Pressure-gradient-dependent logarithmic laws in sink flow turbulent boundary layers

2008 ◽  
Vol 615 ◽  
pp. 445-475 ◽  
Author(s):  
SHIVSAI AJIT DIXIT ◽  
O. N. RAMESH
Keyword(s):  
Differential Equations ◽  
Pressure Gradient ◽  
Boundary Layers ◽  
Turbulent Boundary Layers ◽  
Pressure Gradients ◽  
Mean Flow ◽  
Mean Velocity ◽  
Wide Range ◽  
Gradient Parameter ◽  
The Mean

Experiments were done on sink flow turbulent boundary layers over a wide range of streamwise pressure gradients in order to investigate the effects on the mean velocity profiles. Measurements revealed the existence of non-universal logarithmic laws, in both inner and defect coordinates, even when the mean velocity descriptions departed strongly from the universal logarithmic law (with universal values of the Kármán constant and the inner law intercept). Systematic dependences of slope and intercepts for inner and outer logarithmic laws on the strength of the pressure gradient were observed. A theory based on the method of matched asymptotic expansions was developed in order to explain the experimentally observed variations of log-law constants with the non-dimensional pressure gradient parameter (Δp=(ν/ρU3τ)dp/dx). Towards this end, the system of partial differential equations governing the mean flow was reduced to inner and outer ordinary differential equations in self-preserving form, valid for sink flow conditions. Asymptotic matching of the inner and outer mean velocity expansions, extended to higher orders, clearly revealed the dependence of slope and intercepts on pressure gradient in the logarithmic laws.

Scaling of adverse-pressure-gradient turbulent boundary layers

1992 ◽  
Vol 238 ◽  
pp. 699-722 ◽  
Author(s):  
P. A. Durbin ◽  
S. E. Belcher
Keyword(s):  
Boundary Layer ◽  
Pressure Gradient ◽  
Boundary Layers ◽  
Turbulent Boundary Layers ◽  
Wall Layer ◽  
Small Range ◽  
Surface Shear Stress ◽  
Pressure Gradients ◽  
Mean Flow ◽  
The Mean

An asymptotic analysis is developed for turbulent boundary layers in strong adverse pressure gradients. It is found that the boundary layer divides into three distinguishable regions: these are the wall layer, the wake layer and a transition layer. This structure has two key differences from the zero-pressure-gradient boundary layer: the wall layer is not exponentially thinner than the wake; and the wake has a large velocity deficit, and cannot be linearized. The mean velocity profile has a y½ behaviour in the overlap layer between the wall and transition regions.The analysis is done in the context of eddy viscosity closure modelling. It is found that k-ε-type models are suitable to the wall region, and have a power-law solution in the y½ layer. The outer-region scaling precludes the usual ε-equation. The Clauser, constant-viscosity model is used in that region. An asymptotic expansion of the mean flow and matching between the three regions is carried out in order to determine the relation between skin friction and pressure gradient. Numerical calculations are done for self-similar flow. It is found that the surface shear stress is a double-valued function of the pressure gradient in a small range of pressure gradients.

Re-Developing Turbulent Boundary Layers Behind Yawed Separation Bubbles

1972 ◽  
Vol 23 (3) ◽  
pp. 211-228 ◽  
Author(s):  
H P Horton
Keyword(s):  
Energy Dissipation ◽  
Pressure Gradient ◽  
Boundary Layers ◽  
Three Dimensional ◽  
Turbulent Boundary Layers ◽  
Two Dimensional ◽  
Mean Flow ◽  
Separation Bubbles ◽  
Gradient Parameter ◽  
The Mean

SummaryMeasurements are presented of the mean flow properties of some three-dimensional turbulent boundary layers re-developing after reattachment behind short separation bubbles yawed at 26.5° to the main stream. For these measurements, Rθ11varied from about 550 to 1450. It was found that, where the pressure gradient parameter (ν/ρu3τ1)∂p/∂s was not greater than about 0.05, the flow in the local external streamline direction conformed well with empirical laws for fully-attached two-dimensional layers with regard to the mean velocity profiles, shape parameter relationships and skin friction laws, giving support to the usual assumption that these two-dimensional relationships may be applied to the streamwise flow in three-dimensional layers, subject to the limitation on the pressure gradient parameter. The cross-flow profiles, on the other hand, were not generally fitted well by the often-used representations of Mager and Johnston. The variations of the kinetic energy dissipation coefficient and the entrainment rate were deduced for one of the layers, both quantities being found to be higher than those predicted by empirical relationships for conventionally-developing two-dimensional layers. However, the energy dissipation is in fair agreement with that in a similarly re-developing two-dimensional flow.

scholarly journals On the streamwise evolution of turbulent boundary layers in arbitrary pressure gradients

