The aerodynamic performance of paragliders

1999 ◽  
Vol 103 (1027) ◽  
pp. 421-428 ◽  
Author(s):  
H. Babinsky
Keyword(s):  
Separation Bubble ◽  
Lift Coefficient ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Two Dimensional ◽  
Trailing Edge ◽  
Wing Section ◽  
Two Factors ◽  
Performance Deterioration ◽  
Edge Separation

Abstract An analysis of paraglider performance has revealed that wing section drag is the most significant contribution to overall drag. Wind tunnel measurements performed on two-dimensional hollow models indicate that intake drag is less significant than previously thought. An experimental investigation into the characteristics of a ‘quasi ’ -two-dimensional flexible model consisting of solid ribs covered with a fabric skin was performed at realistic Reynolds numbers. The main cause of performance deterioration was found to be a significant reduction in section lift coefficient when compared to a similar solid wing section. This is believed to be mainly due to two factors: a large trailing edge separation and the deformation of the wing between ribs. The deformation was measured and it was shown that the deformed shape is less capable of generating high lift coefficients than the design section. It is thought that the extent of the trailing edge separation is increased due to the presence of streamwise grooves caused by the shape deformation of the wing. The shape of the separated region was found to be strongly three-dimensional with the separation point being about half a chord-length further upstream along the ribs. A small separation bubble was also observed immediately behind the lip of the intake, due to the fabric ‘flaring’ open. Based on the observations presented a number of suggestions for improved wings have been made.

Three-Dimensional Vortex Structure in a Leading-Edge Separation Bubble at Moderate Reynolds Numbers

1991 ◽  
Vol 113 (3) ◽  
pp. 405-410 ◽  
Author(s):  
Kyuro Sasaki ◽  
Masaru Kiya
Keyword(s):  
Reynolds Number ◽  
Separation Bubble ◽  
Plate Thickness ◽  
Three Dimensional ◽  
Leading Edge ◽  
Reynolds Numbers ◽  
Vortex Filaments ◽  
Separated Shear Layer ◽  
Hydrogen Bubbles ◽  
Edge Separation

This paper describes the results of a flow visualization study which concerns three-dimensional vortex structures in a leading-edge separation bubble formed along the sides of a blunt flat plate. Dye and hydrogen bubbles were used as tracers. Reynolds number (Re), based on the plate thickness, was varied from 80 to 800. For 80 < Re < 320, the separated shear layer remains laminar up to the reattachment line without significant spanwise distortion of vortex filaments. For 320 < Re < 380, a Λ-shaped deformation of vortex filaments appears shortly downstream of the reattachment and is arranged in-phase in the downstream direction. For Re > 380, hairpin-like structures are formed and arranged in a staggered manner. The longitudinal and spanwise distances of the vortex arrangement are presented as functions of the Reynolds number.

Experiments With Three-Dimensional Passive Flow Control Devices on Low-Pressure Turbine Airfoils

2004 ◽  
Vol 128 (2) ◽  
pp. 251-260 ◽  
Author(s):  
Douglas G. Bohl ◽  
Ralph J. Volino
Keyword(s):  
Reynolds Number ◽  
Flow Control ◽  
Separation Bubble ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Low Pressure ◽  
Trailing Edge ◽  
Low Pressure Turbine ◽  
Wide Range ◽  
Turbine Airfoils

The effectiveness of three-dimensional passive devices for flow control on low pressure turbine airfoils was investigated experimentally. A row of small cylinders was placed at the pressure minimum on the suction side of a typical airfoil. Cases with Reynolds numbers ranging from 25,000 to 300,000 (based on suction surface length and exit velocity) were considered under low freestream turbulence conditions. Streamwise pressure profiles and velocity profiles near the trailing edge were documented. Without flow control a separation bubble was present, and at the lower Reynolds numbers the bubble did not close. Cylinders with two different heights and a wide range of spanwise spacings were considered. Reattachment moved upstream as the cylinder height was increased or the spacing was decreased. If the spanwise spacing was sufficiently small, the flow at the trailing edge was essentially uniform across the span. The cylinder size and spacing could be optimized to minimize losses at a given Reynolds number, but cylinders optimized for low Reynolds number conditions caused increased losses at high Reynolds numbers. The effectiveness of two-dimensional bars had been studied previously under the same flow conditions. The cylinders were not as effective for maintaining low losses over a range of Reynolds numbers as the bars.

