Self-similar microstructural evolution of dendritic solid–liquid mixtures during coarsening

2009 ◽  
Vol 60 (10) ◽  
pp. 839-842 ◽  
Author(s):  
J.L. Fife ◽  
P.W. Voorhees
2012 ◽  
Vol 192-193 ◽  
pp. 238-245 ◽  
Author(s):  
Hong Yu Xu ◽  
Ze Sheng Ji ◽  
Zhen Yu Wang

In this paper, chip recycling technology combined with SIMA method which is called CR-SIMA method was adopted to prepare semi-solid billets. AZ91D magnesium alloy was refined by Er and its microstructural evolution was investigated during semi-solid isothermal treatment. The results show that Er can improve the feature of cast structure and decrease the grain size. Moreover, the γ-Mg17Al12 phase is well refined and disperses in the α-Mg matrix. A semisolid microstructure with small and spheroidal primary particles can be obtained after partially remelting. With increasing heating temperature, the dissolution of eutectic Mg17Al12 phase first took place, resulting in the primary dendritic grains coarsening into interconnected non-dendritic grains. With heating continuously, the residual interdendritic γ-Mg17Al12 at the edges of the primary grains melted in succession and the primary grains separated into small polygon grains. During the semi-solid isothermal treatment, the amount of liquid increased until the solid-liquid system reached its equilibrium state. At the same time, owing to the decreasing of interfacial energy, the grains gradually spheroidized and began to grow with a further increasing of the holding time.


Author(s):  
Gary Bolton ◽  
Stephen Stanley

Electrical Impedance Tomography measurement techniques have been applied to a variety of solid-liquid processes in the laboratory and on industrial plant. This paper reviews the advances in the measurement techniques to determine key process information in solid-liquid systems such as concentration mapping, mixture homogeneity, interface detection and suspension velocity. A number of applications to solid-liquid flow applications are presented. The use of the technology for improved design and operation is highlighted, as are the opportunities for on-line sensing for flow measurement, fault detection and process control. A recent development in high-speed electrical imaging has allowed velocity maps to be calculated for fast flowing suspensions (up to 10 ms−1). The methodology for determining mixture homogeneity in both pipeline flows and agitated tanks are summarized. Finally the application of a linear ERT electrode array to identify interfaces during the settling of solid-liquid mixtures is presented.


2019 ◽  
Vol 22 (6) ◽  
pp. 1515-1520 ◽  
Author(s):  
Jiazhi Chen ◽  
Yuan Li ◽  
Xiaotian Chen ◽  
Yuliang Mai ◽  
Minjie Gao ◽  
...  

1993 ◽  
Vol 115 (4) ◽  
pp. 665-675 ◽  
Author(s):  
C. M. Atkinson ◽  
H. K. Kyto¨maa

Ultrasound as a technique for interrogating two-phase mixtures has the advantages of being nonintrusive, it has a very high frequency response, and is able to penetrate typically opaque highly concentrated mixtures. There exists, however, an inherent compromise in the choice of the frequency of the ultrasound between maximizing spatial resolution and ensuring adequate beam penetration. To this end, the propagation of ultrasound in solid-liquid mixtures has been investigated experimentally for a range of frequencies and concentrations of the dispersed phase. The measured attenuation has been shown to depend roughly linearly on frequency for 0.1<kr<0.75 (where the wavenumber k = 2π/λ, and λ and r are the wavelength and particle radius, respectively), and quadratically for kr > 0.75. As a function of solids concentration, the attenuation displays a maximum at a solids fraction of about 30 percent for the present system of silica beads in water. This robust and reproducible result contradicts models of attenuation that rely on linear superposition of single particle effects. The intensity field produced by a circular disk transducer in a two phase medium at kr~1 shows excellent agreement with the Rayleigh integral with a modified wavenumber and attenuation parameter, and it allows for the prediction of the transducer beam geometry in two phase mixtures for a wide range of frequencies and solids fractions. The limitations of ultrasonic wave propagation as a nonintrusive diagnostic technique, in terms of spatial resolution, have been discussed. Acknowledging these limitations, an ultrasonic instrument for determining the velocity of moving particles at or near maximum packing was built. Preliminary results from this prototypical ultrasonic Doppler velocimeter show good agreement with observations of the settling velocity of silica beads at high concentrations.


Sign in / Sign up

Export Citation Format

Share Document