Effect of cooling rate on microstructure evolution during α/β heat treatment of TA15 titanium alloy

2012 ◽  
Vol 70 ◽  
pp. 101-110 ◽  
Author(s):  
S. Zhu ◽  
H. Yang ◽  
L.G. Guo ◽  
X.G. Fan
Keyword(s):  
Heat Treatment ◽  
Titanium Alloy ◽  
Cooling Rate ◽  
Microstructure Evolution ◽  
Ta15 Titanium Alloy

Effect of Hot Processing on Mircrostructure and Properties of Flat Billets of TA15 Titanium Alloy

2021 ◽  
Vol 1016 ◽  
pp. 906-910
Author(s):  
Xin Hua Min ◽  
Cheng Jin
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Titanium Alloy ◽  
High Temperature ◽  
Room Temperature ◽  
High Strength ◽  
Slow Cooling ◽  
Microstructure And Mechanical Properties ◽  
Ta15 Titanium Alloy ◽  
The Ideal

In this paper,effect of the different forging processes on the microstructure and mechanical properties of the flat flat billets of TA15 titanium alloy was investigated.The flat billiets of 80 mm×150 mm×L sizes of TA15 titanium alloy are produced by four different forging processes.Then the different microstrure and properties of the flat billiets were obtained by heat treatment of 800 °C~850 °C×1 h~4h.The results show that, adopting the first forging temperature at T1 °C、slow cooling and the second forging temperature at T2°C 、quick cooling, the primary αphases content is just 10%, and there are lots of thin aciculate phases on the base. This microstructure has both high strength at room temperature and high temperature, while the properties between the cross and lengthwise directions are just the same. So the hot processing of the first forging temperature at T1 °C、slow cooling and the second forging temperature at T2°C 、quick cooling is choosed as the ideal processing for production of aircraft frame parts.

Effects of Heat Treatment on Microstructure of High-Strength Manganese-Silicon Steels

2017 ◽  
Vol 270 ◽  
pp. 239-245
Author(s):  
Dagmar Bublíková ◽  
Štěpán Jeníček ◽  
Kateřina Opatová ◽  
Bohuslav Mašek
Keyword(s):  
Heat Treatment ◽  
Cooling Rate ◽  
Microstructure Evolution ◽  
Retained Austenite ◽  
Volume Fraction ◽  
High Strength ◽  
Quenching And Partitioning ◽  
Alloying Additions ◽  
New Procedures ◽  
Strength And Ductility

Today’s advanced steels are required to possess high strength and ductility. This can be accomplished by producing appropriate microstructures with a certain volume fraction of retained austenite. The resulting microstructure depends on material’s heat treatment and alloying. High ultimate strengths and sufficient elongation levels can be obtained by various methods, including quenching and partitioning (Q&P process). The present paper introduces new procedures aimed at simplifying this process with the use of material-technological modelling. Three experimental steels have been made and cast for this investigation, whose main alloying additions were manganese, silicon, chromium, molybdenum and nickel. The purpose of manganese addition was to depress the Ms and Mf temperatures. The Q&P process was carried out in a thermomechanical simulator for better and easier control. The heat treatment parameters were varied between the sequences and their effect on microstructure evolution was evaluated. They included the cooling rate, partitioning temperature and time at partitioning temperature. Microstructures including martensite with strength levels of more than 2000 MPa and elongation of 10–15 % were obtained.

Superplastic behaviour and microstructure evolution of a fine-grained TA15 titanium alloy

Rare Metals ◽  
2009 ◽  
Vol 28 (5) ◽  
pp. 523-527 ◽  
Author(s):  
Zhanglong Zhao ◽  
Hongzhen Guo ◽  
Li Chen ◽  
Zekun Yao
Keyword(s):  
Titanium Alloy ◽  
Microstructure Evolution ◽  
Fine Grained ◽  
Superplastic Behaviour ◽  
Ta15 Titanium Alloy
Sign in / Sign up

Export Citation Format

Share Document