Dynamic deformation behavior of a high reinforcement content TiB2/Al composite at high strain rates

2008 ◽  
Vol 487 (1-2) ◽  
pp. 536-540 ◽  
Author(s):  
Dezhi Zhu ◽  
Gaohui Wu ◽  
Guoqin Chen ◽  
Qiang Zhang
Keyword(s):  
Deformation Behavior ◽  
High Strain ◽  
Dynamic Deformation ◽  
Strain Rates ◽  
High Strain Rates ◽  
Reinforcement Content ◽  
Al Composite ◽  
Dynamic Deformation Behavior

Dynamic Deformation Behavior of As-Extruded Mg-Gd-Y Magnesium Alloy and the Microstructural Evolution

2011 ◽  
Vol 284-286 ◽  
pp. 1579-1583
Author(s):  
Ping Li Mao ◽  
Zheng Liu ◽  
Chang Yi Wang ◽  
Feng Wang
Keyword(s):  
Magnesium Alloy ◽  
Strain Rate ◽  
Deformation Behavior ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
Dynamic Deformation ◽  
Strain Rates ◽  
Compression Axis ◽  
Deformation Localization ◽  
Dynamic Deformation Behavior

The dynamic deformation behavior of an as-extruded Mg-Gd-Y magnesium alloy was studied by using Split Hopkinson Pressure Bar (SHPB) apparatus under high strain rates of 102 s-1 to 103s-1 in the present work, in the mean while the microstructure evolution after deformation were inspected by OM and SEM. The results demonstrated that the material is not sensitive to the strain rate and with increasing the strain rate the yield stress of as-extruded Mg-Gd-Y magnesium alloy has a tendency of increasing. The microstructure observation results shown that several deformation localization areas with the width of 10mm formed in the strain rates of 465s-1 and 2140s-1 along the compression axis respectively, and the grain boundaries within the deformation localization area are parallel with each other and are perpendicular to the compression axis. While increasing the strain rate to 3767s-1 the deformation seems become uniform and all the grains are compressed flat in somewhat. The deformation mechanism of as-extruded Mg-Gd-Y magnesium alloy under high strain rate at room temperature was also discussed.

Deformation behavior of Al/Cu in-situ metal-intermetallic laminates at low and high strain rates

2021 ◽  
pp. 159767
Author(s):  
Kartheek. S.M. Sonti ◽  
Biswaranjan Dash ◽  
K.V. Vamsi ◽  
H. Bandyopadhyay ◽  
B. Ravisankar ◽  
...  
Keyword(s):  
Deformation Behavior ◽  
High Strain ◽  
Strain Rates ◽  
High Strain Rates

scholarly journals On the Capability of Logarithmic-Power Model for Prediction of Hot Deformation Behavior of Alloy 800H at High Strain Rates

2019 ◽  
Vol 38 (2019) ◽  
pp. 84-91 ◽  
Author(s):  
E. Shafiei ◽  
A. Soltani Tehrani
Keyword(s):  
Flow Stress ◽  
Constitutive Equation ◽  
Hot Deformation ◽  
Deformation Behavior ◽  
High Strain ◽  
Power Model ◽  
Strain Rates ◽  
Hot Deformation Behavior ◽  
High Strain Rates ◽  
Alloy 800H

AbstractIn this study, the logarithmic-power model has been used to predict hot deformation behavior of alloy 800H at high temperatures. This is for the first time that the logarithmic-power model is examined to model the flow stress curves with negligible flow softening at high strain rates. To this end, flow stress curves of alloy 800H obtained at deformation temperatures from 850°C to 1050°C and at strain rates of 5 and 10 S−1 were employed. The Johnson–Cook model and Shafiei constitutive equation were also used to prove the accuracy of the logarithmic-power model in prediction of flow stress curves of alloy 800H. Evaluation of mean error of flow stress at different deformation conditions showed that the logarithmic-power model can give a more precise estimation of flow stress curves than Johnson–Cook model. Furthermore, it was found out that the accuracy of the Logarithmic-power model and Shafiei constitutive equation was roughly the same in terms of maximum errors obtained in prediction of flow stress curves. Accordingly, it can be concluded that the logarithmic-power model can be employed as a comprehensive model for a wide range of deformation conditions.

Sign in / Sign up

Export Citation Format

Share Document