describes the fatigue crack growth methodology utilized by Det Norske Veritas (USA), Inc. (DNV), which is based on established fracture mechanics principles. DNV uses the fracture mechanics model in CorLAS™ to calculate stress intensity factors using the elastic portion of the J-integral for either an elliptically or rectangularly shaped surface crack profile. Various correction factors are used to account for key variables, such as strain hardening rate and bulging. The validity of the stress intensity factor calculations utilized and the effect of modifying some key parameters are discussed and demonstrated against available data from the published literature.

Effect of Temperature on Fatigue Crack Growth in CPVC

2003 ◽  
Vol 125 (1) ◽  
pp. 71-77 ◽  
Author(s):  
Muhammad Irfan-ul-Haq ◽  
Nesar Merah
Keyword(s):  
Stress Intensity Factor ◽  
Fatigue Crack ◽  
Stress Intensity ◽  
Fatigue Crack Growth ◽  
Intensity Factor ◽  
Crack Growth ◽  
Effect Of Temperature ◽  
Stress Intensity Factor Range ◽  
Crack Growth Behavior ◽  
Different Temperatures

This study addresses the effect of temperature on fatigue crack growth (FCG) behavior of CPVC. FCG tests were conducted on CPVC SEN tensile specimens in the temperature range −10 to 70°C. These specimens were prepared from 4-in. injection-molded pipe fittings. Crack growth behavior was studied using LEFM concepts. The stress intensity factor was modified to include the crack closure and plastic zone effects. The effective stress intensity factor range ΔKeff gave satisfactory correlation of crack growth rate (da/dN) at all temperatures of interest. The crack growth resistance was found to decrease with temperature increase. The effect of temperature on da/dN was investigated by considering the variation of mechanical properties with temperature. Master curves were developed by normalizing ΔKeff by fracture strain and yield stress. All the da/dN-ΔK curves at different temperatures were collapsed on a single curve. Crazing was found to be the dominant fatigue mechanism, especially at high temperature, while shear yielding was the dominant mechanism at low temperatures.

Mechanisms of Fatigue Crack Growth in WC-Co Cemented Carbides

2005 ◽  
Vol 297-300 ◽  
pp. 1120-1125 ◽  
Author(s):  
Myung Hwan Boo ◽  
Chi Yong Park
Keyword(s):  
Growth Rate ◽  
Stress Intensity Factor ◽  
Fatigue Crack ◽  
Stress Intensity ◽  
Fatigue Crack Growth ◽  
Intensity Factor ◽  
Crack Growth ◽  
Stress Ratio ◽  
Cemented Carbides ◽  
Stress Intensity Factor Range

In order to study the influence of stress ratio and WC grain size, the characteristics of fatigue crack growth were investigated in WC-Co cemented carbides with two different grain sizes of 3 and 6 µm. Fatigue crack growth tests were carried out over a wide range of fatigue crack growth rates covering the threshold stress intensity factor range DKth. It was found that crack growth rate da/dN against stress intensity factor range DK depended on stress ratio R. The crack growth rate plotted in terms of effective stress intensity factor range DKeff still exhibited the effect of microstructure. Fractographic examination revealed brittle fracture at R=0.1 and ductile fracture at R=0.5 in Co binder phase. The amount of Co phase transformation for stress ratio was closely related to fatigue crack growth characteristics.

Numerical Determination of Paris Law Constants for Carbon Steel Using a Two-Scale Model

2022 ◽  
pp. 1-15
Author(s):  
M. Mlikota
Keyword(s):  
Growth Rate ◽  
Stress Intensity Factor ◽  
Fatigue Crack ◽  
Stress Intensity ◽  
Fatigue Crack Growth ◽  
Crack Growth ◽  
Scale Model ◽  
Numerical Determination ◽  
Paris Law

For most engineering alloys, the long fatigue crack growth under a certain stress level can be described by the Paris law. The law provides a correlation between the fatigue crack growth rate (FCGR or da/dN), the range of stress intensity factor (ΔK), and the material constants C and m. A well-established test procedure is typically used to determine the Paris law constants C and m, considering standard specimens, notched and pre-cracked. Definition of all the details necessary to obtain feasible and comparable Paris law constants are covered by standards. However, these cost-expensive tests can be replaced by appropriate numerical calculations. In this respect, this paper deals with the numerical determination of Paris law constants for carbon steel using a two-scale model. A micro-model containing the microstructure of a material is generated using the Finite Element Method (FEM) to calculate the fatigue crack growth rate at a crack tip. The model is based on the Tanaka-Mura equation. On the other side, a macro-model serves for the calculation of the stress intensity factor. The analysis yields a relationship between the crack growth rates and the stress intensity factors for defined crack lengths which is then used to determine the Paris law constants.

Sign in / Sign up

Export Citation Format

Share Document