Protrusions formed during primary recrystallization of cross-rolled coarse-grained niobium

2019 ◽  
Vol 85 ◽  
pp. 105080
Author(s):  
T. Brekailo ◽  
D.R. Almeida ◽  
M. Avalos ◽  
R.E. Bolmaro ◽  
H.R.Z. Sandim
Keyword(s):  
Primary Recrystallization ◽  
Coarse Grained

An EBSD Study on Orientation Effects during Recrystallization of Coarse-Grained Niobium

2004 ◽  
Vol 467-470 ◽  
pp. 519-524 ◽  
Author(s):  
Hugo Ricardo Zschommler Sandim ◽  
Dierk Raabe
Keyword(s):  
Longitudinal Section ◽  
Primary Recrystallization ◽  
Coarse Grained ◽  
Subgrain Structure ◽  
Electron Backscattered Diffraction ◽  
Subgrain Growth ◽  
Metallographic Inspection ◽  
Cold Rolled ◽  
Cold Worked ◽  
Viable Mechanism

The recrystallization behavior of coarse-grained niobium depends on the nature of its deformation microstructure. In this regard, a longitudinal section of a high-purity coarse-grained niobium ingot was cold rolled to a thickness reduction of 96% followed by annealing in vacuum at 800°C for 1 h. Metallographic inspection in cold-rolled and annealed specimens was carried out in a field emission gun scanning electron microscope (FEG-SEM). Microtexture was determined by electron-backscattered diffraction (EBSD) coupled to the FEG-SEM. The use this technique has evidenced details of the boundary character and subgrain structure found in partially recrystallized regions. The early stages of primary recrystallization are associated to the presence of high-angle lamellar boundaries found in the cold-worked state. Abnormal subgrain growth has been evidenced as a viable mechanism for nucleation of recrystallization.

The Alteration of the Pore Spaces in Sandstones

1973 ◽  
Vol 31 ◽  
pp. 210-211
Author(s):  
R. E. Ferrell ◽  
G. G. Paulson
Keyword(s):  
Electron Microscope ◽  
Scanning Electron Microscope ◽  
The Other ◽  
Coarse Grained ◽  
Depositional Fabric ◽  
Soluble Components ◽  
Scanning Electron ◽  
Shape And Size

The pore spaces in sandstones are the result of the original depositional fabric and the degree of post-depositional alteration that the rock has experienced. The largest pore volumes are present in coarse-grained, well-sorted materials with high sphericity. The chief mechanisms which alter the shape and size of the pores are precipitation of cementing agents and the dissolution of soluble components. Each process may operate alone or in combination with the other, or there may be several generations of cementation and solution.The scanning electron microscope has ‘been used in this study to reveal the morphology of the pore spaces in a variety of moderate porosity, orthoquartzites.

On the Origin of the Microscystalline Structure in Rapidly Solidified IN-100 Powder

1977 ◽  
Vol 35 ◽  
pp. 260-261
Author(s):  
J. M. Walsh ◽  
K. P. Gumz ◽  
J. C. Whittles ◽  
B. H. Kear
Keyword(s):  
The Other ◽  
Coarse Grained ◽  
Microcrystalline Structure ◽  
Routine Examination ◽  
Atomization Process ◽  
Centrifugal Atomization ◽  
Splat Quenching ◽  
Powder Particles ◽  
Dendritic Microstructures ◽  
Rapidly Solidified

During a routine examination of the microstructure of rapidly solidified IN-100 powder, produced by a newly-developed centrifugal atomization process1, essentially two distinct types of microstructure were identified. When a high melt superheat is maintained during atomization, the powder particles are predominantly coarse-grained, equiaxed or columnar, with distinctly dendritic microstructures, Figs, la and 4a. On the other hand, when the melt superheat is reduced by increasing the heat flow to the disc of the rotary atomizer, the powder particles are predominantly microcrystalline in character, with typically one dendrite per grain, Figs, lb and 4b. In what follows, evidence is presented that strongly supports the view that the unusual microcrystalline structure has its origin in dendrite erosion occurring in a 'mushy zone' of dynamic solidification on the disc of the rotary atomizer.The critical observations were made on atomized material that had undergone 'splat-quenching' on previously solidified, chilled substrate particles.

In situ investigation of the primary recrystallization of alpha titanium in HVEM

1978 ◽  
Vol 36 (1) ◽  
pp. 634-635
Author(s):  
S. Naka ◽  
R. Penelle ◽  
R. Valle
Keyword(s):  
Dimensional Analysis ◽  
Texture Evolution ◽  
Cold Work ◽  
Three Dimensional ◽  
Primary Recrystallization ◽  
Thin Foils ◽  
In Situ Investigation ◽  
Grain Growth Model ◽  
Alpha Titanium

The in situ experimentation technique in HVEM seems to be particularly suitable to clarify the processes involved in recrystallization. The material under investigation was unidirectionally cold-rolled titanium of commercial purity. The problem was approached in two different ways. The three-dimensional analysis of textures was used to describe the texture evolution during the primary recrystallization. Observations of bulk-annealed specimens or thin foils annealed in the microscope were also made in order to provide information concerning the mechanisms involved in the formation of new grains. In contrast to the already published work on titanium, this investigation takes into consideration different values of the cold-work ratio, the temperature and the annealing time.Two different models are commonly used to explain the recrystallization textures i.e. the selective grain growth model (Beck) or the oriented nucleation model (Burgers). The three-dimensional analysis of both the rolling and recrystallization textures was performed to identify the mechanismsl involved in the recrystallization of titanium.

