Comparison study on portable wind tunnel system and isolation chamber for determination of VOCs from areal sources

1996 ◽  
Vol 34 (3-4) ◽  
1996 ◽  
Vol 34 (3-4) ◽  
pp. 583-589 ◽  
Author(s):  
Kaiyun Jiang ◽  
Ralph Kaye

Many environmental monitoring programmes require the determination of volatile organic compounds (VOCs) emitted from large areal sources including liquid surfaces. A study was carried out to compare existing sampling techniques. Both the isolation chamber method (static technique) and the wind tunnel method (dynamic technique) were examined. A review of the mechanisms suggested that static techniques would not be appropriate for determining emissions from liquid surfaces which result from gas phase controlled volatilisation processes. A portable wind tunnel developed at the University of New South Wales and an isolation chamber built to USEPA specification were used in an experimental study of emissions from aqueous liquid surfaces. An acetone solution was chosen to represent gas phase controlled volatilisation processes. Toluene and methyl ethyl ketone in aqueous solution were chosen, respectively to investigate (1) liquid phase controlled volatilisation processes, and (2) combined gas and liquid phase controlled volatilisation processes. It was found that the use of the isolation chamber method resulted in different degrees of underestimation of the emission rates for the above three compounds. The wind tunnel method is suitable for sampling all VOC emissions from areal sources.


2014 ◽  
Vol 45 (1) ◽  
pp. 3-20 ◽  
Author(s):  
Ivan Vladimirovich Egorov ◽  
Boris Evgen'evich Zhestkov ◽  
Vladimir Viktorovich Shvedchenko

2020 ◽  
Vol 5 (10) ◽  
pp. 1274-1280
Author(s):  
Alfred Gift Mwachugha ◽  
Jean Byiringiro ◽  
Harrison Ngetha ◽  
Thomas Carolus ◽  
Kathrin Stahl

A Prandtl probe is one of the standard instruments used for flow characterization in wind tunnel facilities. The convectional fabrication method of this instrument requires skilled artisanship, precision drilling, lathing and soldering of its several parts. This reflects into high costs of production in turn making wind energy studies expensive. With the adoption of additive manufacturing, the tooling costs, skills required and design to manufacture constraints can be addressed. This research presents a Prandtl probe that was designed using NX™ software, fabricated by desktop stereolithography additive manufacturing platform and validated in a wind tunnel for velocity range of 0 m/s to 51 m/s. This research attested the option of fabricating relatively cheap functional Prandtl probe with desktop stereolithography technology which can be used for accurate determination of flow quality in wind tunnels experiments. This provides various learning and research institution in developing countries that have already invested in additive desktop manufacturing technology certainty and a cheaper option to fabricate wind research instruments for use at their laboratories. Moreover, fabrication and validation of a 5-hole Prandtl probe can also be examined.


2019 ◽  
Vol 9 (8) ◽  
Author(s):  
Siroos Karimzadeh ◽  
Mohammad Mehdi Taghizadeh

Abstract Determination of the high potential of dust emission is a requisite affair in the management of dusts emission and as well as avoiding its risks. Wind tunnel is among the most important approaches in the study of areas having high potential in emitting dusts. Extensive dried playas and desert areas require the making of low-cost, simple, and car-portable tunnels capable of presenting comparable data of various areas even supposing not having enough precision in the model of real wind motion. In this study, we first engaged in making a car-portable tunnel with a primarily semicircle section of 38 cm height, 50 cm diameter, and 110 cm length. A fan and key appliance with the ability to change speed were used along with a simple transformer launched with car battery. Then, concentration of the pm10 dusts was measured in the various wind speeds of 1, 2.5, 4, 5.5, and 7 m/s by the help of anemometer and digital equipments. The study of Bakhtegan playa was done, as the methodology of handling with this tunnel, in 35 positions, and zoning of the results was performed via ArcGIS software. Depending on the destructibility of the shell by wind, the areas under study were categorized as low potential (34%), medium potential (37%), and high potential (29%) in emitting dusts. The results of zoning spotted the high-potential areas on the map. The usage of small tunnels, as in the present model, may be applied in order for the low-cost and fast studies of vast areas to the purpose of playas management.


2019 ◽  
Vol 186 (11) ◽  
Author(s):  
Yao Zhang ◽  
Lan Zhang ◽  
Luyang Wang ◽  
Guoqing Wang ◽  
Makoto Komiyama ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document