scholarly journals Elongated Cells Drive Morphogenesis in a Surface-Wrapped Finite-Element Model of Germband Retraction

2019 ◽  
Vol 117 (1) ◽  
pp. 157-169 ◽  
Author(s):  
W. Tyler McCleery ◽  
Jim Veldhuis ◽  
Monica E. Bennett ◽  
Holley E. Lynch ◽  
Xiaoyan Ma ◽  
...  
2018 ◽  
Author(s):  
W. T. McCleery ◽  
J. Veldhuis ◽  
G. W. Brodland ◽  
M. E. Bennett ◽  
M. S. Hutson

ABSTRACTDuring Drosophila embryogenesis, the germband first extends to curl around the posterior end of the embryo, and then retracts back; however, retraction is not simply the reversal of extension. At a tissue level, extension is coincident with ventral furrow formation, and at a cellular level, extension occurs via convergent cell neighbor exchanges in the germband while retraction involves only changes in cell shape. To understand how cell shapes, tissue organization and cellular forces drive germband retraction, we investigate this process using a whole-embryo, surface-wrapped cellular finite element model. This model represents two key epithelial tissues – amnioserosa and germband – as adjacent sheets of 2D cellular finite elements that are wrapped around an ellipsoidal 3D approximation of an embryo. The model reproduces the detailed kinematics of in vivo retraction by fitting just one free model parameter, the tension along germband cell interfaces; all other cellular forces are constrained to follow ratios inferred from experimental observations. With no additional parameter adjustments, the model also reproduces failures of retraction when amnioserosa cells are removed to mimic U-shaped mutants or laser-microsurgery experiments. Surprisingly, retraction in the model is robust to changes in cellular force values, but is critically dependent on starting from a configuration with highly elongated amnioserosa cells. Their extreme cellular elongation is established during the prior process of germband extension and is then used to drive retraction. The amnioserosa is the one tissue whose cellular morphogenesis is reversed in germband extension and retraction – serving as a store of morphological information that coordinates the forces needed to retract the germband back to its pre-extension position and shape. In this case, and perhaps more generally, cellular force strengths are less important than the carefully established cell shapes that direct them.


1989 ◽  
Vol 17 (4) ◽  
pp. 305-325 ◽  
Author(s):  
N. T. Tseng ◽  
R. G. Pelle ◽  
J. P. Chang

Abstract A finite element model was developed to simulate the tire-rim interface. Elastomers were modeled by nonlinear incompressible elements, whereas plies were simulated by cord-rubber composite elements. Gap elements were used to simulate the opening between tire and rim at zero inflation pressure. This opening closed when the inflation pressure was increased gradually. The predicted distribution of contact pressure at the tire-rim interface agreed very well with the available experimental measurements. Several variations of the tire-rim interference fit were analyzed.


1996 ◽  
Vol 24 (4) ◽  
pp. 339-348 ◽  
Author(s):  
R. M. V. Pidaparti

Abstract A three-dimensional (3D) beam finite element model was developed to investigate the torsional stiffness of a twisted steel-reinforced cord-rubber belt structure. The present 3D beam element takes into account the coupled extension, bending, and twisting deformations characteristic of the complex behavior of cord-rubber composite structures. The extension-twisting coupling due to the twisted nature of the cords was also considered in the finite element model. The results of torsional stiffness obtained from the finite element analysis for twisted cords and the two-ply steel cord-rubber belt structure are compared to the experimental data and other alternate solutions available in the literature. The effects of cord orientation, anisotropy, and rubber core surrounding the twisted cords on the torsional stiffness properties are presented and discussed.


Sign in / Sign up

Export Citation Format

Share Document