Experiments With Three Dimensional Passive Flow Control Devices on Low-Pressure Turbine Airfoils

2005 ◽  
Author(s):  
Douglas G. Bohl ◽  
Ralph J. Volino
Keyword(s):  
Reynolds Number ◽  
Flow Control ◽  
Separation Bubble ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Low Pressure ◽  
Trailing Edge ◽  
Low Pressure Turbine ◽  
Wide Range ◽  
Turbine Airfoils

The effectiveness of three dimensional passive devices for flow control on low pressure turbine airfoils was investigated experimentally. A row of small cylinders was placed at the pressure minimum on the suction side of a typical airfoil. Cases with Reynolds numbers ranging from 25,000 to 300,000 (based on suction surface length and exit velocity) were considered under low freestream turbulence conditions. Streamwise pressure profiles and velocity profiles near the trailing edge were documented. Without flow control a separation bubble was present, and at the lower Reynolds numbers the bubble did not close. Cylinders with two different heights and a wide range of spanwise spacings were considered. Reattachment moved upstream as the cylinder height was increased or the spacing was decreased. If the spanwise spacing was sufficiently small, the flow at the trailing edge was essentially uniform across the span. The cylinder size and spacing could be optimized to minimize losses at a given Reynolds number, but cylinders optimized for low Reynolds number conditions caused increased losses at high Reynolds numbers. The effectiveness of two-dimensional bars had been studied previously under the same flow conditions. The cylinders were not as effective for maintaining low losses over a range of Reynolds numbers as the bars.

scholarly journals Three-dimensional instability in flow over a backward-facing step

2002 ◽  
Vol 473 ◽  
pp. 167-190 ◽  
Author(s):  
DWIGHT BARKLEY ◽  
M. GABRIELA M. GOMES ◽  
RONALD D. HENDERSON
Keyword(s):  
Reynolds Number ◽  
Separation Bubble ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Expansion Ratio ◽  
Linear Instability ◽  
Two Dimensional ◽  
Backward Facing Step ◽  
Computational Stability ◽  
Two Dimensional Flow

Results are reported from a three-dimensional computational stability analysis of flow over a backward-facing step with an expansion ratio (outlet to inlet height) of 2 at Reynolds numbers between 450 and 1050. The analysis shows that the first absolute linear instability of the steady two-dimensional flow is a steady three-dimensional bifurcation at a critical Reynolds number of 748. The critical eigenmode is localized to the primary separation bubble and has a flat roll structure with a spanwise wavelength of 6.9 step heights. The system is further shown to be absolutely stable to two-dimensional perturbations up to a Reynolds number of 1500. Stability spectra and visualizations of the global modes of the system are presented for representative Reynolds numbers.

Three-Dimensional and Rotational Aerodynamics on the NREL Phase VI Wind Turbine Blade

2008 ◽  
Vol 130 (3) ◽  
Author(s):  
Alvaro Gonzalez ◽  
Xabier Munduate
Keyword(s):  
Wind Turbine ◽  
Turbine Blade ◽  
Three Dimensional ◽  
Separated Flow ◽  
Leading Edge ◽  
Wind Turbine Blade ◽  
Trailing Edge ◽  
Rotating Blade ◽  
Nrel Phase Vi ◽  
Edge Separation

This work undertakes an aerodynamic analysis over the parked and the rotating NREL Phase VI wind turbine blade. The experimental sequences from NASA Ames wind tunnel selected for this study respond to the parked blade and the rotating configuration, both for the upwind, two-bladed wind turbine operating at nonyawed conditions. The objective is to bring some light into the nature of the flow field and especially the type of stall behavior observed when 2D aerofoil steady measurements are compared to the parked blade and the latter to the rotating one. From averaged pressure coefficients together with their standard deviation values, trailing and leading edge separated flow regions have been found, with the limitations of the repeatability of the flow encountered on the blade. Results for the parked blade show the progressive delay from tip to root of the trailing edge separation process, with respect to the 2D profile, and also reveal a local region of leading edge separated flow or bubble at the inner, 30% and 47% of the blade. For the rotating blade, results at inboard 30% and 47% stations show a dramatic suppression of the trailing edge separation, and the development of a leading edge separation structure connected with the extra lift.

Bifurcation Characteristics of Flows in Rectangular Sudden Expansion Channels

2005 ◽  
Author(s):  
Francine Battaglia ◽  
George Papadopoulos
Keyword(s):  
Reynolds Number ◽  
Laminar Flow ◽  
Critical Reynolds Number ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Expansion Ratio ◽  
Sudden Expansion ◽  
Two Dimensional ◽  
Effective Expansion ◽  
Three Dimensional Simulations

The effect of three-dimensionality on low Reynolds number flows past a symmetric sudden expansion in a channel was investigated. The geometric expansion ratio of in the current study was 2:1 and the aspect ratio was 6:1. Both experimental velocity measurements and two- and three-dimensional simulations for the flow along the centerplane of the rectangular duct are presented for Reynolds numbers in the range of 150 to 600. Comparison of the two-dimensional simulations with the experiments revealed that the simulations fail to capture completely the total expansion effect on the flow, which couples both geometric and hydrodynamic effects. To properly do so requires the definition of an effective expansion ratio, which is the ratio of the downstream and upstream hydraulic diameters and is therefore a function of both the expansion and aspect ratios. When the two-dimensional geometry was consistent with the effective expansion ratio, the new results agreed well with the three-dimensional simulations and the experiments. Furthermore, in the range of Reynolds numbers investigated, the laminar flow through the expansion underwent a symmetry-breaking bifurcation. The critical Reynolds number evaluated from the experiments and the simulations was compared to other values reported in the literature. Overall, side-wall proximity was found to enhance flow stability, helping to sustain laminar flow symmetry to higher Reynolds numbers in comparison to nominally two-dimensional double-expansion geometries. Lastly, and most importantly, when the logarithm of the critical Reynolds number from all these studies was plotted against the reciprocal of the effective expansion ratio, a linear trend emerged that uniquely captured the bifurcation dynamics of all symmetric double-sided planar expansions.

