Corrosion behaviour of Fe-25Cr alloy in wet CO2 gas at 650 °C: Effects of chloride deposits and Si+Mn alloying addition

2022 ◽  
Vol 195 ◽  
pp. 110001
Author(s):  
Yuchen Cai ◽  
Thuan Dinh Nguyen ◽  
Jianqiang Zhang ◽  
Brian Gleeson ◽  
David J. Young
Keyword(s):  
Corrosion Behaviour ◽  
Co2 Gas

Effects of Sulphate Deposits on Corrosion Behaviour of Fe-Based Alloys in Wet CO2 Gas at 750 °C

2020 ◽  
Author(s):  
Yun Xie ◽  
Yuchen Cai ◽  
Jianqiang Zhang ◽  
Brian Gleeson ◽  
David J. Young
Keyword(s):  
Corrosion Behaviour ◽  
Co2 Gas

Effects of sulphate deposits on corrosion behaviour of Ni-base alloys in wet CO2 gas at 750 °C

2021 ◽  
Vol 181 ◽  
pp. 109227
Author(s):  
Yun Xie ◽  
Yuchen Cai ◽  
Jianqiang Zhang ◽  
Brian Gleeson ◽  
David J. Young
Keyword(s):  
Corrosion Behaviour ◽  
Co2 Gas

Effect of Hydrogen Chloride on Corrosion Behaviour of Fe–Cr Alloys in Wet CO2 Gas at 650 °C

2020 ◽  
Vol 94 (1-2) ◽  
pp. 51-80 ◽  
Author(s):  
Khaing Khaing Aye ◽  
Jianqiang Zhang ◽  
David J. Young
Keyword(s):  
Hydrogen Chloride ◽  
Corrosion Behaviour ◽  
Co2 Gas

Role of Aluminium on the Microstructure and Corrosion Behaviour of Magnesium Prepared by Powder Metallurgy Method

2020 ◽  
Vol 17 (3) ◽  
pp. 8206-8213
Author(s):  
J. Alias
Keyword(s):  
Corrosion Resistance ◽  
Powder Metallurgy ◽  
Corrosion Behaviour ◽  
Corrosion Current ◽  
Optical Microscope ◽  
High Reactivity ◽  
Aluminium Content ◽  
Powder Metallurgy Method ◽  
X Ray Diffraction ◽  
Promising Development

Much research on magnesium (Mg) emphasises creating good corrosion resistance of magnesium, due to its high reactivity in most environments. In this study, powder metallurgy (PM) technique is used to produce Mg samples with a variation of aluminium (Al) composition. The effect of aluminium composition on the microstructure development, including the phase analysis was characterised by optical microscope (OM), scanning electron microscopy (SEM) and x-ray diffraction (XRD). The mechanical property of Mg sample was performed through Vickers microhardness. The results showed that the addition of aluminium in the synthesised Mg sample formed distribution of Al-rich phases of Mg17Al12, with 50 wt.% of aluminium content in the Mg sample exhibited larger fraction and distribution of Al-rich phases as compared to the 20 wt.% and 10 wt.% of aluminium content. The microhardness values were also increased at 20 wt.% and 50 wt.% of aluminium content, comparable to the standard microhardness value of the annealed Mg. A similar trend in corrosion resistance of the Mg immersed in 3.5 wt.% NaCl solution was observed. The corrosion behaviour was evaluated based on potentiodynamic polarisation behaviour. The corrosion current density, icorr, is observed to decrease with the increase of Al composition in the Mg sample, corresponding to the increase in corrosion resistance due to the formation of aluminium oxide layer on the Al-rich surface that acted as the corrosion barrier. Overall, the inclusion of aluminium in this study demonstrates the promising development of high corrosion resistant Mg alloys.

Simulation of SLF Interrupting Performance for CO2 Gas Circuit Breaker based on Serially Connected 3 Arc Models

2010 ◽  
Vol 130 (10) ◽  
pp. 888-894
Author(s):  
Tadashi Koshizuka ◽  
Keisuke Udagawa ◽  
Takeshi Shinkai ◽  
Toshiyuki Uchii ◽  
Hiromichi Kawano
Keyword(s):  
Circuit Breaker ◽  
Co2 Gas

Influence of Carbon on the Hot Corrosion Behaviour of Fe-Base Alloys

1989 ◽  
Vol 30 (9) ◽  
pp. 707-716 ◽  
Author(s):  
A. U. Malik ◽  
M. Ishaq ◽  
Sharif Ahmad ◽  
Sultan Ahmad
Keyword(s):  
Hot Corrosion ◽  
Corrosion Behaviour

Corrosion Behaviour of Copper in Various Grades of Palm Oil

2008 ◽  
Vol 45 (7) ◽  
pp. 348-351
Author(s):  
Mohammed Misbahul Amin
Keyword(s):  
Palm Oil ◽  
Corrosion Behaviour
Sign in / Sign up

Export Citation Format

Share Document