Correlations of heat transfer effectiveness in a minichannel heat sink with water-based suspensions of Al2O3 nanoparticles and/or MEPCM particles

2014 ◽  
Vol 69 ◽  
pp. 293-299 ◽  
Author(s):  
C.J. Ho ◽  
Wei-Chen Chen ◽  
Wei-Mon Yan
Keyword(s):  
Heat Transfer ◽  
Heat Sink ◽  
Al2o3 Nanoparticles ◽  
Water Based

An experimental investigation of heat transfer characteristics of water based Al2O3 nanofluid operated shell and tube heat exchanger with air bubble injection technique

2017 ◽  
Vol 6 (4) ◽  
pp. 83 ◽  
Author(s):  
Gaurav Thakur ◽  
Gurpreet Singh
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Al2o3 Nanoparticles ◽  
Air Bubbles ◽  
Heat Transfer Characteristics ◽  
Tube Heat Exchanger ◽  
Air Bubble ◽  
Transfer Characteristics ◽  
Water Based ◽  
Shell And Tube

The thermal performance of shell and tube heat exchangers has been enhanced with the use of different techniques. Air bubble injection is one such promising and inexpensive technique that enhances the heat transfer characteristics inside shell and tube heat exchanger by creating turbulence in the flowing fluid. In this paper, experimental study on heat transfer characteristics of shell and tube heat exchanger was done with the injection of air bubbles at the tube inlet and throughout the tube with water based Al2O3 nanofluids i.e. (0.1%v/v and 0.2%v/v). The outcomes obtained for both the concentrations at two distinct injection points were compared with the case when air bubbles were not injected. The outcomes revealed that the heat transfer characteristics enhanced with nanoparticles volumetric concentration and the air bubble injection. The case where air bubbles were injected throughout the tube gave maximum enhancement followed by the cases of injection of air bubbles at the tube inlet and no air bubble injection. Besides this, water based Al2O3 nanofluid with 0.2%v/v of Al2O3 nanoparticles gave more enhancement than Al2O3nanofluid with 0.1%v/v of Al2O3 nanoparticles as the enhancement in the heat transfer characteristics is directly proportional to the volumetric concentration of nanoparticles in the base fluid. The heat transfer rate showed an enhancement of about 25-40% and dimensionless exergy loss showed an enhancement of about 33-43% when air bubbles were injected throughout the tube. Moreover, increment in the heat transfer characteristics was also found due to increase in the temperature of the hot fluid keeping the flow rate of both the heat transfer fluids constant.

Numerical Study of Forced Convection of Nanofluids in a Microchannel Heat Sink

2008 ◽  
Author(s):  
Parisa Vaziee ◽  
Omid Abouali
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Heat Sink ◽  
Volume Fraction ◽  
Numerical Study ◽  
Heat Removal ◽  
Al2o3 Nanoparticles ◽  
Microchannel Heat Sink ◽  
Particle Volume ◽  
Volume Fractions

Effectiveness of the microchannel heat sink cooled by nanofluids with various particle volume fractions is investigated numerically using the latest theoretical models for conductivity and viscosity of the nanofluids. Both laminar and turbulent flows are considered in this research. The model of conductivity used in this research accounts for the fundamental role of Brownian motion of the nanoparticles which is in good agreement with the experimental data. The changes in viscosity of the nanofluid due to temperature variation are considered also. Final results are compared with the experimental measurements for heat transfer coefficient and pressure drop in microchannel. Enhancement in heat transfer is achieved for laminar flow with increasing of volume fraction of Al2O3 nanoparticles. But for turbulent flow an enhancement of heat removal was not seen and using higher volume fractions of nanoparticles increases the maximum substrate temperature. Pressure drop is increased with using nanofluids because of the augmentation in the viscosity and this increase is more noticeable in higher Reynolds numbers.

Effects of Al2O3-Water Nanofluid and Angular Orientation on Entropy Generation and Convective Heat Transfer of an Elliptical Micro-Pin-Fin Heat Sink

2014 ◽  
Author(s):  
Husam Rajab ◽  
Da Yin ◽  
Hongbin Ma
Keyword(s):  
Heat Transfer ◽  
Entropy Generation ◽  
Heat Sink ◽  
Heat Transfer Performance ◽  
Volume Fraction ◽  
Al2o3 Nanoparticles ◽  
Transfer Performance ◽  
Enhancement Of Heat Transfer ◽  
Pin Fin ◽  
Prandtl Numbers

This paper presents an investigation of the effect of nanofluid on the heat transfer performance in an elliptical micro-pin-fin heat sink including the influence of entropy generation and pin orientation. The orientation angle of pins is decreased with the number of pins in the array with a 90 degree angle for the first pin and a 0 degree angle for the last pin. To study the flow and heat transfer behaviors in a micro-pin-fin heat sink, steady Navier-Stokes and energy equations were discretized using a finite volume approach and were solved iteratively. Deionized (DI) water was used as a base coolant fluid while aluminum oxide (Al2O3) nanoparticles were used in the present study with mean diameters of 41.6 nm. The results showed that (1) changing the angular orientation of pins can cause significant enhancement in heat transfer, (2) a significant enhancement of heat transfer can be attained in the system due to the suspension of Al2O3 nanoparticles in the base fluid in comparison with pure water, (3) enhancement of heat transfer is intensified with increasing volume fraction of nanoparticles and Reynolds and Prandtl numbers, (4) increasing volume fraction of nanoparticles, which is responsible for higher heat transfer performance, leads to a higher pressure drop, (5) using nanofluids as coolant can cause lower heat transfer entropy generation due to their high thermal properties, and (6) with increasing volume fraction and Reynolds and Prandtl numbers, overall entropy generation rate decreases.

Sign in / Sign up

Export Citation Format

Share Document