Study Investigating the Influence of Warm-Mix Asphalt Additives on Rutting and Fatigue Performance of Nano-Modified Asphalt Binders

The current study investigates the synergized effect of a nanomaterial and two warm mix additives asphalt (WMA) additives on different properties of asphalt binders. The study used an optimal percentage of 2% for nano-Al2O3; two WMA additives were used in different concentrations. The results revealed that the addition of WMA additives increased the softening point of nano-Al2O3 modified asphalt binder. Penetration and ductility results showed a decrease after the introduction of WMA additives. The viscosity of nano-Al2O3 modified asphalt binders showed a reduction after the introduction of WMA additives. Rutting evaluation was done by using the superpave rutting parameter and multiple stress creep and recovery (MSCR) test. The fatigue performance of the asphalt binders was measured using the superpave fatigue parameter and linear amplitude sweep (LAS) test. Results showed that the introduction of WMA additives improved the rutting and fatigue performance of nano-Al2O3 modified asphalt binders. The introduction of WMA additives enhanced the aging performance of the nano-Al2O3 modified asphalt binders.

Multiple Stress Creep Recovery (MSCR) Test for Determination of Waste Engine Oil Modified Asphalt Binder as Pavement Material

Engineers have been using modified binders to improve the quality of flexible pavements. The use of waste material is one of the solutions taken in this direction. It is for this ground that the studies emphasis on the evaluation of waste engine oil as a modifier for asphalt binder as a pavement material. In the study uses four samples extracted from 80/100 penetration grade bitumen. From four sample first sample was checked for weather requirements of asphalt binder meet or not and the three were modified with different content of engine oil (3,6 and 9%). The behaviors of both unmodified and modified binder were checked for rheological properties. Dynamic shear rheometer (DSR) was used to determine high temperature performance grade (PG) and multiple stress creep recovery tests to determine rutting resistance properties of the binder. PG analysis indicates that both aged and un-aged 3% and 6% modified binder have similar higher PG grade with the unmodified one and 9% modified to have lower PG vale. Jnr3.2 value of modified asphalt binder is lower than unmodified binder indicating that modification had improved the rutting resistance and design traffic load (ESALS). The study shows that it is possible to use waste engine oil-modified binder as a pavement material.

Evaluation of Susceptibility of Asphalt Binders to Rutting through MSCR Test

Using modified asphalt binder is one of the most effective methods to solve the rutting problem of asphalt pavement, but the traditional G ∗ / sin δ parameter is not enough to characterize the rutting resistance of modified asphalt in field use. In order to accurately evaluate the high temperature performance of asphalt and establish the relationship between the rutting resistance of binder and mixture, two kinds of matrix asphalt and three kinds of modified asphalt were selected for DSR and MSCR tests. G ∗ / sin δ , nonrecoverable creep compliance Jnr, recovery rate R, and other parameters were used to characterize the permanent deformation resistance of the binder, and the correlation between these parameters and the results of rutting test was analyzed. The results show that Jnr3.2 can accurately characterize the permanent deformation resistance of asphalt, while the stress sensitivity index Jnrdiff is not applicable to all types of modified asphalt. In contrast, Jnrslope can better reflect the stress sensitivity of asphalt, and Jnrslope is significantly correlated with the results of rutting test.

Evaluation of High-Temperature and Low-Temperature Performances of Lignin–Waste Engine Oil Modified Asphalt Binder and Its Mixture

This research aims to explore the high-temperature and low-temperature performances of lignin–waste engine oil-modified asphalt binder and its mixture. For this research, the lignin with two contents (4%, 6%) and waste engine oil with two contents (3%, 5%) were adopted to modify the control asphalt binder (PG 58-28). The high-temperature rheological properties of the lignin–waste engine oil-modified asphalt binder were investigated by the viscosity obtained by the Brookfield viscometer and the temperature sweep test by the dynamic shear rheometer. The low-temperature rheological property of the lignin–waste engine oil-modified asphalt binder was evaluated by the stiffness and m-value at two different temperatures (−18 °C, −12 °C) obtained by the bending beam rheometer. The high-temperature and the low-temperature performances of the lignin–waste engine oil-modified asphalt mixture were explored by the rutting test and low-temperature bending beam test. The results displayed that the rotational viscosity and rutting factor improved with the addition of lignin and decreased with the incorporation of waste engine oil. Adding the lignin into the control asphalt binder enhanced the elastic component while adding the waste engine oil lowered the elastic component of the asphalt binder. The stiffness of asphalt binder LO60 could not meet the requirement in the specification, but the waste engine oil made it reach the requirement based on the bending beam rheometer test. The waste engine oil could enhance the low-temperature performance. The dynamic stabilities of LO40- and LO60-modified asphalt mixture increased by about 9.05% and 17.41%, compared to the control mixture, respectively. The maximum tensile strain of LO45 and LO65 increased by 16.39% and 25.28% compared to that of LO40 and LO60, respectively. The high- and low-temperature performances of the lignin–waste engine oil-modified asphalt LO65 was higher than that of the control asphalt. The dynamic stability had a good linear relationship with viscosity, the rutting factor of the unaged at 58 °C, and the rutting factor of the aged at 58 °C, while the maximum tensile strain had a good linear relationship with m-value at −18 °C. This research provides a theoretical basis for the further applications of lignin–waste engine oil-modified asphalt.