scholarly journals Computational and Experimental Study of Heat Transfer on the heat sink with an impinging synthetic jet under Various Excitation Wave

2021 ◽  
pp. 101106
Author(s):  
Damora Rhakasywi ◽  
Harinaldi ◽  
Engkos A. Kosasih ◽  
Ridho Irwansyah
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Heat Sink ◽  
Synthetic Jet ◽  
Excitation Wave

Experimental and Numerical Study of Methanol-Water Mixture Single-Phase Heat Transfer in a Micro-Channel Heat Sink

2012 ◽  
Author(s):  
Chun K. Kwok ◽  
Matthew M. Asada ◽  
Jonathan R. Mita ◽  
Weilin Qu
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Heat Sink ◽  
Single Phase ◽  
Numerical Study ◽  
Pure Water ◽  
Molar Fraction ◽  
Water Mixture ◽  
Micro Channel ◽  
Numerical Predictions

This paper presents an experimental study of single-phase heat transfer characteristics of binary methanol-water mixtures in a micro-channel heat sink containing an array of 22 microchannels with 240μm × 630μm cross-section. Pure water, pure methanol, and five methanol-water mixtures with methanol molar fraction of 16%, 36%, 50%, 63% and 82% were tested. Key parametric trends were identified and discussed. The experimental study was complemented by a three-dimensional numerical simulation. Numerical predictions and experimental data are in good agreement with a mean absolute error (MAE) of 0.87%.

An experimental study on the flow and heat transfer of an impinging synthetic jet

2019 ◽  
Vol 144 ◽  
pp. 118626 ◽  
Author(s):  
Yang Xu ◽  
Chanhee Moon ◽  
Jin-Jun Wang ◽  
Oleg G. Penyazkov ◽  
Kyung Chun Kim
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Synthetic Jet ◽  
Flow And Heat Transfer

Heat Transfer Enhancement by Synthetic Jet Arrays in Air-Cooled Heat Sinks for Use in Electronics Cooling

2012 ◽  
Author(s):  
Longzhong Huang ◽  
Terrence Simon ◽  
Min Zhang ◽  
Youmin Yu ◽  
Mark North ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Channel Flow ◽  
Heat Sink ◽  
Jet Flow ◽  
Synthetic Jet ◽  
Synthetic Jets ◽  
Transfer Enhancement ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients

A synthetic jet is an intermittent jet which issues through an orifice from a closed cavity over half of an oscillation cycle. Over the other half, the flow is drawn back through the same orifice into the cavity as a sink flow. The flow is driven by an oscillating diaphragm, which is one wall of the cavity. Synthetic jets are widely used for heat transfer enhancement since they are effective in disturbing and thinning thermal boundary layers on surfaces being cooled. They do so by creating an intermittently-impinging flow and by carrying to the hot surface turbulence generated by breakdown of the shear layer at the jet edge. The present study documents experimentally and computationally heat transfer performance of an array of synthetic jets used in a heat sink designed for cooling of electronics. This heat sink is comprised of a series of longitudinal fins which constitute walls of parallel channels. In the present design, the synthetic jet flow impinges on the tips of the fins. In the experiment, one channel of a 20-channel heat sink is tested. A second flow, perpendicular to the jet flow, passes through the channel, drawn by a vacuum system. Surface- and time-averaged heat transfer coefficients for the channel are measured, first with just the channel flow active then with the synthetic jets added. The purpose is to assess heat transfer enhancement realized by the synthetic jets. The multiple synthetic jets are driven by a single diaphragm which, in turn, is activated by a piezoelectrically-driven mechanism. The operating frequency of the jets is 1250 Hz with a cycle-maximum jet velocity of 50 m/s, as measured with a miniature hot-film anemometer probe. In the computational portion of the present paper, diaphragm movement is driven by a piston, simulating the experimental conditions. The flow is computed with a dynamic mesh using the commercial software package ANSYS FLUENT. Computed heat transfer coefficients show a good match with experimental values giving a maximum difference of less than 10%. The effects of amplitude and frequency of the diaphragm motion are documented. Changes in heat transfer due to interactions between the synthetic jet flow and the channel flow are documented in cases of differing channel flow velocities as well as differing jet operating conditions. Heat transfer enhancement obtained by activating the synthetic jets can be as large as 300% when the channel flow is of a low velocity compared to the synthetic jet peak velocity (as low as 4 m/s in the present study).

An Experimental Study of Pin Fin Heat Sinks and Determination of End Wall Heat Transfer

2003 ◽  
Author(s):  
Massimiliano Rizzi ◽  
Ivan Catton
Keyword(s):  
Heat Transfer ◽  
Experimental Study ◽  
Heat Sink ◽  
Optimization Methods ◽  
Heat Sinks ◽  
Base Region ◽  
Transfer Coefficients ◽  
Media Type ◽  
Pin Fin ◽  
Heat Transfer Coefficients

An experimental study of a pin fin heat sink was carried out in support of the development of heat sink optimization methods requiring more detailed measurements be made. Measurements of heat flux and temperature are used to separately determine heat transfer coefficients for the pins and the base region between the pins. Three pitch to diameter ratios (distance from pin center to pin center measured diagonally) were studied: P/d = 3/1, 9/4, 3/2. Heat generation was accomplished using cartridge heaters inserted into a copper block. The high thermal conductivity of the copper ensured that the surface beneath the heat sink would be at a constant temperature. The cooling fluid was air and the experiments were conducted with a Reynolds numbers based on a porous media type hydraulic diameter ranging from 500 to 25000. The channel had a shroud that touches the fin tips, eliminating any flow bypass. The pin surface heat transfer coefficients match the values reported by Kays and London and by Zukauskas. The base region heat transfer coefficients were, surprisngly, larger than the pin values.

scholarly journals Performance of special type heat sink with an integrated synthetic jet actuator

2019 ◽  
Vol 100 ◽  
pp. 00017 ◽  
Author(s):  
Paweł Gil
Keyword(s):  
Heat Transfer ◽  
Heat Sink ◽  
Thermal Power ◽  
High Heat ◽  
Synthetic Jet ◽  
Industrial Environment ◽  
Synthetic Jet Actuator ◽  
Characteristic Temperatures ◽  
High Heat Transfer ◽  
High Heat Transfer Coefficient

The performance of special type heat sink with integrated synthetic jet actuator has been presented in this work. Synthetic jet is a flow technique which synthesizes stagnant air to a form of jet. Synthetic jet produces high turbulent flow and thus high heat transfer coefficient can be achieved. Standard heat sink with fan have limited applications in particular in a dusty industrial environment. Therefore, the use of new flow technique is optimistic. The paper presents preliminary results of heat sink thermal power and characteristic temperatures during synthetic jet switched on and off. The results show that under synthetic jet switched on, the dissipated heat is 3.7 times higher than when synthetic jet is switched off.

Sign in / Sign up

Export Citation Format

Share Document