Time-dependent wellbore instability and ballooning in naturally fractured formations

2004 ◽  
Vol 43 (1-2) ◽  
pp. 113-128 ◽  
Author(s):  
Ole A. Helstrup ◽  
Zhixi Chen ◽  
Sheik S. Rahman
2021 ◽  
Author(s):  
Jingyou Xue ◽  
Kenji Furui

<p>Wellbore instability is one of the most serious drilling problems increasing well cost in well construction processes. It is widely known that many wellbore instability problems are reported in shale formations where water sensitive clay mineral exist. The problems become further complicated when the shale exhibits variation in strength properties along and across bedding planes. In this study, a coupled thermal-hydro-mechanical-chemical (THMC) model was developed for time-dependent anisotropic wellbore stability analysis considering chemical interactions between swelling shale and drilling fluids, thermal effects, and poro-elastoplastic stress-strain behaviors.</p><p>The THMC simulator developed in this work assumes that the shale formation behaves as an ion exchange membrane where swelling depends on chemical potential of drilling fluids invading from the wellbore to the pore spaces. The time-dependent chemical potential changes of water within the shale are evaluated using an analytical diffusion equation resulting in the evolution of swelling strain around the wellbore. On the other hand, the thermal and pressure diffusion equations are evaluated numerically by finite differences. The stress changes associated with thermal, hydro, and chemical effects are coupled to the 3D poroelastoplastic finite element model. The effects of bedding planes are also taken into account in the FEM model through the crack tensor method in which the normal and tangential stiffnesses of the bedding planes have stress dependency. The failure of the formation rock is judged based on the critical plastic strain limit.</p><p>The numerical analysis results indicate that the rock strength anisotropy induced by the existence of bedding planes is the most important factor influencing the stability of the wellbore among various THMC process parameters investigated in this work. The numerical results also reveal that an established theory to orient the wellbore in the direction of the minimum principal stress is not always a favorable option when the effect of the anisotropy of in-situ stresses and the distribution angle of bedding planes cancel out each other. Depending on both the distribution angle of bedding plane and ratio of the vertical to the horizontal stress, the trend of minimum mud pressure showed a great variation as predicted by the yield and failure criterion implemented in the model. Furthermore, the analysis results reveal that the distribution and evolution of plastic strains caused by the THMC processes have the time dependency, which can be controlled by the temperature and salinity of the drilling fluids.</p><p>The numerical wellbore stability analysis model considering shale swelling and bedding plane effects provides an effective tool for designing optimum well trajectories and determining safe mud weight windows for drilling complex shale formations. The time-dependent margins of safe mud weight window of drilling can be fine-tuned when the interaction among various parameters is fully considered as the THMC processes.</p>


2021 ◽  
Author(s):  
Bassey Akong ◽  
Samuel Orimoloye ◽  
Friday Otutu ◽  
Goodluck Mfonnom ◽  
Akinwale Ojo ◽  
...  

Abstract Drilling of deviated development wells in O-field X has proven to be challenging. Drilling experience in several wells within the field has different issues of wellbore instability, most recent is when traversed through a pre-existing/naturally fractured intervals. Numerous lost-time incidents related to wellbore instability-related problems were experienced, ranging from tight hole (remedied by reaming) to Overpulls, pack-off followed by stuck pipe, fill on-bottom to difficulties in running casing, and tensile cavings to high gas associated with drilling breaks. These problems were observed particularly when drilling previous and current wells in the O-field X. Many of the wells in O-field X were drilled with water-based mud (WBM) for top-hole and POBM for intermediate hole section. However, drilling the most recent well became more challenging with issues of severe losses just below the 13-3/8inch shoe where an interbedded lignite formation characterized with pre-existing fractures was drilled through. Faced with continual non-productive time (NPT), the predrill GeoMechanical report was immediately reviewed coupled with the stress caging procedure adopted to further mitigate the loss circulation wellbore instability problem. The recommendations arising from the comprehensive review of the GeoMechanical window, stress caging and drilling experience analyses was immediately implemented to improve performance which has helped in drilling the well to final completion. This paper highlights the importance of integrating GeoMechanics, stress caging and with proper drilling practices which has helped in delivery of the candidate well. A full-scale GeoMechanical window review was proactively adopted considering the mid-line collapse gradient approach for unconsolidated, naturally fracture formations and critical depleted intervals. All the above strategies were adopted, which assisted in safe delivery of candidate well in O-field X.