2002 ◽  
Vol 461 ◽  
pp. 61-91 ◽  
Author(s):  
A. E. PERRY ◽  
IVAN MARUSIC ◽  
M. B. JONES
Keyword(s):  
Boundary Layers ◽  
Scaling Laws ◽  
Power Spectra ◽  
Adverse Pressure Gradient ◽  
Turbulent Boundary Layers ◽  
Stream Velocity ◽  
Mean Flow ◽  
Mean Velocity ◽  
Law Of The Wall ◽  
The Mean

A new approach to the classic closure problem for turbulent boundary layers is presented. This involves, first, using the well-known mean-flow scaling laws such as the log law of the wall and the law of the wake of Coles (1956) together with the mean continuity and the mean momentum differential and integral equations. The important parameters governing the flow in the general non-equilibrium case are identified and are used for establishing a framework for closure. Initially closure is achieved here empirically and the potential for achieving closure in the future using the wall-wake attached eddy model of Perry & Marusic (1995) is outlined. Comparisons are made with experiments covering adverse-pressure-gradient flows in relaxing and developing states and flows approaching equilibrium sink flow. Mean velocity profiles, total shear stress and Reynolds stress profiles can be computed for different streamwise stations, given an initial upstream mean velocity profile and the streamwise variation of free-stream velocity. The attached eddy model of Perry & Marusic (1995) can then be utilized, with some refinement, to compute the remaining unknown quantities such as Reynolds normal stresses and associated spectra and cross-power spectra in the fully turbulent part of the flow.

Scaling of Favorable Pressure Gradient Turbulent Boundary Layers With Eventual Relaminarization

2005 ◽  
Author(s):  
Rau´l Bayoa´n Cal ◽  
Xia Wang ◽  
Luciano Castillo
Keyword(s):  
Boundary Layer ◽  
Pressure Gradient ◽  
Boundary Layers ◽  
Reynolds Shear Stress ◽  
Velocity Profiles ◽  
Turbulent Boundary Layers ◽  
Reynolds Stresses ◽  
Mean Velocity ◽  
Favorable Pressure Gradient ◽  
The Mean

Applying similarity analysis to the RANS equations of motion for a pressure gradient turbulent boundary layer, Castillo and George [1] obtained the scalings for the mean deficit velocity and the Reynolds stresses. Following this analysis, Castillo and George studied favorable pressure gradient (FPG) turbulent boundary layers. They were able to obtain a single curve for FPG flows when scaling the mean deficit velocity profiles. In this study, FPG turbulent boundary layers are analyzed as well as relaminarized boundary layers subjected to an even stronger FPG. It is found that the mean deficit velocity profiles diminish when scaled using the Castillo and George [1] scaling, U∞, and the Zagarola and Smits [2] scaling, U∞δ*/δ. In addition, Reynolds stress data has been analyzed and it is found that the relaminarized boundary layer data decreases drastically in all components of the Reynolds stresses. Furthermore, it will be shown that the shape of the profile for the wall-normal and Reynolds shear stress components change drastically given the relaminarized state. Therefore, the mean velocity deficit profiles as well as Reynolds stresses are found to be necessary in order to understand not only FPG flows, but also relaminarized boundary layers.

scholarly journals Evolution and structure of sink-flow turbulent boundary layers

2001 ◽  
Vol 428 ◽  
pp. 1-27 ◽  
Author(s):  
M. B. JONES ◽  
IVAN MARUSIC ◽  
A. E. PERRY
Keyword(s):  
Boundary Layers ◽  
Velocity Profiles ◽  
Turbulent Boundary Layers ◽  
Reynolds Stresses ◽  
Mean Flow ◽  
Mean Velocity ◽  
Flow Measurements ◽  
Law Of The Wall ◽  
The Mean ◽  
Logarithmic Law

An experimental and theoretical investigation of turbulent boundary layers developing in a sink-flow pressure gradient was undertaken. Three flow cases were studied, corresponding to different acceleration strengths. Mean-flow measurements were taken for all three cases, while Reynolds stresses and spectra measurements were made for two of the flow cases. In this study attention was focused on the evolution of the layers to an equilibrium turbulent state. All the layers were found to attain a state very close to precise equilibrium. This gave equilibrium sink flow data at higher Reynolds numbers than in previous experiments. The mean velocity profiles were found to collapse onto the conventional logarithmic law of the wall. However, for profiles measured with the Pitot tube, a slight ‘kick-up’ from the logarithmic law was observed near the buffer region, whereas the mean velocity profiles measured with a normal hot wire did not exhibit this deviation from the logarithmic law. As the layers approached equilibrium, the mean velocity profiles were found to approach the pure wall profile and for the highest level of acceleration Π was very close to zero, where Π is the Coles wake factor. This supports the proposition of Coles (1957), that the equilibrium sink flow corresponds to pure wall flow. Particular interest was also given to the evolutionary stages of the boundary layers, in order to test and further develop the closure hypothesis of Perry, Marusic & Li (1994). Improved quantitative agreement with the experimental results was found after slight modification of their original closure equation.

