Mechanical Behavior of Multi-Phase Steels Comprising Retained Austenite

The retained austenite (RA) in advanced high-strength steel (AHSS) grades, such as dual-phase (DP) steels, plays an important role on their formability. Thanks to the transformation-induced plasticity (TRIP) effect that occurs during the mechanically induced transformation of RA into martensite, additional ductility is obtained. Martensite has a higher flow stress than austenite; hence, the transformation results in an apparent hardening, which is beneficial for the stability of deformation. The stability of RA at a given temperature strongly depends on its carbon content, which, in AHSS, is not uniform but distributed. The aim of this study is to build a model that predicts the transformation as well as TRIP in a DP steel grade with RA. A physics-based kinetic model is presented that captures the transformation of retained austenite based on the thermodynamic driving force of the applied stress. A direct analytical estimate of transformation plasticity is provided, which is consistent with the kinetic model. Transformation kinetics is incorporated in a self-consistent, mean-field homogenization-based constitutive model. Finally, an indication of the effect of transformation of retained austenite on formability is given.

Successive Grinding and Polishing Effect on the Retained Austenite in the Surface of 42CrMo4 Steel

Low-alloy 42CrMo4 steels were studied by 57Fe Mössbauer spectroscopy (MS), X-ray diffractometry (XRD), and Energy Dispersive X-ray Spectroscopy (EDS) measurements. The investigations were performed on metallographic samples, which were subjected to a series of successive grinding and polishing with a progressively finer grit. Conversion X-ray Mössbauer spectroscopy (CXMS) was used to determine the occurrence of austenite in steel samples. It is a unique method detecting the austenite content very sensitively. Six samples with different surface preparation were investigated, starting with 4.8% of austenite on an as-cut sample, and a large decrease in the retained austenite to 2.6% was observed after the first grinding of a hardened cut sample. Additionally, an unexpectedly large decrease in the austenite content to 2.3% was found due to the final polishing. A second time applied successive grinding and polishing of all samples resulted in identical austenite content determined by CXMS of approx. 5%, which proved the applicability of the CXMS method. Generally, the result calls attention to the importance of preparation of metallurgical samples by grinding and polishing where the results can vary significantly on the level of surface processing.

The Impact of Retained Austenite on the Mechanical Properties of Bainitic and Dual Phase Steels

This paper presents the microstructural changes and mechanical properties of carbide-free bainitic steel subjected to various heat treatment processes and compares these results with similarly treated ferritic–pearlitic steel. A key feature of the investigated steel, which is common among others described in the literature, is that the Si content in the developed steel was >1 wt.% to avoid carbide precipitation in the retained austenite during the bainitic transformation. The phase identification before and after various heat treatment conditions was carried out based on microstructural observations and x-ray diffraction. Hardness measurements and tensile tests were conducted to determine the mechanical properties of the investigated materials. In addition, following the tensile tests, the fracture surfaces of both types of steels were analyzed. Changing the bainitic transformation temperature generated distinct volume fractions of retained austenite and different values of mechanical strength properties. The mechanical properties of the examined steels were strongly influenced by the volume fractions and morphological features of the microstructural constituents. It is worth noting that the bainitic steel was characterized by a high ultimate tensile strength (1250 MPa) combined with a total elongation of 18% after austenitizing and continuous cooling. The chemical composition of the bainitic steel was designed to obtain the optimal microstructure and mechanical properties after hot deformation followed by natural cooling in still air. Extensive tests using isothermal transformation to bainite were conducted to understand the relationships between transformation temperature and the resulting microstructures, mechanical properties, and fracture characteristics. The isothermal transformation tests indicated that the optimal relationship between the sample strength and total elongation was obtained after bainitic treatment at 400 °C. However, it should be noted that the mechanical properties and total elongation of the bainitic steel after continuous cooling differed little from the condition after isothermal transformation at 400 °C.

Enhanced Strength and Ductility by Introducing Nanobainitic Ferrite in Bainitic Steel Used in Sports Equipment

The mechanical properties of carbide-free bainitic steels used in sports equipment were investigated. The nanobainitic ferrite was introduced in bainitic steel to enhance the stability of blocky retained austenite (RA). The blocky RA formed in bainitic austempering process was coarse and led to poor mechanical properties. By introducing the nanobainitic ferrite into blocky RA, the yield strength was improved remarkably, which was increased from 706 to 1180 MPa. Furthermore, the total elongation was almost twice the value compared to the traditional bainitic treatment. The improved mechanical properties were attributed to the enhanced stability of blocky RA. Furthermore, the increased carbon content in RA derived from the carbon dissolved in bainitic ferrite and the carbon trapped in dislocation or Cottrell atmosphere.

Comparison of the Hardness-Toughness Relationship of Medium-Mn Steels after Q&T and Q&P Treatments*

In contrast to quenching and tempering (Q&T), with quenching to room temperature, quenching and partitioning (Q&P) usually applies quenching to a temperature between Ms and room temperature. To stabilize a sufficient amount of retained austenite (RA), carbon diffusion from martensite into austenite and a prevention of cementite formation takes place during the successive partitioning step. Larger amount of RA, and its transformation into martensite during plastic deformation, provides Q&P treated steels with an enhanced combination of strength and ductility. In this investigation, the effect of different Q&T and Q&P treatments on the hardness-toughness relationship was determined. These results are compared with the RA contents and mechanical properties provided by tensile testing. The obtained results clearly demonstrate that the optimum parameters for strength and ductility do not match with the best combinations of hardness and toughness. Furthermore, the stability of the RA plays an important role in the understanding of toughness properties of the investigated Q&P steels.