Can interface charge enhance selectivity in tunnel layer passivated contacts? Using negatively charged aluminium oxide capped with dopant free PEDOT or boron doped polysilicon

2021 ◽  
Vol 221 ◽  
pp. 110857
Author(s):  
Gurleen Kaur ◽  
Tanmay Dutta ◽  
Ranjani Sridharan ◽  
Xin Zheng ◽  
Aaron Danner ◽  
...  
Keyword(s):  
Aluminium Oxide ◽  
Interface Charge ◽  
Boron Doped ◽  
Tunnel Layer

Ultra-thin atomic layer deposited aluminium oxide tunnel layer passivated hole-selective contacts for silicon solar cells

2019 ◽  
Vol 191 ◽  
pp. 164-174 ◽  
Author(s):  
Zheng Xin ◽  
Zhi Peng Ling ◽  
Puqun Wang ◽  
Jia Ge ◽  
Cangming Ke ◽  
...  
Keyword(s):  
Solar Cells ◽  
Aluminium Oxide ◽  
Atomic Layer ◽  
Silicon Solar Cells ◽  
Tunnel Layer ◽  
Oxide Tunnel

Preparation of integrated circuits for TEM electromigration in situ studies

1986 ◽  
Vol 44 ◽  
pp. 882-883
Author(s):  
J. V. Maskowitz ◽  
W. E. Rhoden ◽  
D. R. Kitchen ◽  
R. E. Omlor ◽  
P. F. Lloyd
Keyword(s):  
Integrated Circuits ◽  
Crystallographic Orientation ◽  
Silicon Wafers ◽  
Minimum Size ◽  
Test Vehicle ◽  
In Situ Studies ◽  
Boron Doped ◽  
Doped Silicon ◽  
Drill Holes

The fabrication of the aluminum bridge test vehicle for use in the crystallographic studies of electromigration involves several photolithographic processes, some common, while others quite unique. It is most important to start with a clean wafer of known orientation. The wafers used are 7 mil thick boron doped silicon. The diameter of the wafer is 1.5 inches with a resistivity of 10-20 ohm-cm. The crystallographic orientation is (111).Initial attempts were made to both drill and laser holes in the silicon wafers then back fill with photoresist or mounting wax. A diamond tipped dentist burr was used to successfully drill holes in the wafer. This proved unacceptable in that the perimeter of the hole was cracked and chipped. Additionally, the minimum size hole realizable was > 300 μm. The drilled holes could not be arrayed on the wafer to any extent because the wafer would not stand up to the stress of multiple drilling.

A TEM-APFIM INVESTIGATION OF BORON-DOPED Ni3Al

1986 ◽  
Vol 47 (C2) ◽  
pp. C2-209-C2-214 ◽  
Author(s):  
J. A. HORTON ◽  
M. K. MILLER
Keyword(s):  
Boron Doped

Interface-charge-coupled polarization response of Pt-ZnO-BaTiO3-ZnO-Pt heterostructures: Three-layer model expansion

2008 ◽  
Author(s):  
Venkata M. Voora ◽  
Tino Hofmann ◽  
Matthias Brandt ◽  
Michael Lorenz ◽  
Marius Grundmann ◽  
...  
Keyword(s):  
Layer Model ◽  
Interface Charge ◽  
Polarization Response ◽  
Model Expansion

Atomic and Electronic Structure of Boron-Doped Diamond Grain Boundaries Studied by Arhvtem and ab-Initio Calculation

2003 ◽  
Vol 764 ◽  
Author(s):  
Hiroyuki Togawa ◽  
Hideki Ichinose
Keyword(s):  
Ab Initio ◽  
Grain Boundaries ◽  
Ab Initio Calculation ◽  
Structure Model ◽  
Boron Doped Diamond ◽  
Boron Doped ◽  
Transmission Electron ◽  
Diamond Grain ◽  
Electron Energy Loss ◽  
Atomic And Electronic Structure

AbstractAtomic resolution high-voltage transmission electron microscopy and electron energy loss spectroscopy were performed on grain boundaries of boron-doped diamond, cooperated with the ab-initio calculation. Segregated boron in the {112}∑3 boundary was caught by the EELS spectra. The change in atomic structure of the segregated boundary was successfully observed from the image by ARHVTEM. Based on the ARHVTEM image, a segregted structure model was proposed.

Methods to Determine Phytopharmaceuticals in Tobacco and Tobacco Products. 4th Report: A Procedure to Determine Vamidothion and its Metabolites/Methoden zur Bestimmung von Phytopharmaka in Tabak und Tabakerzeugnissen: IV. Mitteilung: Ein Bestimmungsverfahren fuer Vamidothion und seine Metaboliten

1977 ◽  
Vol 9 (2) ◽  
Author(s):  
A.N. Sagredos ◽  
R. Moser
Keyword(s):  
Mass Spectrometry ◽  
Nuclear Magnetic Resonance ◽  
Acetic Acid ◽  
Magnetic Resonance ◽  
Aluminium Oxide ◽  
Nuclear Magnetic Resonance Data ◽  
Gas Chromatograph ◽  
Tobacco Products ◽  
Magnetic Resonance Data ◽  
Resonance Data

AbstractBased on previous work (7) a method to simultaneously determine vamidothion [I], vamidothion-sulfoxide [II] and vamidothion sulfone [III] in tobacco has been developed. The compounds are extracted with water/acetone/acetic acid from the tobacco, cleansed over an aluminium oxide column and then determined on the gas chromatograph with the specific sulphur detector. Rates of recovery are 70 % - 92 %, the determination level is 0.1 ppm. Mass spectrometry and nuclear magnetic resonance data of vamidothion [I], vamidothion-sulfoxide [ II ] and vamidothion-sulfone [III] are given.

Testing Aluminium Oxide based Ceramics at Irregular Interrupted Cut

2013 ◽  
Vol 10 (2) ◽  
pp. 26-28
Author(s):  
Ladislav Kyncl ◽  
Robert Cep ◽  
Pavel Novacek ◽  
Jiri Schreier
Keyword(s):  
Aluminium Oxide ◽  
Cutting Effect ◽  
Intermittent Cutting

Abstract This article discusses the test removable ceramic plates during machining with interrupted cut. Tests were performed on a lathe, which was clamped preparation which simulated us the interrupted cut. By changing the number plates mounted in a preparation it was a regular or irregular cut. When with four plates it was regular interrupted cut, the remaining three variants were already irregular cut. It was examined whether it will have the irregular intermittent cutting effect on the insert and possibly how it will change life of inserts during irregular interrupted cut.

Sign in / Sign up

Export Citation Format

Share Document