Correlation between dislocation, grain boundary and interface of duplex SS in stress corrosion cracking(SCC)

1990 ◽  
Vol 48 (4) ◽  
pp. 928-929
Author(s):  
Wang Zheng-fang ◽  
Z.F. Wang
Keyword(s):  
Stainless Steel ◽  
Thermal Cycle ◽  
Secondary Phase ◽  
Corrosion Cracking ◽  
Coarse Grained ◽  
Test Environment ◽  
Fine Grained ◽  
Evaluation Test ◽  
Welding Thermal Cycle ◽  
Micro Analysis

The main purpose of this study highlights on the evaluation of chloride SCC resistance of the material,duplex stainless steel,OOCr18Ni5Mo3Si2 (18-5Mo) and its welded coarse grained zone(CGZ).18-5Mo is a dual phases (A+F) stainless steel with yield strength:512N/mm2 .The proportion of secondary Phase(A phase) accounts for 30-35% of the total with fine grained and homogeneously distributed A and F phases(Fig.1).After being welded by a specific welding thermal cycle to the material,i.e. Tmax=1350°C and t8/5=20s,microstructure may change from fine grained morphology to coarse grained morphology and from homogeneously distributed of A phase to a concentration of A phase(Fig.2).Meanwhile,the proportion of A phase reduced from 35% to 5-10°o.For this reason it is known as welded coarse grained zone(CGZ).In association with difference of microstructure between base metal and welded CGZ,so chloride SCC resistance also differ from each other.Test procedures:Constant load tensile test(CLTT) were performed for recording Esce-t curve by which corrosion cracking growth can be described, tf,fractured time,can also be recorded by the test which is taken as a electrochemical behavior and mechanical property for SCC resistance evaluation. Test environment:143°C boiling 42%MgCl2 solution is used.Besides, micro analysis were conducted with light microscopy(LM),SEM,TEM,and Auger energy spectrum(AES) so as to reveal the correlation between the data generated by the CLTT results and micro analysis.

Microstructural evolution and mechanical integrity relationship of dissimilar metal welding between 2205 duplex stainless steel and composite bimetallic plates

2021 ◽  
pp. 095440622110036
Author(s):  
Changqing Ye ◽  
Weiguo Zhai ◽  
Guangyao Lu ◽  
Qingsong Liu ◽  
Liang Ni ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Weld Metal ◽  
Duplex Stainless Steel ◽  
Intergranular Corrosion ◽  
Thermal Cycle ◽  
Filler Metal ◽  
2205 Duplex Stainless Steel ◽  
Welding Thermal Cycle ◽  
Intergranular Corrosion Resistance

In this paper, shielded metal arc welding on the dissimilar joint between 2205 duplex stainless steel and composite bimetallic plates (304 L stainless steel/10CrNi3MoV steel) with a filler metal E2209 was performed. Furthermore, the microstructure, phase, mechanical properties and intergranular corrosion resistance of the joints were investigated and element distributions of the interfaces were characterized. The results show that austenite transformed to ferrite under the influence of welding thermal cycle, and then a large amount of ferrite appeared in heat affected zone (HAZ) of 2205 duplex stainless steel. Coarse bainite grains were formed in HAZ of the 10CrNi3MoV steel near the fusion line with high temperature welding thermal cycle. Fine granular bainite was also generated in HAZ of 10CrNi3MoV steel due to the relatively short exposure time to the active temperature of grain growth. Local peak temperature near the base 10CrNi3MoV steel was still high enough to recrystallize the 10CrNi3MoV steel to form partial-recrystallization HAZ due to phase change. The filler metal was compatible with the three kinds of base materials. The thickness of the elemental diffusion interfaces layers was about 100 µm. The maximum microhardness value was obtained in the HAZ of 2205 duplex stainless steel (287 ± 14 HV), and the minimum one appeared in HAZ of SS304L (213 ± 5 HV). The maximum tensile strength of the welded joint was about 670 ± 6 MPa, and the tensile specimens fractured in ductile at matrix of the composite bimetallic plates. The impact energy of the weld metal and HAZ of the 10CrNi3MoV steel tested at –20 °C were 274 ± 6 J and 308 ± 5 J, respectively. Moreover, the intergranular corrosion resistance of the weldment including 304 L stainless steel, weld metal, HAZs and 2205 duplex stainless steel was in good agreement with the functional design requirements of materials corrosion resistance.