Correlation between dislocation, grain boundary and interface of duplex SS in stress corrosion cracking(SCC)

1990 ◽  
Vol 48 (4) ◽  
pp. 928-929
Author(s):  
Wang Zheng-fang ◽  
Z.F. Wang
Keyword(s):  
Stainless Steel ◽  
Thermal Cycle ◽  
Secondary Phase ◽  
Corrosion Cracking ◽  
Coarse Grained ◽  
Test Environment ◽  
Fine Grained ◽  
Evaluation Test ◽  
Welding Thermal Cycle ◽  
Micro Analysis

The main purpose of this study highlights on the evaluation of chloride SCC resistance of the material,duplex stainless steel,OOCr18Ni5Mo3Si2 (18-5Mo) and its welded coarse grained zone(CGZ).18-5Mo is a dual phases (A+F) stainless steel with yield strength:512N/mm2 .The proportion of secondary Phase(A phase) accounts for 30-35% of the total with fine grained and homogeneously distributed A and F phases(Fig.1).After being welded by a specific welding thermal cycle to the material,i.e. Tmax=1350°C and t8/5=20s,microstructure may change from fine grained morphology to coarse grained morphology and from homogeneously distributed of A phase to a concentration of A phase(Fig.2).Meanwhile,the proportion of A phase reduced from 35% to 5-10°o.For this reason it is known as welded coarse grained zone(CGZ).In association with difference of microstructure between base metal and welded CGZ,so chloride SCC resistance also differ from each other.Test procedures:Constant load tensile test(CLTT) were performed for recording Esce-t curve by which corrosion cracking growth can be described, tf,fractured time,can also be recorded by the test which is taken as a electrochemical behavior and mechanical property for SCC resistance evaluation. Test environment:143°C boiling 42%MgCl2 solution is used.Besides, micro analysis were conducted with light microscopy(LM),SEM,TEM,and Auger energy spectrum(AES) so as to reveal the correlation between the data generated by the CLTT results and micro analysis.

Input of coarse-grained siliciclastics into the Pyrenean Basin during the PETM (1): overview

2014 ◽  
Vol 31 ◽  
pp. 177-178
Author(s):  
Victoriano Pujalte ◽  
Juan Ignacio Baceta ◽  
Birger Schmitz
Keyword(s):  
Coarse Grained

Patterns in diversity and composition of the microbenthos of subarctic intertidal beaches with different morphodynamics

2020 ◽  
Vol 648 ◽  
pp. 19-38
Author(s):  
AI Azovsky ◽  
YA Mazei ◽  
MA Saburova ◽  
PV Sapozhnikov
Keyword(s):  
Species Abundance ◽  
Abundance Ratio ◽  
Wave Action ◽  
Coarse Grained ◽  
Sediment Properties ◽  
Β Diversity ◽  
Α Diversity ◽  
Wide Range ◽  
Similar Mode ◽  
Abundance And Diversity

Diversity and composition of benthic diatom algae and ciliates were studied at several beaches along the White and Barents seas: from highly exposed, reflective beaches with coarse-grained sands to sheltered, dissipative silty-sandy flats. For diatoms, the epipelic to epipsammic species abundance ratio was significantly correlated with the beach index and mean particle size, while neither α-diversity measures nor mean cell length were related to beach properties. In contrast, most of the characteristics of ciliate assemblages (diversity, total abundance and biomass, mean individual weight and percentage of karyorelictids) demonstrated a strong correlation to beach properties, remaining low at exposed beaches but increasing sharply in more sheltered conditions. β-diversity did not correlate with beach properties for either diatoms or ciliates. We suggest that wave action and sediment properties are the main drivers controlling the diversity and composition of the intertidal microbenthos. Diatoms and ciliates, however, demonstrated divergent response to these factors. Epipelic and epipsammic diatoms exhibited 2 different strategies to adapt to their environments and therefore were complementarily distributed along the environmental gradient and compensated for each other in diversity. Most ciliates demonstrated a similar mode of habitat selection but differed in their degree of tolerance. Euryporal (including mesoporal) species were relatively tolerant to wave action and therefore occurred under a wide range of beach conditions, though their abundance and diversity were highest in fine, relatively stable sediments on sheltered beaches, whereas the specific interstitial (i.e. genuine microporal) species were mostly restricted to only these habitats.

Sign in / Sign up

Export Citation Format

Share Document