High saturation magnetic induction and low magnetostriction of a novel ferritic Fe-Ti alloy compared to a non-oriented silicon steel

2021 ◽  
Vol 527 ◽  
pp. 167702
Author(s):  
G.O. Fulop ◽  
M.B.S. Dias ◽  
H.R.Z. Sandim ◽  
C. Bormio-Nunes
Keyword(s):  
Magnetic Induction ◽  
Silicon Steel ◽  
Ti Alloy ◽  
High Saturation ◽  
Saturation Magnetic Induction

scholarly journals Impact of addition of ca on clogging of SEN and magnetic properties of non-oriented silicon steel

2019 ◽  
Vol 55 (1) ◽  
pp. 39-46
Author(s):  
W. Kong ◽  
D.G. Cang
Keyword(s):  
Magnetic Properties ◽  
Continuous Casting ◽  
Casting Speed ◽  
Magnetic Induction ◽  
Core Loss ◽  
Submerged Entry Nozzle ◽  
Silicon Steel ◽  
The Core ◽  
Dissolved Aluminum ◽  
The Impact

The submerged entry nozzle (SEN) clogging has been happening during continuous casting (or CC for short) for nonoriented silicon steel. To solve the problem, the paper studied a flow rate through SEN, a node attached to one of them, and the impact on the clogging. The results showed that when SEN is clogged seriously, the casting speed has to decrease below the target casting speed and that SEN clogging can be predicted by comparing the actual value and the theoretical one of a casting speed. Al2O3 and its composite inclusions caused the SEN clogging and the addition of Ca can solve SEN clogging during CC of the silicon steel both theoretically and practically. Furthermore, the impact of the addition of Ca on the magnetic properties of the steel were analyzed. The results showed that the core loss and the magnetic induction of the silicon steel decreased by using the addition of Ca, which generated more dissolved Aluminum, and the addition of Ca generated more harmful textures, which reduced the magnetic induction.

Effects of segregated sulfur on recrystallization texture and magnetic induction in thin-gauged 3% silicon steel

1999 ◽  
Vol 35 (5) ◽  
pp. 3373-3375 ◽  
Author(s):  
K.N. Chai ◽  
N.H. Heo ◽  
J.G. Na ◽  
H.-T. Jeong ◽  
S.R. Lee
Keyword(s):  
Magnetic Induction ◽  
Recrystallization Texture ◽  
Silicon Steel

Study of Microstructure and Magnetic Properties on High-Silicon Steel Composite Sheet

2013 ◽  
Vol 401-403 ◽  
pp. 828-831
Author(s):  
Xing Wen Yang ◽  
Jing Liu ◽  
Jing Tao Han ◽  
Shuai Ji
Keyword(s):  
Magnetic Properties ◽  
Magnetic Induction ◽  
Silicon Content ◽  
Silicon Steel ◽  
Iron Loss ◽  
Composite Sheet ◽  
High Silicon Steel ◽  
Composite Casting ◽  
Steel Composite ◽  
High Silicon

High-silicon composite casting blank with the silicon content of 12wt% in core layer and with the silicon content of 3wt% in coating layer was fabricated by composite casting. The high-silicon steel composite sheet with smooth surface and good shape can be obtained by hot rolling and warm rolling. After high temperature diffusion and pickling process, the composite sheet with thickness of 0.44mm and homogeneous silicon content of 5.8wt.% could be achieved finally. The test results of magnetic properties show that the magnetic induction intensity B50and iron loss P15/50are 1.778T and 2.892w/kg respectively. It implies that the high-silicon steel composite sheet with high magnetic induction and low iron loss can be prepared by composite casting and rolling process.

Solidification Structure and Segregation of High Magnetic Induction Grain-Oriented Silicon Steel

2019 ◽  
Vol 25 (6) ◽  
pp. 1586-1592
Author(s):  
Xin Li ◽  
Min Wang ◽  
YanPing Bao ◽  
Jian Gong ◽  
Xianhui Wang ◽  
...  
Keyword(s):  
Magnetic Induction ◽  
Silicon Steel ◽  
Solidification Structure ◽  
High Magnetic Induction

Study on Preparation of Ferrosilicon Alloy Deposition In Situ Melting Salt Production Power

2013 ◽  
Vol 712-715 ◽  
pp. 46-49 ◽  
Author(s):  
Jing Long Liang ◽  
Hui Li ◽  
Xiao Ya Geng
Keyword(s):  
Current Density ◽  
Magnetic Induction ◽  
Silicon Content ◽  
Molten Salts ◽  
Silicon Steel ◽  
Iron Loss ◽  
Technological Parameters ◽  
Limited Application ◽  
Deposit Layer

As a floppy alloy, the silicon steel with a content of Si of 6.5% has been paid much attention due to its maximum magnetic induction and minimum iron loss. However, the manufacture has been limited largely by conventional technics. By comparison, the silicon steel with a lower silicon content of 0.1%-4.0%, which was manufactured by conventional technics, also has a limited application. In this work, Molten Salts Electrodeposition has been employed to produce Fe-Si alloy. Technological parameters including influence of Molten Salts Electrodeposition technic in aggradation layer appearance and distribution of silicon content along with thickness. The results also show that the size of superficial particles on deposit layer increased gradually, the thickness of deposit layer was proportional to the current density on the deposit layer of Fe-Si.

The calculation of magnetic induction in grain orientated ultra-thin silicon steel sheets

2007 ◽  
Vol 42 (20) ◽  
pp. 8667-8670 ◽  
Author(s):  
Gao Xiuhua ◽  
Qi Kemin ◽  
Qiu Chunlin ◽  
Tian Yanwen
Keyword(s):  
Magnetic Induction ◽  
Silicon Steel ◽  
Steel Sheets ◽  
Thin Silicon

Precipitation Behavior of AlN in High-Magnetic-Induction Grain-Oriented Silicon Steel Slab

JOM ◽  
2019 ◽  
Vol 71 (9) ◽  
pp. 3135-3141 ◽  
Author(s):  
Xin Li ◽  
Min Wang ◽  
YanPing Bao ◽  
Jian Gong ◽  
Xianhui Wang ◽  
...  
Keyword(s):  
Magnetic Induction ◽  
Silicon Steel ◽  
Precipitation Behavior ◽  
Steel Slab ◽  
High Magnetic Induction
Sign in / Sign up

Export Citation Format

Share Document