Microstructural Refinement in a Commercial Aluminum Alloy Processed by ECAP Using a Die Channel Angle of 110 Degrees

2015 ◽  
Vol 1114 ◽  
pp. 3-8
Author(s):  
Nicolae Şerban ◽  
Doina Răducanu ◽  
Nicolae Ghiban ◽  
Vasile Dănuţ Cojocaru
Keyword(s):  
Grain Refinement ◽  
Cross Section ◽  
High Strength ◽  
Secondary Phase ◽  
Coarse Grained ◽  
Metallographic Analysis ◽  
Second Phase ◽  
Channel Angle ◽  
Ambient Temperatures ◽  
Fine Grained

The properties of ultra-fine grained materials are superior to those of corresponding conventional coarse grained materials, being significantly improved as a result of grain refinement. Equal channel angular pressing (ECAP) is an efficient method for modifying the microstructure by refining grain size via severe plastic deformation (SPD) in producing ultra-fine grained materials (UFG) and nanomaterials (NM). The grain sizes produced by ECAP processing are typically in the submicrometer range and this leads to high strength at ambient temperatures. ECAP is performed by pressing test samples through a die containing two channels, equal in cross-section and intersecting at a certain angle. The billet experiences simple shear deformation at the intersection, without any precipitous change in the cross-section area because the die prevents lateral expansion and therefore the billet can be pressed more than once and it can be rotated around its pressing axis during subsequent passes. After ECAP significant grain refinement occurs together with dislocation strengthening, resulting in a considerable enhancement in the strength of the alloys. A commercial AlMgSi alloy (AA6063) was investigated in this study. The specimens were processed for a number of passes up to nine, using a die channel angle of 110°, applying the ECAP route BC. After ECAP, samples were cut from each specimen and prepared for metallographic analysis. The microstructure of the ECAP-ed and as-received material was investigated using optical (OLYMPUS – BX60M) and SEM microscopy (TESCAN VEGA II – XMU). It was determined that for the as-received material the microstructure shows a rough appearance, with large grains of dendritic or seaweed aspect and with a secondary phase at grain boundaries (continuous casting structure). For the ECAP processed samples, the microstructure shows a finished aspect, with refined, elongated grains, also with crumbled and uniformly distributed second phase particles after a typical ECAP texture.

Effect of Ultrasonic Impact Treatment on the Stress Corrosion Cracking of 304 Stainless Steel Welded Joints

2008 ◽  
Author(s):  
Gang Ma ◽  
Xiang Ling
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Stainless Steel ◽  
Stress Corrosion ◽  
Stress Corrosion Cracking ◽  
Welded Joints ◽  
Corrosion Cracking ◽  
Coarse Grained ◽  
304 Stainless Steel ◽  
Ultrasonic Impact Treatment

High tensile weld residual stress is an important factor contributing to stress corrosion cracking (SCC). Ultrasonic impact treatment (UIT) can produce compressive stresses on the surface of welded joints that negate the tensile stresses to enhance the SCC resistance of welded joints. In the present work, X-ray diffraction method was used to obtain the distribution of residual stress induced by UIT. The results showed that UIT could cause a large compressive residual stress up to 325.9MPa on the surface of the material. A 3D finite element model was established to simulate the UIT process by using a finite element software ABAQUS. The residual stress distribution of the AISI 304 stainless steel induced by UIT was predicted by finite element analysis. In order to demonstrate the improvement of the SCC resistance of the welded joints, the specimens were immersed in boiling 42% magnesium chloride solution during SCC testing, and untreated specimen cracked after immersion for 23 hours. In contrast, treated specimens with different coverage were tested for 1000 hours without visible stress corrosion cracks. The microstructure observation results revealed that a hardened layer was formed on the surface and the initial coarse-grained structure in the surface was refined into ultrafine grains. The above results indicate that UIT is an effective approach for protecting weldments against SCC.

Effect of Ultrasonic Impact Treatment on the Stress Corrosion Cracking of 304 Stainless Steel Welded Joints

2009 ◽  
Vol 131 (5) ◽  
Author(s):  
Xiang Ling ◽  
Gang Ma
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Stainless Steel ◽  
Stress Corrosion ◽  
Stress Corrosion Cracking ◽  
Welded Joints ◽  
Corrosion Cracking ◽  
Coarse Grained ◽  
304 Stainless Steel ◽  
Ultrasonic Impact Treatment

High tensile weld residual stress is an important factor contributing to stress corrosion cracking (SCC). Ultrasonic impact treatment (UIT) can produce compressive stresses on the surface of welded joints that negate the tensile stresses to enhance the SCC resistance of welded joints. In the present work, X-ray diffraction method was used to obtain the distribution of residual stress induced by UIT. The results showed that UIT could cause a large compressive residual stress in access of 300 MPa on the surface of the material. A 3D finite element model was established to simulate the UIT process by using the finite element software ABAQUS. The residual stress distribution of the AISI 304 stainless steel induced by UIT was predicted by finite element analysis. In order to demonstrate the improvement of the SCC resistance of the welded joints, the specimens were immersed in boiling 42% magnesium chloride solution during SCC testing, and untreated specimen cracked after immersion for 23 h. In contrast, treated specimens with different impact duration were tested for 1000 h without visible stress corrosion cracks. The microstructure observation results revealed that a hardened layer was formed on the surface and the initial coarse-grained structure in the surface was refined into ultrafine grains. The above results indicate that UIT is an effective approach for protecting weldments against SCC.

