Numerical study of the effect of graphene nanoparticles in calcium chloride hexahydrate -based phase change material on melting and freezing time in a circular cavity with a triangular obstacle

2021 ◽  
Vol 43 ◽  
pp. 103243
Author(s):  
Yacine Khetib ◽  
Ahmad Aziz Alahmadi ◽  
Ali Alzaed ◽  
S. Mohammad Sajadi ◽  
Goshtasp Cheraghian ◽  
...  
Keyword(s):  
Phase Change ◽  
Phase Change Material ◽  
Calcium Chloride ◽  
Numerical Study ◽  
Circular Cavity ◽  
Freezing Time ◽  
Chloride Hexahydrate ◽  
Graphene Nanoparticles ◽  
Change Material

NUMERICAL STUDY OF A SOLAR GREENHOUSE DRYER WITH A PHASE-CHANGE MATERIAL AS AN ENERGY STORAGE MEDIUM

2018 ◽  
Vol 49 (6) ◽  
pp. 509-528 ◽  
Author(s):  
Orawan Aumporn ◽  
Belkacem Zeghmati ◽  
Xavier Chesneau ◽  
Serm Janjai
Keyword(s):  
Energy Storage ◽  
Phase Change ◽  
Phase Change Material ◽  
Numerical Study ◽  
Storage Medium ◽  
Solar Greenhouse ◽  
Change Material

Numerical Performances Study of Curved Photovoltaic Panel Integrated with Phase Change Material

2020 ◽  
Vol 22 (4) ◽  
pp. 1439-1452
Author(s):  
Mohamed L. Benlekkam ◽  
Driss Nehari ◽  
Habib Y. Madani
Keyword(s):  
Phase Change ◽  
Phase Change Material ◽  
Numerical Study ◽  
Numerical Data ◽  
Navier Stokes ◽  
Photovoltaic Panel ◽  
Pv Panel ◽  
Energy Equations ◽  
Solid Liquid ◽  
Change Material

AbstractThe temperature rise of photovoltaic’s cells deteriorates its conversion efficiency. The use of a phase change material (PCM) layer linked to a curved photovoltaic PV panel so-called PV-mirror to control its temperature elevation has been numerically studied. This numerical study was carried out to explore the effect of inner fins length on the thermal and electrical improvement of curved PV panel. So a numerical model of heat transfer with solid-liquid phase change has been developed to solve the Navier–Stokes and energy equations. The predicted results are validated with an available experimental and numerical data. Results shows that the use of fins improve the thermal load distribution presented on the upper front of PV/PCM system and maintained it under 42°C compared with another without fins and enhance the PV cells efficiency by more than 2%.

scholarly journals Numerical Simulation of the Impact of the Heat Source Position on Melting of a Nano-Enhanced Phase Change Material

Nanomaterials ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 1425
Author(s):  
Tarek Bouzennada ◽  
Farid Mechighel ◽  
Kaouther Ghachem ◽  
Lioua Kolsi
Keyword(s):  
Heat Transfer ◽  
Phase Change ◽  
Phase Change Material ◽  
Numerical Study ◽  
Melting Rate ◽  
Heat Transfer Fluid ◽  
Commercial Code ◽  
Tube Position ◽  
The Impact ◽  
Change Material

A 2D-symmetric numerical study of a new design of Nano-Enhanced Phase change material (NEPCM)-filled enclosure is presented in this paper. The enclosure is equipped with an inner tube allowing the circulation of the heat transfer fluid (HTF); n-Octadecane is chosen as phase change material (PCM). Comsol-Multiphysics commercial code was used to solve the governing equations. This study has been performed to examine the heat distribution and melting rate under the influence of the inner-tube position and the concentration of the nanoparticles dispersed in the PCM. The inner tube was located at three different vertical positions and the nanoparticle concentration was varied from 0 to 0.06. The results revealed that both heat transfer/melting rates are improved when the inner tube is located at the bottom region of the enclosure and by increasing the concentration of the nanoparticles. The addition of the nanoparticles enhances the heat transfer due to the considerable increase in conductivity. On the other hand, by placing the tube in the bottom area of the enclosure, the liquid PCM gets a wider space, allowing the intensification of the natural convection.

Sign in / Sign up

Export Citation Format

Share Document