Quality verification of polymer-modified asphalt binder used in hot-mix asphalt pavement construction

2017 ◽  
Vol 150 ◽  
pp. 157-166 ◽  
Author(s):  
Yuhong Wang ◽  
Dan Chong ◽  
Yong Wen
Keyword(s):  
Hot Mix Asphalt ◽  
Asphalt Pavement ◽  
Asphalt Binder ◽  
Modified Asphalt ◽  
Modified Asphalt Binder ◽  
Polymer Modified Asphalt ◽  
Pavement Construction

Polyacrylate Modified Binder for Sustainable Asphalt Pavement Performances Using Superpave Mix Design

2015 ◽  
Vol 747 ◽  
pp. 238-241
Author(s):  
Wan Adilah Ismail ◽  
Intan Rohani Endut ◽  
Sit Zaharah Ishak
Keyword(s):  
Material Selection ◽  
Asphalt Pavement ◽  
Asphalt Binder ◽  
Binder Content ◽  
Mix Design ◽  
Asphalt Binders ◽  
Air Voids ◽  
Modified Asphalt ◽  
Modified Asphalt Binder ◽  
Pavement Construction

Sustainable asphalt pavement is important in decreasing material costs by improving the existing material such as modified asphalt binders. It is also needed to provide a quality riding for road users. In achieving quality riding, the material selection and mix design must be correctly examined before using in pavement construction. Then, the aims of this study are to determine suitability of material selected by examining the aggregate properties and modified asphalt binder. In modified asphalt binder, 6% of polyacrylate polymer was added as an additive in 500g of binder content to dissolve. It was checked through Superpave gyratory compactor in determining air voids samples in term of height after compacted. The samples were mixed with different percentages of binder content; 5%, 5.5%, 6% and 6.5% to produce control and polyacrylate modified samples. 8 gyratory for Ninitialand 100 gyratory for Ndesignwere used in compaction of samples to determine air voids in term of height. The results show that 5.5% of binder content of polyacrylate modified samples has lower air voids compare than control samples. Thus, modified binders are able to minimize binder usage and save natural sources and also cost by improving bonding between mixtures to prevent pavement failure

Highly Modified Asphalt Binder for Asphalt Crack Relief Mix

2017 ◽  
Vol 2630 (1) ◽  
pp. 110-117 ◽  
Author(s):  
Matheus S. Gaspar ◽  
Kamilla L. Vasconcelos ◽  
Amanda H. M. da Silva ◽  
Liedi L. B. Bernucci
Keyword(s):  
Hot Mix Asphalt ◽  
Asphalt Binder ◽  
Asphalt Mixture ◽  
Bending Test ◽  
Asphalt Binders ◽  
Reflective Cracking ◽  
Modified Asphalt ◽  
Asphalt Overlay ◽  
Modified Asphalt Binder ◽  
Styrene Butadiene

Reflective cracking is a common issue with respect to rehabilitated asphalt pavements, especially when the rehabilitation is done by applying a hot-mix asphalt overlay on the existing damaged pavement. Several approaches can be adopted to delay reflective cracking. They include an increase of the overlay thickness and the use of a stress relief asphalt mixture (SRAM), which is a fine-graded, flexible, and thin asphalt interlayer. Because the efficiency of a SRAM is highly related to the properties of the asphalt binder used in the mixture, it is of interest to use a highly modified asphalt (HiMA) binder. This paper describes a field test comprising three sections at BR-116 (a heavily trafficked highway in Brazil). One of the rehabilitation strategies used for a cracked asphalt pavement was a 2.5-cm SRAM (produced with a HiMA binder) and 5-cm styrene–butadiene–styrene (SBS) hot-mix asphalt (HMA). The other two strategies were to apply SBS HMA overlays of different thicknesses (7.5 cm and 10.5 cm). The aim was to evaluate and compare the capability of these solutions to control reflective cracking. Rheological properties and multiple stress creep and recovery tests were performed on the asphalt binders, and the semicircular bending test was performed on the asphalt mixtures. The surface conditions were monitored, and the results for each section were compared. After a 29-month period, the section that received the interlayer had the lowest cracked area and showed better resistance than the overlays did to reflective cracking and better maintenance of the original thickness of the pavement.

Nonlinear Viscoelastic Response of Crumb Rubber Modified Asphalt Binder Under Large Strains

2020 ◽  
Vol 2674 (3) ◽  
pp. 139-149
Author(s):  
Saqib Gulzar ◽  
B. Shane Underwood
Keyword(s):  
Asphalt Binder ◽  
Crumb Rubber ◽  
Oscillatory Shear ◽  
Asphalt Binders ◽  
Large Strains ◽  
Viscoelastic Response ◽  
Modified Asphalt ◽  
Nonlinear Viscoelastic ◽  
Modified Asphalt Binder ◽  
Polymer Modified Asphalt