Effect of alloy grain size on oxidation resistance of silica-coated stainless steel

1994 ◽  
Vol 52 ◽  
pp. 676-677
Author(s):  
C. S. McDowell ◽  
S. N. Basu
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Stainless Steel ◽  
Oxidation Resistance ◽  
Powder Processing ◽  
Hot Isostatic Pressing ◽  
Silica Coating ◽  
Austenitic Steels ◽  
Coarse Grained ◽  
Fine Grained

Oxidation resistance of stainless steels, which rely on the formation of a Cr2O3 (chromia) scale, can be further improved through minor alloying additions such as Al or Si, or by application of coatings to the exposed surfaces. Although, additions of Si to austenitic steels have demonstrated an improvement in oxidation resistance, high Si contents can be detrimental to the mechanical properties of these alloys. The application of a silica coating on the surface of the stainless steel provides improved oxidation resistance without detrimental effects on the mechanical properties. This study examines the effect of the grain size of the stainless steel on the effectiveness of a silica coating as an oxidation barrier.Fully austenitic stainless steel of composition Fe-18(wt%)Cr-20Ni-1.5Mn was produced in both coarsegrained and fine-grained form. The coarse-grained alloy, with a grain size of approximately 100 μm, was produced by casting and hot rolling. The fine-grained alloy, with a grain size of approximately 5 μm, was produced by rapid solidification powder processing, followed by consolidated by hot isostatic pressing and swaging.

The critical influence of La content on the microstructure-toughness relationship in the simulated coarse-grained heat-affected zone of high-strength low-alloy steels

2021 ◽  
Vol 118 (2) ◽  
pp. 212
Author(s):  
Yuxin Cao ◽  
Xiangliang Wan ◽  
Feng Zhou ◽  
Hangyu Dong ◽  
Kaiming Wu ◽  
...  
Keyword(s):  
Heat Affected Zone ◽  
Acicular Ferrite ◽  
High Strength ◽  
Coarse Grained ◽  
Low Alloy Steels ◽  
Fine Grained ◽  
Welding Thermal Cycle ◽  
Alloy Steels ◽  
High Fraction ◽  
The Impact

The present study was envisaged to investigate the role of La content on the particle, microstructure and toughness in the simulated coarse-grained heat-affected zone (CGHAZ) of high-strength low-alloy steels. Three steels with La content of 0.016 wt.%, 0.046 wt.% and 0.093 wt.% were prepared and simulated in a 100 kJ/cm heat input welding thermal cycle. Subsequently, the particle and microstructure of selected specimens were characterized and the impact absorb energy was measured at −20 °C. The results indicated that the La2O2S inclusions in 0.016 wt.%-La steel were gradually modified to LaS-LaP in 0.046 wt.%-La steel and to LaP in 0.093 wt.%-La steel. A higher fraction of acicular ferrite was obtained in the simulated CGHAZ of 0.016 wt.%-La steel, since the inclusion of La2O2S was more powerful to induce the formation of acicular ferrite. Furthermore, the fraction of M-A constituents in the simulated CGHAZ increased with increasing La content. The impact toughness in the simulated CGHAZ of 0.016 wt.%-La steel was the highest, owing to the high fraction of the fine-grained acicular ferrite and low fraction of M-A constituent.

The Impact of Grain Size on Oxidation Behavior of TP304H Austenitic Stainless Steel at High Temperature in Air

2011 ◽  
Vol 117-119 ◽  
pp. 990-994
Author(s):  
Wei Wei ◽  
Zhi Wu Wang ◽  
Mao Lin Liu
Keyword(s):  
Grain Size ◽  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Oxide Scale ◽  
Grain Refinement ◽  
Coarse Grained ◽  
X Ray ◽  
Fine Grained ◽  
Different Grain Size ◽  
The Impact

Exposed to 650°C air, TP304H stainless steel with two different grain size was oxidized at this temperature. At the meantime, comparison of their oxidation was through the oxidation kinetics curves and analysis of the morphology and composition of oxide scale which conducted by SEM and X-ray. The results showed that the oxidation rate of TP304H stainless steel was slowed down by grain refinement and oxide scale of fine-grained TP304H steel was thinner than that of coarse-grained steel. The nucleation and the growth of nuclei of coarse-grained oxide scale were more rapid. In addition, the grain refinement of austenitic stainless steel accelerated the diffusivity of Cr and made for the formation of dense and continuous oxide scale, so that the oxidation of stainless steel can be effectively inhabited.

Sign in / Sign up

Export Citation Format

Share Document