Novel soot loading prediction model of diesel particulate filter based on collection mechanism and equivalent permeability

Fuel ◽  
2021 ◽  
Vol 286 ◽  
pp. 119409
Author(s):  
De-yuan Wang ◽  
Pi-qiang Tan ◽  
Lei Zhu ◽  
Yin-huan Wang ◽  
Zhi-yuan Hu ◽  
...  
2019 ◽  
pp. 146808741987457 ◽  
Author(s):  
Jun Zhang ◽  
Yanfei Li ◽  
Victor W Wong ◽  
Shijin Shuai ◽  
Jinzhu Qi ◽  
...  

Diesel particulate filters are indispensable for diesel engines to meet the increasingly stringent emission regulations. A large amount of ash would accumulate in the diesel particulate filter over time, which would significantly affect the diesel particulate filter performance. In this work, the lubricant-derived ash effects on diesel particulate filter pressure drop, diesel particulate filter filtration performance, diesel particulate filter temperature field during active regeneration, and diesel particulate filter downstream emissions during active regeneration were studied on an engine test bench. The test results show that the ash accumulated in the diesel particulate filter would decrease the diesel particulate filter pressure drop due to the “membrane effect” when the diesel particulate filter ash loading is lower than about 10 g/L, beyond which the diesel particulate filter pressure drop would be increased due to the reduction of diesel particulate filter effective volume. The ash loaded in the diesel particulate filter could significantly improve the diesel particulate filter filtration efficiency because it would fill the pores of diesel particulate filter wall. The diesel particulate filter peak temperature during active regeneration is consistent with the diesel particulate filter initial actual soot loading density prior to regeneration at various diesel particulate filter ash loading levels, while the diesel particulate filter maximum temperature gradient would increase with the diesel particulate filter ash loading increase, whether the diesel particulate filter is regenerated at the same soot loading level or the same diesel particulate filter pressure drop level. The ash accumulation in the diesel particulate filter shows little effects on diesel particulate filter downstream CO, total hydrocarbons, N2O emissions, and NO2/NO x ratio during active regeneration. However, a small amount of SO2 emissions was observed when the diesel particulate filter ash loading is higher than 10 g/L. The ash accumulated in the diesel particulate filter would increase the diesel particulate filter downstream sub-23 nm particle emissions but decrease larger particle emissions during active regeneration.


2004 ◽  
Vol 5 (2) ◽  
pp. 163-173 ◽  
Author(s):  
O. A. Haralampous ◽  
I. P. Kandylas ◽  
G. C. Koltsakis ◽  
Z. C. Samaras

2013 ◽  
Vol 864-867 ◽  
pp. 1386-1393 ◽  
Author(s):  
Di Ming Lou ◽  
Ze Wei Zhu ◽  
Pi Qiang Tan ◽  
Zhi Yuan Hu

On-road particle emissions were tested in urban areas of Shanghai from a diesel bus equipping diesel particulate filter with fuel burner. EEPS 3090 particle analyzer was used for analyzing concentrations of particles in different diameters. In this paper, characterization of particles in soot loading and regeneration processes were identified, and particle reduction ability of DPF bus was analyzed. Result shows that, the averaged particle emission rate from DPF bus was degraded by 1 to 2 orders of magnitude during soot loading. Particle concentration distribution was transformed from nuclei-accumulated bi-modal pattern to uniformly multi-peaks patterns. In DPF regeneration process, particles of accumulated mode sized between 60.4nm and 107.5nm were decomposed and oxidized into fine nuclei particles of 29.4nm to 60.4nm, which increases total particle concentration. Reduction percentage of particle number per kilometer of DPF bus for soot loading and regeneration process reaches respectively 97% and 83.2% compared with normal diesel bus.


Sign in / Sign up

Export Citation Format

Share Document