Direct numerical simulation of hypersonic turbulent boundary layers. Part 4. Effect of high enthalpy

2011 ◽  
Vol 684 ◽  
pp. 25-59 ◽  
Author(s):  
L. Duan ◽  
M. P. Martín
Keyword(s):  
Boundary Layers ◽  
Transport Model ◽  
Turbulent Boundary Layers ◽  
Turbulence Structure ◽  
Mean Velocity ◽  
Reynolds Analogy ◽  
High Enthalpy ◽  
Turbulent Schmidt Number ◽  
Wide Range ◽  
The Mean

AbstractIn this paper we present direct numerical simulations (DNS) of hypersonic turbulent boundary layers to study high-enthalpy effects. We study high- and low-enthalpy conditions, which are representative of those in hypersonic flight and ground-based facilities, respectively. We find that high-enthalpy boundary layers closely resemble those at low enthalpy. Many of the scaling relations for low-enthalpy flows, such as van-Driest transformation for the mean velocity, Morkovin’s scaling and the modified strong Reynolds analogy hold or can be generalized for high-enthalpy flows by removing the calorically perfect-gas assumption. We propose a generalized form of the modified Crocco relation, which relates the mean temperature and mean velocity across a wide range of conditions, including non-adiabatic cold walls and real gas effects. The DNS data predict Reynolds analogy factors in the range of those found in experimental data at low-enthalpy conditions. The gradient transport model approximately holds with turbulent Prandtl number and turbulent Schmidt number of order unity. Direct compressibility effects remain small and insignificant for all enthalpy cases. High-enthalpy effects have no sizable influence on turbulent kinetic energy (TKE) budgets or on the turbulence structure.

Transpired Turbulent Boundary Layers Subject to Forced Convection and External Pressure Gradients

2005 ◽  
Vol 127 (2) ◽  
pp. 194-198 ◽  
Author(s):  
Rau´l Bayoa´n Cal, ◽  
Xia Wang, ◽  
Luciano Castillo
Keyword(s):  
Pressure Gradient ◽  
Forced Convection ◽  
Boundary Layers ◽  
Turbulent Boundary Layers ◽  
External Pressure ◽  
Turbulent Pipe Flow ◽  
Mean Flow ◽  
Outer Flow ◽  
The Mean ◽  
Blowing Parameter

The problem of forced convection transpired turbulent boundary layers with external pressure gradient has been studied by using different scalings proposed by various researchers. Three major results were obtained: First, for adverse pressure gradient boundary layers with suction, the mean deficit profiles collapse with the free stream velocity, U∞, but into different curves depending on the strength of the blowing parameter and the upstream conditions. Second, the dependencies on the blowing parameter, the Reynolds number, and the strength of pressure gradient are removed from the outer flow when the mean deficit profiles are normalized by the Zagarola/Smits [Zagarola, M. V., and Smits, A. J., 1998, “Mean-Flow Scaling of Turbulent Pipe Flow,” J. Fluid Mech., 373, 33–79] scaling, U∞δ*/δ. Third, the temperature profiles collapse into a single curve using the new inner and outer scalings proposed by Wang and Castillo [Wang, X., and Castillo, L., 2003, “Asymptotic Solutions in Forced Convection Turbulent Boundary Layers,” J. Turbulence, 4(006)], which produce the true asymptotic profiles even at finite Pe´clet number.

The mean velocity profile of turbulent boundary layers with system rotation

2000 ◽  
Vol 408 ◽  
pp. 323-345 ◽  
Author(s):  
T. B. NICKELS ◽  
P. N. JOUBERT
Keyword(s):  
Velocity Profile ◽  
Boundary Layers ◽  
Turbulent Boundary Layers ◽  
Secondary Flows ◽  
Pressure Gradients ◽  
Mean Velocity ◽  
System Rotation ◽  
Linear Correction ◽  
The Mean ◽  
The University

This paper examines changes in the mean velocity profiles of turbulent boundary layers subjected to system rotation. Analysis of the data from several studies conducted in the large rotating wind tunnel at the University of Melbourne shows the existence of a universal linear correction to the velocity profile in the logarithmic region. The appropriate parameters relevant to rotation are derived and correlations are found between the parameters. Flows with adverse pressure gradients, zero pressure gradients and secondary flows are examined and all appear to exhibit the universal linear correction, suggesting that it is robust.

