An investigation on the solvent based carbon capture and storage system by process modeling and comparisons with another carbon control methods for different ships

2021 ◽  
Vol 110 ◽  
pp. 103438
Author(s):  
Engin Güler ◽  
Selma Ergin
Keyword(s):  
Process Modeling ◽  
Carbon Capture ◽  
Storage System ◽  
Carbon Capture And Storage ◽  
Control Methods ◽  
And Storage ◽  
Carbon Control

scholarly journals Optimization of Network Carbon Capture and Storage System (CCS) Using Mathematical Approach

2015 ◽  
Vol 9 (7) ◽  
pp. 161
Author(s):  
David Licindo ◽  
Arinne Christin Paramudita ◽  
Renanto Handogo ◽  
Juwari Purwo Sutikno
Keyword(s):  
Carbon Capture ◽  
Storage System ◽  
Carbon Capture And Storage ◽  
Exact Result ◽  
Maximum Load ◽  
Mathematical Approach ◽  
Source To Sink ◽  
Storage Location ◽  
The Cost ◽  
And Storage

Carbon capture and storage (CCS) is one of the technologies to reduce greenhouse gas emissions (GHG) tocapture of CO2 from the flue gas of a power plant that typically use coal as a Source of energy and then store it ina suitable geological storage (in specific locations). In practice, these sites may not be readily available forstorage at the same time that the Sources (GHG producing) are operating which gives rise to multi – periodplanning problems. This study presents a mathematical approach by considering constraints limit flowratereceived by Sink, various time availability of Sink and Source and calculation with the purpose to determine theminimum cost network which is getting the maximum load that is exchanged from Source to Sink. Illustrativecase studies are given to demonstrate the application of mathematical models to obtained with the exact result ofthe exchange network from Source to Sink. Derived from network obtained from the calculation of theMaximum Load Source to Sink and results may vary in accordance with the limitations that exist in themathematical model. The case study has been prepared with 2 cases, first 6 Source and 3 Sink with value ofSource Load is greater than the amount available on the Sink. Also, second case is 2 Source and 5 Sinkwithvalue of Source Load is smaller than the amount available on the Sink. In addition, Case Studies tominimize the cost of pipeline construction and distribution of CO2 by plant and storage location determination inJava. Flowrate restriction factor that goes into Sink, Source and Sink establishment time and cost are taken intoaccount can affect the networks that can be exchanged from the Source to the Sink.

Novel methodology for EEDI calculation considering onboard carbon capture and storage system

2021 ◽  
Vol 105 ◽  
pp. 103241
Author(s):  
Sanghyuk Lee ◽  
Seunghyeon Yoo ◽  
Hyunjun Park ◽  
Junkeon Ahn ◽  
Daejun Chang
Keyword(s):  
Carbon Capture ◽  
Storage System ◽  
Carbon Capture And Storage ◽  
And Storage

scholarly journals Assessing Potential Thermo-Mechanical Impacts on Caprock Due to CO2 Injection—A Case Study from Northern Lights CCS

Energies ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 5054
Author(s):  
Nicholas Thompson ◽  
Jamie Stuart Andrews ◽  
Tore Ingvald Bjørnarå
Keyword(s):  
Effective Stress ◽  
Carbon Capture ◽  
Storage System ◽  
Carbon Capture And Storage ◽  
Development Planning ◽  
Co2 Injection ◽  
Field Development ◽  
Stress Changes ◽  
Pressure Changes ◽  
And Storage

Due to significant temperature differences between the injected medium and in situ formation, injection of CO2 (as with water or other cold fluids) at depth induces thermal changes that must be accounted for a complete understanding of the mechanical integrity of the injection/storage system. Based on evaluations for the Northern Lights Carbon Capture and Storage (CCS) project, we focus on thermal effects induced on the caprock via conduction from cooling in the storage sands below. We investigate, using both analytical and numerical approaches, how undrained effects within the low permeability caprock can lead to volumetric contraction differences between the rock framework and the pore fluid which induce both stress and pore pressure changes that must be properly quantified. We show that such undrained effects, while inducing a more complicated response in the stress changes in the caprock, do not necessarily lead to unfavourable tensile conditions, and may, in fact, lead to increases in effective stress. These observations build confidence in the integrity of the caprock/seal system. We also show, through conservative assumptions, that pressure communication between the caprock and storage sands may lead to a localised negative effective stress condition, challenging stability of the base caprock, which will be mitigated for in field development planning.

scholarly journals Carbon Capture and Storage System Using Pinch Design Method

2018 ◽  
Vol 156 ◽  
pp. 03005
Author(s):  
Renanto Handogo
Keyword(s):  
Carbon Capture ◽  
Design Method ◽  
Storage System ◽  
Carbon Capture And Storage ◽  
Water System ◽  
Time Frame ◽  
Time Difference ◽  
Sources And Sinks ◽  
Reduce Carbon Dioxide ◽  
And Storage

Carbon capture and storage (CCS) have been investigated for a long time. It was intended to reduce carbon dioxide (CO2) in the atmosphere due to fossil fuel combustion in power generation and industrial processes. CO2 is captured and stored in various geological formations. The problem here is to match between source and sink such that alternative storage and unutilized storage capacities are minimum. Pinch Design Method as has been proposed by was used in this work. The concept is overwhelming that it can be used other than in the heat exchanger networks, such as in the water system design, mass exchanger networks and many other processes. Initially this concept was applied to carbon capture and storage but with no exact pairing between sources and sinks as proposed in this work using grid diagram as commonly shown in other processes. This work can point out the exact pairing between sources and sinks, and within the given time frame. A four different cases are investigated where the time difference between the starting time of CO2 generated in the source and the beginning of sink availability. A value of 0, 5, 10 and 15 years are chosen to evaluate the amount of CO2 that has to be stored and the amount of unutilized storage capacity. The case study has been prepared with 5 sources and 3 sinks. The result shows that the larger time difference the larger alternative storage and unutilized storage capacities. Therefore, having a shorter time difference will be more acceptable in the design CCS system.

Sign in / Sign up

Export Citation Format

Share Document