Agencies have been increasing their use of polymer modified asphalt binders in recent years to address performance issues and lengthen the useful life of their pavements. When deployed these materials likely experience strain levels exceeding their linear viscoelastic (LVE) limits. The same situation exists in non-polymer modified asphalt binders as well, but the effect may be more pronounced in polymer modified systems because of their bi-phasic nature. In this study, terminally blended crumb rubber (CR-TB) modified asphalt is studied to understand and quantify the nonlinear viscoelastic response under large strains. The CR-TB binders are extensively used in pavements subjected to high vehicular loads and extreme climatic conditions; thereby, their response under large strains becomes more critical. The current standard characterization techniques are based on LVE response using small amplitude oscillatory shear rheology only and do not consider the behavior of binders under large strains. In this study, large amplitude oscillatory shear (LAOS) rheology is used as a framework to more thoroughly investigate the complete response of the CR-TB modified asphalt binder under large strains at 30°C, 40°C, 50°C, and 60°C and at the frequencies of 0.5, 1, and 5 Hz. The LAOS response is analyzed using Fourier-transform rheology and the orthogonal stress decomposition method involving Chebyshev polynomial representation. It is found that nonlinearity manifests greatly in this study material as strain levels increase and frequencies decrease. The relative nonlinearity increases with increasing strain amplitude and is more significant towards lower end of the tested temperature range. The CR-TB binder shows strain-stiffening/softening and shear-thinning/thickening behavior depending upon a specific temperature, strain level, and frequency.

Effect of Antioxidant Characteristic from Waste Cooking Oil in Modified Asphalt Binder

2016 ◽  
Vol 700 ◽  
pp. 197-206 ◽  
Author(s):  
Wan Nur Aifa Wan Azahar ◽  
Mastura Bujang ◽  
Ramadhansyah Putra Jaya ◽  
Mohd Rosli Hainin ◽  
Norzita Ngadi ◽  
...  
Keyword(s):  
Aging Process ◽  
Asphalt Pavement ◽  
Asphalt Binder ◽  
Waste Cooking Oil ◽  
Short Term ◽  
Aging Rate ◽  
Modified Asphalt ◽  
Cooking Oil ◽  
Modified Asphalt Binder

Aging process especially in asphalt binder material can occur throughout the life cycle of asphalt pavement starting from mixing, placement and during the service life. During this process, the more stiffer and brittle of asphalt binder is produced due to age hardening and gives an indication of initial factor of deterioration in asphalt pavement. A number of noteworthy researchers have focused on oil based modification to produce modified asphalt binder by using Waste Cooking Oil (WCO), due to the presence of natural antioxidant properties possessed in WCO. Antioxidant has played the role as an oxidative inhibition and has the potential to minimize the aging rate to occur. The aging process is conducted by separating between short term and long term aging where short term oxidative aging of binders was simulated using rolling thin film oven (RTFO) while long term aging was performed using pressure aging vessel (PAV). The laboratory evaluation was carried out to investigate the relationship between the qualities of WCO that affect the availability of antioxidant amount towards the susceptibility of aging rate by conducting Dynamic Shear Rheometer (DSR). The result from rheological studies demonstrated that the lowest Aging Index (AI) is presented as 2.14, 2.18 and 1.79 for replacement by using WCO in December sample at concentration of 3%, 4% and 5% for short term aging while AI at 3% = 5.17 and 5% = 7.22 for long term aging. Therefore, the high quality of oil represented by WCO in December sample has indicated the high availability of antioxidant content that can minimize the aging susceptibility in the asphalt binder modified by WCO.

A Review of Advance Nanotechnology against Pavement Deterioration

2015 ◽  
Vol 1113 ◽  
pp. 9-12 ◽  
Author(s):  
C.M. Nurulain ◽  
P.J. Ramadhansyah ◽  
A.H. Norhidayah
Keyword(s):  
New Technology ◽  
Permanent Deformation ◽  
Asphalt Binder ◽  
Construction Materials ◽  
Fatigue Cracking ◽  
Asphalt Pavements ◽  
X Ray Diffraction ◽  
Modified Asphalt ◽  
Modified Asphalt Binder ◽  
Polymer Modified Asphalt

This paper presents a review of nanoclay as a latest technology in order to overcome problem due deterioration such as rutting, fatigue, stripping, cracking and so on. Nowadays, with increasing of traffic volume and heavy vehicle conditions of existing road totally fail in order to accommodate this situation during design period. In order to manage this problem the new technology had been create and apply. Previous researches prove that nanotechnology has potential solution to enhance the performance and durability of construction materials. Material properties were characterized using Fourier-transform infrared spectroscopy (FTIR), field emission scanning electron microscopy (FESEM) and X-ray diffraction (XRD). According to previous research there were proved that addition of nanoclay lead great improvements on permanent deformation and fatigue life of hot mix asphalt (HMA). In addition the overall performance of nanoclay as polymer modified asphalt binder was improve in terms of rutting and fatigue cracking resistance compare to non-modified asphalt binder. Therefore, nanoclay itself would be an alternative as modifier to use in the bitumen to improve the lifetime of asphalt pavements.

Sign in / Sign up

Export Citation Format

Share Document