2009 ◽  
Vol 12 (2) ◽  
pp. 119-130 ◽  
Author(s):  
Talal M. Al-Bazali ◽  
Jianguo Zhang ◽  
Chris Wolfe ◽  
Martin E. Chenevert ◽  
Mukul M. Sharma

2021 ◽  
Author(s):  
Jianguo Zhang ◽  
Alan Rodgerson ◽  
Stephen Edwards

Abstract Wellbore instability and lost circulation are two major sources of non-productive time (NPT) in drilling operations worldwide. Non-aqueous fluid (NAF) is often chosen to mitigate this and minimize the chemical effect on wellbore instability in reactive shales. However, it may inadvertently increase the risk of losses. A simple method to optimize internal phase salinity (IPS) of NAF is presented to improve wellbore stability and mitigate the increased possibility of losses. Field cases are used to demonstrate the effects of salinity on wellbore instability and losses, and the application of the proposed method. IPS is optimized by managing bidirectional water movement between the NAF and shale formation via semi-permeable membrane. Typically, higher shale dehydration is designed for shallow reactive shale formation with high water content. Whereas, low or no dehydration is desired for deep naturally fractured or faulted formation by balancing osmotic pressure with hydrostatic pressure difference between mud pressure and pore pressure. The simple approach to managing this is as follows: The water activity profile for the shale formation (aw,shale) is developed based on geomechanical and geothermal information The water activity of drilling fluid (aw,mud) is defined through considering IPS and thermal effects The IPS of NAF is manipulated to manage whether shale dehydration is a requirement or should be avoided If the main challenge is wellbore instability in a chemically reactive shale, then the IPS should be higher than the equivalent salinity of shale formation (or aw,shale > aw, mud) If the main challenge is losses into non-reactive, competent but naturally fractured or faulted shale, then IPS should be at near balance with the formation equivalent salinity (or aw, shale ≈ aw, mud) It is important that salt (e.g. calcium chloride – CaCl2) addition during drilling operations is done judiciously. The real time monitoring of salinity variations, CaCl2 addition, water evaporation, electric stability (ES), cuttings/cavings etc. will help determine if extra salt is required. The myth of the negative effects of IPS on wellbore instability and lost circulation is dispelled by analyzing the field data. The traditional Chinese philosophy: "following Nature is the only criteria to judge if something is right" can be applied in this instance of IPS optimization. A simple and intuitive method to manage IPS is proposed to improve drilling performance.


2021 ◽  
Author(s):  
Arnaud Regis Kamgue Lenwoue ◽  
Jingen Deng ◽  
Yongcun Feng ◽  
Naomie Beolle Songwe Selabi

Abstract Wellbore instability is one of the most important causes of Non-Productive Time causing billions of dollars of losses every year in the petroleum industry. During the drilling operations, the drilling mud is generally utilized to maintain the wellbore stability. However, the drilling mud is subjected to fluctuations caused by several processes such as the drill string vibration cyclic loads which can result into wellbore instability. In this paper, a nonlinear finite element software ABAQUS is utilized as the numerical simulator to evaluate the time dependent pore pressure and stress distribution around the wellbore after integration of drill string vibration cyclic loads. A MATLAB program is then developed to investigate the wellbore stability by computation of the time dependent wellbore collapse pressure and fracture pressure. The numerical results showed that the safe mud window which was initially constant became narrower with the time after integration of vibration cyclic load. The collapse pressure without vibration cyclic load increased by 14.33 % at the final simulation time while the fracture pressure decreased by 13.80 %. Interestingly, the safe mud windows widened with the increase of the normalized wellbore radius as the wellbore fracture pressure increased and the collapse pressure decreased. This study provides an insight into the coupling of the wellbore stability and the continuous cyclic loads generated by drill string vibrations which is an aspect that has been rarely discussed in the literature.


Sign in / Sign up

Export Citation Format

Share Document