A real-time control-oriented discrete nonlinear model development for in-cylinder air charge, residual gas and temperature prediction of a Gasoline Direct Injection engine using cylinder, intake and exhaust pressures

2022 ◽  
Vol 119 ◽  
pp. 104978
Author(s):  
Amir Khameneian ◽  
Xin Wang ◽  
Paul Dice ◽  
Jeffrey D. Naber ◽  
Mahdi Shahbakhti ◽  
...  
2017 ◽  
Vol 51 (24) ◽  
pp. 14233-14243 ◽  
Author(s):  
Michael Chys ◽  
Wim T. M. Audenaert ◽  
Emma Deniere ◽  
Séverine Thérèse F. C. Mortier ◽  
Herman Van Langenhove ◽  
...  

1999 ◽  
Vol 39 (2) ◽  
pp. 159-168 ◽  
Author(s):  
J. Milina ◽  
S. Sægrov ◽  
J. Lei ◽  
A. König ◽  
O. Nilssen ◽  
...  

This paper describes some results of an integrated model development and its application to the Høvringen wastewater system in Trondheim, Norway. Major model development needs concern the integration of sewage production, transport and treatment simulation, the interface with existing databases and the possibility of simulating processes that are controlled in real time. The developed integrated model has been used to design the treatment process as well as static and dynamic measures in both the catchment and the sewer system. These measures include extended pumping, adjustment of overflows, separation of storm water runoff from “non-effective separate systems”, retention and real-time control of the sewer tunnel volume.


2011 ◽  
Vol 347-353 ◽  
pp. 2504-2510 ◽  
Author(s):  
Yuh Yih Wu ◽  
Bo Chiuan Chen ◽  
Anh Trung Tran

The Semi-Direct Injection (SDI) system has been shown to improve small engine efficiency and exhaust by utilizing a lean burn method. In order to better understand how to more readily utilize the control systems in SDI engine, the real-time operation of an SDI engine was modeled. A charging model was developed by using a filling-and-emptying model to simulate air exchange in an engine, including varying the intake manifold structure. A single-zone model was applied to a combustion model and the effects of air/fuel ratio and swirl ratio on combustion duration were also considered. The calculated results of the intake manifold pressure, heat release rate, and cylinder pressure were compared with the experimental data. The results of this study show that this modeling process approximates reality.


2020 ◽  
Vol 10 (17) ◽  
pp. 6034 ◽  
Author(s):  
Kegang Zhao ◽  
Chengxia Wang ◽  
Guoquan Xiao ◽  
Haolin Li ◽  
Jie Ye ◽  
...  

The autonomous driving is rapid developing recently and model predictive controls (MPCs) have been widely used in unmanned vehicle trajectory tracking. MPCs are advantageous because of their predictive modeling, rolling optimization, and feedback correction. In recent years, most studies on unmanned vehicle trajectory tracking have used only linear model predictive controls to solve MPC algorithm shortcomings in real time. Previous studies have not investigated problems under conditions where speeds are too fast or trajectory curvatures change rapidly, because of the poor accuracy of approximate linearization. A nonlinear model predictive control optimization algorithm based on the collocation method is proposed, which can reduce calculation load. The algorithm aims to reduce trajectory tracking errors while ensuring real-time performance. Monte Carlo simulations of the uncertain systems are carried out to analyze the robustness of the algorithm. Hardware-in-the-loop simulation and actual vehicle experiments were also conducted. Experiment results show that under i7-8700, the calculation time is less than 100 ms, and the mean square error of the lateral deviation is maintained at 10−3 m2, which proves the proposed algorithm can meet the requirement of real time and accuracy in some particular situations. The unmanned vehicle trajectory tracking method provided in this article can meet the needs of real-time control.


Author(s):  
Nikhil Ravi ◽  
Matthew J. Roelle ◽  
J. Christian Gerdes

This paper presents experimental cycle-by-cycle control of a single cylinder HCCI engine. The controller is developed from a discrete-time nonlinear model presented in previous work. The model captures the behavior of a gasoline direct-injection engine with an exhaust-recompression strategy used to achieve HCCI. This model is linearized about an operating point so as to enable the synthesis of linear controllers. The model states are represented by the temperature and oxygen content of the retained exhaust, and so are not measurable in practice. Therefore, an observer is used to estimate the states based on a measured ignition proxy. The state estimates are then used by a reference-input tracking controller to track a desired system trajectory. Experimental results show tracking of the model outputs that is comparable to tracking achieved in simulation. The controller is also seen to reduce the cycle-to-cycle variability of combustion significantly, particularly at later combustion phasing. This stabilizes combustion, lowers the instances of misfires, and enables steady operation at points that are normally unstable.


1984 ◽  
Vol 16 (5-7) ◽  
pp. 419-434
Author(s):  
Hilary Dexter ◽  
James Petch

This paper deals with the problems of using the River Jordan as a source of irrigation water for agricultural settlements in the area between Lake Kinneret and the Dead Sea. The river is polluted by chlorides from salt springs and the levels are very variable. A forecasting model for chlorides is proposed which will operate with a real-time system in order to minimize loads applied to crops. The Box-Jenkins methodology is shown to provide a suitable model with the severe constraints of data availability. The statistical and operational success of the model are examined for forecasts at one abstraction point on the Jordan. Model development continues.


Sign in / Sign up

Export Citation Format

Share Document