Damage analysis of hot-rolled AZ31 Mg alloy sheet during uniaxial tensile testing under different loading directions

2018 ◽  
Vol 710 ◽  
pp. 289-299 ◽  
Author(s):  
Weiying Huang ◽  
Qinghuan Huo ◽  
Zhengwu Fang ◽  
Zhenyu Xiao ◽  
Yong Yin ◽  
...  
Keyword(s):  
Tensile Testing ◽  
Alloy Sheet ◽  
Mg Alloy ◽  
Uniaxial Tensile ◽  
Damage Analysis ◽  
Uniaxial Tensile Testing ◽  
Az31 Mg Alloy ◽  
Hot Rolled

The Microstructure Evolution and Twinning Characterization of AZ31 Mg Alloy Sheet in Low-Temperature Bending Process

2013 ◽  
Vol 690-693 ◽  
pp. 16-19
Author(s):  
Jun Wei Liu ◽  
Shi Qiang Lu ◽  
Ke Lu Wang ◽  
Gui Fa Li ◽  
Xuan Xiao
Keyword(s):  
Low Temperature ◽  
Microstructure Evolution ◽  
Room Temperature ◽  
Alloy Sheet ◽  
Mg Alloy ◽  
Az31 Mg Alloy ◽  
Bending Process ◽  
Hot Rolled ◽  
The Relationship

The relationship among stress, cavities and twinning in the room-temperature bending process of hot-rolled AZ31 Mg alloy sheet was researched. It can be seen that the mount of twins which was tightly affected by stress value increases with the distance to press point. Otherwise, the cavities and twinning which seem totally independent, in fact affect with each other. Some cavities were hindered by twins and can not further grow up. Then, the relationship between slip and twinning was also roughly discussed. The dislocation lines in twins can be thought to release the stress focus and were beneficial for deformation.

Mechanical behavior of chemically treated ostrich pericardium subjected to uniaxial tensile testing: influence of the suture

2002 ◽  
Vol 62 (1) ◽  
pp. 73-81 ◽  
Author(s):  
J. M. García Páez ◽  
A. Carrera ◽  
E. Jorge Herrero ◽  
I. Millán ◽  
A. Rocha ◽  
...  
Keyword(s):  
Mechanical Behavior ◽  
Tensile Testing ◽  
Uniaxial Tensile ◽  
Uniaxial Tensile Testing ◽  
Chemically Treated

A Novel MEMS-Based Technique for In-Situ Characterization of Freestanding Nanometer Scale Thin Films Inside SEM and TEM

2001 ◽  
Author(s):  
M. A. Haque ◽  
M. T. A. Saif
Keyword(s):  
Thin Films ◽  
Tensile Testing ◽  
Uniaxial Tensile ◽  
Aluminum Specimen ◽  
Sem And Tem ◽  
Uniaxial Tensile Testing ◽  
Testing Facility ◽  
Film Specimen ◽  
On Chip

Abstract We present a MEMS-based technique for in-situ uniaxial tensile testing of freestanding thin films inside SEM and TEM. It integrates a freestanding thin film specimen with MEMS force sensors and structures to produce an on-chip tensile testing facility. Cofabrication of the specimen with force and displacement measuring mechanisms produces the following unique features: 1) Quantitative experimentation can be carried out in both SEM and TEM, 2) No extra gripping mechanism is required, 3) Specimen misalignment can be eliminated, 4) Pre-stress in specimen can be determined, and 5) Specimens with micrometer to nanometer thickness can be tested. We demonstrate the technique by testing a 200-nanometer thick Aluminum specimen in-situ in SEM. Significant strengthening and anelasticity were observed at this size scale.

scholarly journals Length Scale and Aging Effect on the Mechanical Properties of a 63Sn-37Pb Solder Alloy

2000 ◽  
Author(s):  
T. Jesse Lim ◽  
Wei-Yang Lu
Keyword(s):  
Ultimate Strength ◽  
Tensile Testing ◽  
Failure Strain ◽  
Aging Effect ◽  
Uniaxial Tensile ◽  
Strain Response ◽  
Stress Strain ◽  
Uniaxial Tensile Testing ◽  
Aging Conditions ◽  
Strain Responses

Abstract In this work, uniaxial tensile testing of a 63Sn-37Pb alloy with different specimen sizes and aging conditions had been carried out. Although the stress-strain responses of different specimen sizes and aging conditions differs, the ultimate strength of the specimens with 16 hours, 100°C aging are similar for the sizes tested. The specimens with 25 days, 100°C aging have different stress-strain response with different sizes, and have a lower ultimate strength and higher failure strain compared to 16 hours, 100°C aging specimens.

Sign in / Sign up

Export Citation Format

Share Document