Microstructure and properties of Cu-10 wt.% Al bronze obtained by high-energy mechanical milling and spark plasma sintering

2022 ◽  
pp. 131671
Author(s):  
Dina V. Dudina ◽  
Tatyana F. Grigoreva ◽  
Vyacheslav I. Kvashnin ◽  
Evgeniya T. Devyatkina ◽  
Sergey V. Vosmerikov ◽  
...  
Keyword(s):  
Spark Plasma Sintering ◽  
Mechanical Milling ◽  
High Energy ◽  
Microstructure And Properties ◽  
Plasma Sintering ◽  
Spark Plasma

The Cu Matrix Strengthened by TiH2–C In-Situ Synthesized via Mechanical Milling and Spark Plasma Sintering

2021 ◽  
Vol 21 (4) ◽  
pp. 2687-2691
Author(s):  
Nguyen Thi ◽  
Hoang Oanh ◽  
Nguyen Hoang Viet
Keyword(s):  
Spark Plasma Sintering ◽  
Mechanical Milling ◽  
Sintering Temperature ◽  
Annealing Treatment ◽  
High Energy ◽  
Composite Powders ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Tic Nanoparticles

The present work is focused on the fabrication and the investigation of microstructures of copperbased TiC nanocomposites produced by mechanical milling in a high energy planetary ball mill. TiH2, carbon and copper powders were used as starting materials in which In-Situ reaction between carbon and TiH2 occurs to form TiC nanoparticles. The mixture powders of Cu–TiH2–C were milled for 12 h at 450 rpm in Argon gas. Annealing treatment process at 950 °C for 2 h was applied for as-milled composite powders to enhance In-Situ reaction. The consolidation of composite powders was conducted by spark plasma sintering under uniaxial pressing of 70 MPa. Sintering procedure was done at 950 and 1000 °C for 5 min. The results indicated that as TiC nanoparticles are formed after sintering at 950 °C and the TiC particles are increased up at higher sintering temperature of 1000 °C. Fracture surface of sintered samples shows ductile mode. HR-TEM image showed the crystal size of copper was about 10 nm for sample sintered at 1000 °C. The hardness and relative density of the nanocomposites increase when increasing sintering temperature.

Superplastic Deformation of Nano-Sized α-Sialon Ceramics

2007 ◽  
Vol 336-338 ◽  
pp. 1001-1004 ◽  
Author(s):  
Xin Xu ◽  
Toshiyuki Nishimura ◽  
Naoto Hirosaki ◽  
Rong Jun Xie ◽  
Yoshinobu Yamamoto ◽  
...  
Keyword(s):  
Liquid Phase ◽  
Spark Plasma Sintering ◽  
Microstructural Evolution ◽  
Mechanical Milling ◽  
Superplastic Deformation ◽  
Transient Liquid Phase ◽  
High Energy ◽  
Post Annealing ◽  
Plasma Sintering ◽  
Spark Plasma

In previous report, we succeeded in preparing dense nano-sized ceramics with the composition of Y- α-sialon (m=1.35, n=0.675) by high-energy mechanical milling followed by spark plasma sintering. The superplastic deformation of the obtained nano-ceramics was studied in this report. A good ductility of the nano-sized ceramics has been confirmed, which arised from the nano-sized grains and large amount of transient liquid phase. The effects of deformation on the phase and microstructural evolution were also studied. The nano-sized grains promoted the formation of elongated α-sialon grains during post-annealing at 1850oC for 3 h, which would strengthen and toughen the deformed ceramics.

Fabrication of Silicon Nitride Nano-Ceramics by High-Energy Mechanical Milling and Spark Plasma Sintering

2005 ◽  
Vol 287 ◽  
pp. 166-170 ◽  
Author(s):  
Xin Xu ◽  
Toshiyuki Nishimura ◽  
Naoto Hirosaki ◽  
Rong Jun Xie ◽  
Yoshinobu Yamamoto
Keyword(s):  
Silicon Nitride ◽  
Low Temperature ◽  
Spark Plasma Sintering ◽  
Mechanical Milling ◽  
Crystalline Silicon ◽  
High Energy ◽  
Milling Process ◽  
Charge Ratio ◽  
Plasma Sintering ◽  
Spark Plasma

The fabrication of dense Si3N4 nano-ceramics via a high-energy mechanical milling process and subsequent spark plasma sintering (SPS) was reported in this paper. A thermodynamically stable β-Si3N4 powder mixed with 5-mol% Y2O3 and 2-mol% Al2O3 was used as starting powders for high-energy mechanical milling. Milling resulted in the significant decrease of crystalline size and the amorphization of the starting powders. Based on XRD measurements, the amount of the amorphous phase and the grain sizes of the remaining crystalline silicon nitride depended on the charge ratio. Milled powders could be SPSed at relatively low temperature. A homogenous dense silicon nitride ceramics with grain diameter of about 70 nm could be fabricated through SPS at a low temperature of 1600oC for 5 min. The significant decrease of grain size greatly increased the hardness of obtained ceramics.

Fabrication of β-sialon nanoceramics by high-energy mechanical milling and spark plasma sintering

2005 ◽  
Vol 16 (9) ◽  
pp. 1569-1573 ◽  
Author(s):  
Xin Xu ◽  
Toshiyuki Nishimura ◽  
Naoto Hirosaki ◽  
Rong-Jun Xie ◽  
Yoshinobu Yamamoto ◽  
...  
Keyword(s):  
Spark Plasma Sintering ◽  
Mechanical Milling ◽  
High Energy ◽  
Plasma Sintering ◽  
Spark Plasma
Sign in / Sign up

Export Citation Format

Share Document