Development of a high temperature flow stress model for AerMet 100 covering several orders of magnitude of strain rate

2016 ◽  
Vol 657 ◽  
pp. 26-32 ◽  
Author(s):  
M. Shakib ◽  
K.M. Perkins ◽  
S.E. Bray ◽  
C.R. Siviour
Keyword(s):  
High Temperature ◽  
Flow Stress ◽  
Strain Rate ◽  
Stress Model ◽  
Flow Stress Model

Study on High Temperature Flow Stress Model of As-cast SA508-3 Low Alloy Steel

2020 ◽  
Vol 831 ◽  
pp. 25-31
Author(s):  
Pan Fei Fan ◽  
Jian Sheng Liu ◽  
Hong Ping An ◽  
Li Li Liu
Keyword(s):  
High Temperature ◽  
Flow Stress ◽  
Strain Rate ◽  
Alloy Steel ◽  
Flow Behavior ◽  
Peak Stress ◽  
Stress Model ◽  
Low Alloy Steel ◽  
Two Stage ◽  
Flow Stress Model

In order to obtain the high temperature flow behavior of as-cast SA508-3 low alloy steel, the stress-strain curves of steel are obtained by Gleeble thermal simulation compression test at deformation temperature 800°C-1200°C and strain rate 0.001s-1-1s-1. Based on Laasraoui two-stage flow stress model, a high temperature flow stress model is established by multiple linear regression method. The results show that the peak stress characteristics are not obvious at low temperature and high strain rate, which is a typical dynamic recovery characteristic. Meanwhile, the peak stress characteristics are obvious at high temperature and low strain rate, which is a typical dynamic recrystallization characteristic. By means of the comparisons between experiments and calculations, the Laasraoui two-stage flow stress model can truly reflect flow behavior of steel at high temperature, which provides theoretical guidance for the hot deformation of the steel.

High Temperature Deformation Behavior of Ti-7333 Titanium Alloy and its Flow Stress Model

2012 ◽  
Vol 538-541 ◽  
pp. 945-950 ◽  
Author(s):  
Jiang Kun Fan ◽  
Hong Chao Kou ◽  
Min Jie Lai ◽  
Bin Tang ◽  
Hui Chang ◽  
...  
Keyword(s):  
Titanium Alloy ◽  
High Temperature ◽  
Flow Stress ◽  
Strain Rate ◽  
Deformation Behavior ◽  
High Temperature Deformation ◽  
Temperature Deformation ◽  
Stress Model ◽  
Compression Tests ◽  
Flow Stress Model

The effects of processing parameters on deformation behavior of a new near β titanium alloy were investigated by using compression tests. The experiments were carried out in the Gleeble-3800 thermal and mechanical simulator in the temperature range of 770-970°C and strain rate range of 10-3-10s-1, and height direction reduction of 70%. The results show that the flow stress of Ti-7333 titanium alloy increases obviously with the strain and reaches a peak, then decreases to a steady value. The steady and peak stress significantly decreases with the increase of deformation temperature and decrease of strain rate. The flow stress model of Ti-7333 titanium alloy during high temperature deformation was established by using the regression method. The average relative difference between the calculated and experimental flow stress is 6.33%. The flow stress model can efficiently predict the deformation behavior of Ti-7333 titanium alloy during high temperature deformation.

A Constitutive Equation Coupling the Grain Size during the High Temperature Deformation of Ti-6.62Al-5.14Sn-1.82Zr Alloy

2007 ◽  
Vol 561-565 ◽  
pp. 155-158 ◽  
Author(s):  
Jiao Luo ◽  
Miao Quan Li ◽  
Y.Q. Hu
Keyword(s):  
Grain Size ◽  
High Temperature ◽  
Flow Stress ◽  
Constitutive Equation ◽  
Steady Flow ◽  
Maximum Error ◽  
High Temperature Deformation ◽  
Temperature Deformation ◽  
Stress Model ◽  
Flow Stress Model

A constitutive equation has been established to describe the effect of grain size on the deformation behavior of Ti-6.62Al-5.14Sn-1.82Zr alloy during the high temperature. In this paper, firstly a steady flow stress model is proposed, and a function relating to the grain size is introduced to modify the steady flow stress model. Meanwhile, a microstructure model established by the fuzzy neural network method is applied to calculate the grain size of prior α phase during the high temperature deformation of Ti-6.62Al-5.14Sn-1.82Zr alloy. The calculated flow stress using the present constitutive equation shows a good agreement with the experimental flow stress of the Ti-6.62Al-5.14Sn-1.82Zr alloy. The relative maximum error was not more than 15%.

Sign in / Sign up

Export Citation Format

Share Document