The aerodynamic theory of sails. I. Two-dimensional sails

1961 ◽  
Vol 261 (1306) ◽  
pp. 402-422 ◽  
Keyword(s):  
Lift Coefficient ◽  
Linear Equations ◽  
Three Dimensional ◽  
Angle Of Incidence ◽  
Two Dimensional ◽  
Inviscid Incompressible Fluid ◽  
Two Dimensional Flow ◽  
Linearized Theory ◽  
High Degree ◽  
Additional Equation

This paper deals with the preliminaries essential for any theoretical investigation of three-dimensional sails—namely, with the two-dimensional flow of inviscid incompressible fluid past an infinitely-long flexible inelastic membrane. If the distance between the luff and the leach of the two-dimensional sail is c , and if the length of the material of the sail between luff and leach is ( c + l ), then the problem is to determine the flow when the angle of incidence α between the chord of the sail and the wind, and the ratio l / c are both prescribed; especially, we need to know the shape of, the loading on, and the tension in, the sail. The aerodynamic theory follows the lines of the conventional linearized theory of rigid aerofoils; but in the case of a sail, there is an additional equation to be satisfied which ex­presses the static equilibrium of each element of the sail. The resulting fundamental integral equation—the sail equation—is consequently quite different from those of aerofoil theory, and it is not susceptible to established methods of solution. The most striking result is the theoretical possibility of more than one shape of sail for given values of α and l / c ; but there appears to be no difficulty in choosing the shape which occurs in reality. The simplest result for these realistic shapes is that the lift coefficient of a sail exceeds that of a rigid flat plate (for which l / c = 0) by an amount approximately equal to 0.636 ( l / c ) ½ . It seems very doubtful whether analytical solutions of the sail equation will be found, but a method is developed in this paper which comes to the next best thing; namely, an explicit expression, as a matrix quotient, which gives numerical values to a high degree of accuracy at so many chord-wise points. The method should have wide application to other types of linear equations.

Cellular flow in a partially filled rotating drum: regular and chaotic advection

2017 ◽  
Vol 825 ◽  
pp. 631-650 ◽  
Author(s):  
Francesco Romanò ◽  
Arash Hajisharifi ◽  
Hendrik C. Kuhlmann
Keyword(s):  
Three Dimensional ◽  
Reynolds Numbers ◽  
Chaotic Advection ◽  
Two Dimensional ◽  
Rotating Drum ◽  
Three Dimensional Flow ◽  
Dimensional Flow ◽  
Heteroclinic Connection ◽  
Two Dimensional Flow ◽  
Chaotic Streamlines

The topology of the incompressible steady three-dimensional flow in a partially filled cylindrical rotating drum, infinitely extended along its axis, is investigated numerically for a ratio of pool depth to radius of 0.2. In the limit of vanishing Froude and capillary numbers, the liquid–gas interface remains flat and the two-dimensional flow becomes unstable to steady three-dimensional convection cells. The Lagrangian transport in the cellular flow is organised by periodic spiralling-in and spiralling-out saddle foci, and by saddle limit cycles. Chaotic advection is caused by a breakup of a degenerate heteroclinic connection between the two saddle foci when the flow becomes three-dimensional. On increasing the Reynolds number, chaotic streamlines invade the cells from the cell boundary and from the interior along the broken heteroclinic connection. This trend is made evident by computing the Kolmogorov–Arnold–Moser tori for five supercritical Reynolds numbers.

The Three-Dimensional Turbulent Boundary Layer on an Infinite Yawed Wing

1971 ◽  
Vol 22 (4) ◽  
pp. 346-362 ◽  
Author(s):  
J. F. Nash ◽  
R. R. Tseng
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Turbulent Boundary Layer ◽  
Lift Coefficient ◽  
Three Dimensional ◽  
Numerical Representation ◽  
Two Dimensional ◽  
Incompressible Turbulent Boundary Layer ◽  
Displacement Thickness ◽  
Attachment Line

SummaryThis paper presents the results of some calculations of the incompressible turbulent boundary layer on an infinite yawed wing. A discussion is made of the effects of increasing lift coefficient, and increasing Reynolds number, on the displacement thickness, and on the magnitude and direction of the skin friction. The effects of the state of the boundary layer (laminar or turbulent) along the attachment line are also considered.A study is made to determine whether the behaviour of the boundary layer can adequately be predicted by a two-dimensional calculation. It is concluded that there is no simple way to do this (as is provided, in the laminar case, by the principle of independence). However, with some modification, a two-dimensional calculation can be made to give an acceptable numerical representation of the chordwise components of the flow.

Sign in / Sign up

Export Citation Format

Share Document