Effect of initial base metal temper on microstructure and mechanical properties of friction stir processed Al-7B04 alloy

2016 ◽  
Vol 650 ◽  
pp. 396-403 ◽  
Author(s):  
Yu Chen ◽  
Hua Ding ◽  
Zhihui Cai ◽  
Jingwei Zhao ◽  
Jizhong Li
Keyword(s):  
Mechanical Properties ◽  
Base Metal ◽  
Friction Stir ◽  
Microstructure And Mechanical Properties ◽  
Initial Base

Synergetic Effect of ECAP and Friction Stir Welding on Microstructure and Mechanical Properties of Aluminium Sheets

2010 ◽  
Vol 667-669 ◽  
pp. 505-510
Author(s):  
Ilya Nikulin ◽  
Alla Kipelova ◽  
Sergey Malopheyev ◽  
Rustam Kaibyshev
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Friction Stir Welding ◽  
Base Metal ◽  
Synergetic Effect ◽  
Aluminum Matrix ◽  
Friction Stir ◽  
Microstructure And Mechanical Properties ◽  
Average Grain Size

Friction stir welding (FSW) was used to join the submicrocrystalline (SMC) grained Al-Cu-Mg-Ag sheets produced by equal channel angular pressing (ECAP) followed by hot rolling (HR). The effect of SPD and FSW on the microstructure and mechanical properties in the zone of base metal, as well as in the stirred zone (SZ) were examined. In addition, effect of standard heat treatment on microstructure and mechanical properties in these zones was considered. A refined microstructure with an average grain size of ~ 0.6 m and a portion of high-angle grain boundaries (HAGBs) of ~0.67 was produced in sheets by ECAP followed by HR at 250°C. The microcrystalline grained structure with average grain size of ~2.3 mm was found in joint weld. The moderate mechanical properties were revealed in SMC sheets and joint welds. Heat treatment considerably increases strength of the base metal as well as the joint welds. The higher strength of the alloy after T6 temper is attributed to the dense precipitations of  dispersoids having plate-like shape which are uniformly distributed within aluminum matrix. It was observed that FSW can produce full strength weld both in the tempered and in the un-tempered conditions.

scholarly journals A Study on Microstructure and Mechanical Properties of Micro Friction Stir Welded Ultra-Thin Al-1060 Sheets by the Shoulderless Tool

Metals ◽  
2019 ◽  
Vol 9 (5) ◽  
pp. 507 ◽  
Author(s):  
Changqing Zhang ◽  
Weijie Wang ◽  
Xin Jin ◽  
Chen Rong ◽  
Zhuo Qin
Keyword(s):  
Mechanical Properties ◽  
Base Metal ◽  
Heat Input ◽  
Metal Flow ◽  
Friction Stir ◽  
Aluminum Sheets ◽  
Microstructure And Mechanical Properties ◽  
Welding Defects ◽  
Plastic Forming ◽  
Conventional Tool

The welding tool is the key of micro friction stir welding (μFSW), which affects the heat input and the plastic forming of weld metal. In this paper, 0.8-mm-thick ultra-thin 1060-H24 aluminum sheets μFSW butt joints were used to compare and analyze the influence of the conventional tool and shoulderless tool on weld shaping, microstructure and mechanical properties. Besides, by measuring the axial force, transverse force and weld temperature in μFSW process, the influence of these two different tools on the heat input and metal flow mechanism of the weld were analyzed. The results show that the weld generated by the shoulderless tool has narrower width, less heat input and metal involved in plastic forming resulting in smaller HAZ (heat affected zone). The hardness of NZ (nugget zone) is obviously increased compared with that of the base metal. The highest tensile strength can reach 108.6 MPa, accounting for 78.6% of the base metal and 117.3% of the joint by the conventional tool. But the welding defects have to be overcome for industrial application of the shoulderless tool.

Sign in / Sign up

Export Citation Format

Share Document