Analysis of crack parameters under pure Mode II loading by modified exponential matrix method

2021 ◽  
Vol 111 ◽  
pp. 102820
Author(s):  
J.M. Nianga ◽  
F. Mejni ◽  
T. Kanit ◽  
J. Li ◽  
A. Imad
Keyword(s):  
Matrix Method ◽  
Mode Ii ◽  
Pure Mode ◽  
Mode Ii Loading ◽  
Exponential Matrix

Microstructural Effects on Fracture Toughness of Polycrystalline Ceramics in Combined Mode I and Mode II Loading

1989 ◽  
Vol 111 (1) ◽  
pp. 174-180 ◽  
Author(s):  
D. Singh ◽  
D. K. Shetty
Keyword(s):  
Fracture Toughness ◽  
Mode I ◽  
Mode Ii ◽  
Mixed Mode Fracture ◽  
Transgranular Fracture ◽  
Pure Mode ◽  
Polycrystalline Alumina ◽  
Polycrystalline Ceramics ◽  
Mode Ii Loading ◽  
Combined Mode

Fracture toughness of polycrystalline alumina and ceria partially stabilized tetragonal zirconia (CeO2-TZP) ceramics were assessed in combined mode I and mode II loading using precracked disk specimens in diametral compression. Stress states ranging from pure mode I, combined mode I and mode II, and pure mode II were obtained by aligning the center crack at specific angles relative to the loading diameter. The resulting mixed-mode fracture toughness envelope showed significant deviation to higher fracture toughness in mode II relative to the predictions of the linear elastic fracture mechanics theory. Critical comparison with corresponding results on soda-lime glass and fracture surface observations showed that crack surface resistance arising from grain interlocking and abrasion were the main sources of the increased fracture toughness in mode II loading of the polycrystalline ceramics. The normalized fracture toughness for pure mode II loading, (KII/KIc), increased with increasing grain size for the CeO2-TZP ceramics. Quantitative fractography confirmed an increased percentage of transgranular fracture of the grains in mode II loading.

Experimental and Theoretical Study of Fracture Paths in Brittle Cracked Materials Subjected to Pure Mode II Loading

2011 ◽  
Vol 70 ◽  
pp. 159-164 ◽  
Author(s):  
M.R.M. Aliha ◽  
Mahdi Rezaei
Keyword(s):  
Crack Growth ◽  
Compressive Loading ◽  
Fracture Initiation ◽  
Mode Ii ◽  
Pure Mode ◽  
Center Crack ◽  
Fracture Parameters ◽  
Growth Method ◽  
Crack Growth Path ◽  
Mode Ii Loading

Crack growth path was investigated experimentally, numerically and theoretically using two test specimens subjected to pure mode II loading. The specimens were (a) the center cracked circular disc (CCCD) specimen subjected to diametral compression often called the Brazilian disc and (b) the diagonally loaded square plate (DLSP) specimen containing inclined center crack and subjected to pin loading. A few CCCD and DLSP specimens made of two brittle materials (i.e. marble rock and PMMA) were tested under pure mode II conditions. It was observed that the fracture initiation directions and the fracture paths for the tested specimens differed significantly and grew in two different trajectories. However, it was shown that the experimentally observed fracture paths for both specimens can be predicted theoretically very well by using the incremental crack growth method. Several finite element analyses were performed to simulate the whole fracture trajectories of the tested CCCD and DLSP specimens. At each increment, the direction of fracture initiation for the tip of growing crack was determined using the fracture parameters (i.e. stress intensity factors and T-stress) based on the modified maximum tangential stress (MMTS) criterion. The main difference in the fracture trajectory was found to be related to the magnitude and sign of the fracture parameters (which depend strongly on the specimen geometry and loading configuration) and also the type of tensile or compressive loading in the CCCD and DLSP samples.

scholarly journals Mixed-Mode Interlaminar Fracture Toughness of Glass and Carbon Fibre Powder Epoxy Composites—For Design of Wind and Tidal Turbine Blades

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2103
Author(s):  
Christophe Floreani ◽  
Colin Robert ◽  
Parvez Alam ◽  
Peter Davies ◽  
Conchúr M. Ó. Brádaigh
Keyword(s):  
Fracture Toughness ◽  
Carbon Fibre ◽  
Composite Structures ◽  
Mixed Mode ◽  
Epoxy Composites ◽  
Mode I ◽  
Mode Ii ◽  
Pure Mode ◽  
Interlaminar Fracture Toughness ◽  
Interlaminar Fracture

Powder epoxy composites have several advantages for the processing of large composite structures, including low exotherm, viscosity and material cost, as well as the ability to carry out separate melting and curing operations. This work studies the mode I and mixed-mode toughness, as well as the in-plane mechanical properties of unidirectional stitched glass and carbon fibre reinforced powder epoxy composites. The interlaminar fracture toughness is studied in pure mode I by performing Double Cantilever Beam tests and at 25% mode II, 50% mode II and 75% mode II by performing Mixed Mode Bending testing according to the ASTM D5528-13 test standard. The tensile and compressive properties are comparable to that of standard epoxy composites but both the mode I and mixed-mode toughness are shown to be significantly higher than that of other epoxy composites, even when comparing to toughened epoxies. The mixed-mode critical strain energy release rate as a function of the delamination mode ratio is also provided. This paper highlights the potential for powder epoxy composites in the manufacturing of structures where there is a risk of delamination.

Sign in / Sign up

Export Citation Format

Share Document