Influence of pyrolytic carbon interphase and pyrolysis temperature on the mechanical and tribological properties of Cf/SiC after heat treatment at 1800 °C

2021 ◽  
Vol 47 (11) ◽  
pp. 16282-16293
Author(s):  
Chen Zhang ◽  
Yang Zhou ◽  
Hongrui Liu ◽  
Junping Li ◽  
Kefei Lu ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Tribological Properties ◽  
Pyrolysis Temperature ◽  
Pyrolytic Carbon ◽  
Mechanical And Tribological Properties

scholarly journals The effect of heat treatment on the mechanical and tribological properties of dual size SiC reinforced A357 matrix composites

2020 ◽  
Vol 9 (3) ◽  
pp. 6434-6452
Author(s):  
Avinash Lakshmikanthan ◽  
Ram Prabhu T. ◽  
Sai Babu Udayagiri ◽  
Praveennath G. Koppad ◽  
Manoj Gupta ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Tribological Properties ◽  
Matrix Composites ◽  
Mechanical And Tribological Properties

Influence of thermal cycling modes on VK8 hard alloy mechanical and tribological properties

2020 ◽  
pp. 55-65
Author(s):  
S. I. Bogodukhov ◽  
E. S. Kozik ◽  
E. V. Svidenko
Keyword(s):  
Heat Treatment ◽  
Solid Solution ◽  
Wear Resistance ◽  
Thermal Cycling ◽  
Hard Alloy ◽  
Tribological Properties ◽  
High Speed ◽  
Metal Cutting ◽  
Hard Alloys ◽  
Mechanical And Tribological Properties

Hard alloys are popular materials widely used in the toolmaking industry. Refractory carbides included in their composition make carbide tools very hard (80 to 92 HRA) and heat-resistant (800 to 1000 °С) so as they can be used at cutting speeds several times higher than those used for high-speed steels. However, hard alloys differ from the latter by lower strength (1000 to 1500 MPa) and the absence of impact strength, and this constitutes an urgent problem. We studied the influence of thermal cycling modes on the mechanical and tribological properties of VK8 (WC–8Co) hard alloy used in the manufacture of cutters and cutting inserts for metal working on metal-cutting machines. As the object of study, we selected 5×5×35 mm billets made of VK8 (WC–8Co) alloy manufactured by powder metallurgy methods at Dimitrovgrad Tool Plant. The following criteria were selected for heat treatment mode evaluation: Vickers hardness, flexural strength, and mass wear resistance (as compared to the wear of asreceived samples that were not heat treated). Plates in the initial state and after heat treatment were subjected to abrasion tests. Wear results were evaluated by the change in the mass of plates. Regularities of the influence of various time and temperature conditions of heat treatment on the tribological properties of products made of VK group tungsten hard alloys were determined. An increase in the number of thermal cycling cycles improved such mechanical properties of the VK8 hard alloy as strength and hardness. When repeating the cycles five times, an increase in abrasive wear resistance was obtained compared to the initial nonheat-treated sample. The elemental composition of the VK8 hard alloy changed insignificantly after thermal cycling, only a slight increase in oxygen was observed on the surface of plates. The grain size after thermal cycling increased in comparison with the initial VK8 hard alloy. It was found that VK8 hard alloy thermocyclic treatment leads to a change in the phase composition. X-ray phase analysis showed the presence of a large amount of α-Co with an hcp-type lattice on the surface of a hard alloy and a solid solution of WC in α-Co. A change in the cobalt modification ratio causes a decrease in microstresses. An analysis of the carbide phase structure state showed that the size of crystallites and microstresses changed after thermal cycling. The lattice constant of the cobalt cubic solid solution decreased, which may indicate a decrease in the amount of tungsten carbide and carbon dissolved in it. Statistical processing of experimental results included the calculation of the average value of the mechanical property, its dispersion and standard deviation in the selected confidence interval.

scholarly journals Mechanical and Dry Sliding Wear Behaviour of Al6061/Gr MMCs and its Multi Response Optimization using Hybrid Fuzzy Grey Relational Technique

2019 ◽  
Vol 9 (2) ◽  
pp. 1174-1183
Keyword(s):  
Heat Treatment ◽  
Tribological Properties ◽  
Sliding Wear ◽  
Wear Behaviour ◽  
Dry Sliding Wear ◽  
Wear Loss ◽  
Dry Sliding ◽  
T6 Heat Treatment ◽  
Mechanical And Tribological Properties ◽  
Grey Relational

An attempt is made to find the mechanical and tribological properties of Al6061/Gr metal matrix composites (MMC) produced using stir casting method. It is important to note that the certain components require high hardness and wear resistance to fulfil the functional requirements, the said properties of the MMCs influenced largely on the condition with which they are produced or treated. Therefore, in the present paper the composites are tested in two stages that is before T6 heat treatment and after T6 heat treatment respectively. The composites are made with Al6061 alloy as matrix and graphite with 3%, 6%, 9% and 12% by wt is considered as reinforcement. Once the composites are prepared, they are examined for their microstructural, mechanical, and tribological properties. Further, a response surface methodology (RSM) has been used to model the wear loss and coefficient of friction for both before and after T6 heat treatment of MMCs. The non-linear regression model obtained is validated both statistically and with the help of experimental test cases. The evidence of wear phenomenon has been observed with the help of Scanning Electron Microscopy (SEM). Further, fuzzy grey relational Technique has been used to determine the multi performance index for the dry sliding wear and friction phenomenon of the developed composite.

Sign in / Sign up

Export Citation Format

Share Document