History effects and near equilibrium in adverse-pressure-gradient turbulent boundary layers

2017 ◽  
Vol 820 ◽  
pp. 667-692 ◽  
Author(s):  
A. Bobke ◽  
R. Vinuesa ◽  
R. Örlü ◽  
P. Schlatter
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Pressure Gradient ◽  
Boundary Layers ◽  
Adverse Pressure Gradient ◽  
Turbulent Boundary Layers ◽  
Mean Velocity ◽  
History Effects ◽  
Displacement Thickness ◽  
Gradient Parameter

Turbulent boundary layers under adverse pressure gradients are studied using well-resolved large-eddy simulations (LES) with the goal of assessing the influence of the streamwise pressure-gradient development. Near-equilibrium boundary layers were characterized through the Clauser pressure-gradient parameter $\unicode[STIX]{x1D6FD}$. In order to fulfil the near-equilibrium conditions, the free stream velocity was prescribed such that it followed a power-law distribution. The turbulence statistics pertaining to cases with a constant value of $\unicode[STIX]{x1D6FD}$ (extending up to approximately 40 boundary-layer thicknesses) were compared with cases with non-constant $\unicode[STIX]{x1D6FD}$ distributions at matched values of $\unicode[STIX]{x1D6FD}$ and friction Reynolds number $Re_{\unicode[STIX]{x1D70F}}$. An additional case at matched Reynolds number based on displacement thickness $Re_{\unicode[STIX]{x1D6FF}^{\ast }}$ was also considered. It was noticed that non-constant $\unicode[STIX]{x1D6FD}$ cases appear to approach the conditions of equivalent constant $\unicode[STIX]{x1D6FD}$ cases after long streamwise distances (approximately 7 boundary-layer thicknesses). The relevance of the constant $\unicode[STIX]{x1D6FD}$ cases lies in the fact that they define a ‘canonical’ state of the boundary layer, uniquely characterized by $\unicode[STIX]{x1D6FD}$ and $Re$. The investigations on the flat plate were extended to the flow around a wing section overlapping in terms of $\unicode[STIX]{x1D6FD}$ and $Re$. Comparisons with the flat-plate cases at matched values of $\unicode[STIX]{x1D6FD}$ and $Re$ revealed that the different development history of the turbulent boundary layer on the wing section leads to a less pronounced wake in the mean velocity as well as a weaker second peak in the Reynolds stresses. This is due to the weaker accumulated effect of the $\unicode[STIX]{x1D6FD}$ history. Furthermore, a scaling law suggested by Kitsios et al. (Intl J. Heat Fluid Flow, vol. 61, 2016, pp. 129–136), proposing the edge velocity and the displacement thickness as scaling parameters, was tested on two constant-pressure-gradient parameter cases. The mean velocity and Reynolds-stress profiles were found to be dependent on the downstream development. The present work is the first step towards assessing history effects in adverse-pressure-gradient turbulent boundary layers and highlights the fact that the values of the Clauser pressure-gradient parameter and the Reynolds number are not sufficient to characterize the state of the boundary layer.

Structures in turbulent boundary layers subjected to adverse pressure gradients

2009 ◽  
Vol 639 ◽  
pp. 101-131 ◽  
Author(s):  
JOUNG-HO LEE ◽  
HYUNG JIN SUNG
Keyword(s):  
Boundary Layer ◽  
Pressure Gradient ◽  
Boundary Layers ◽  
Adverse Pressure Gradient ◽  
Turbulent Boundary Layers ◽  
Stochastic Estimation ◽  
Pressure Gradients ◽  
Linear Stochastic Estimation ◽  
Mean Width ◽  
The Mean

The effects of adverse pressure gradients on turbulent structures were investigated by carrying out direct numerical simulations of turbulent boundary layers subjected to adverse and zero pressure gradients. The equilibrium adverse pressure gradient flows were established by using a power law free-stream distribution U∞ ~ xm. Two-point correlations of velocity fluctuations were used to show that the spanwise spacing between near-wall streaks is affected significantly by a strong adverse pressure gradient. Low-momentum regions are dominant in the middle of the boundary layer as well as in the log layer. Linear stochastic estimation was used to provide evidence for the presence of low-momentum regions and to determine their statistical properties. The mean width of such large-scale structures is closely associated with the size of the hairpin-like vortices in the outer layer. The conditionally averaged flow fields around events producing Reynolds stress show that hairpin-like vortices are the structures associated with the production of outer turbulence. The shapes of the vortices beyond the log layer were found to be similar when their length scales were normalized according to the boundary layer thickness. Estimates of the conditionally averaged velocity fields associated with the spanwise vortical motion were obtained by using linear stochastic estimation. These results confirm that the outer region of the adverse pressure gradient boundary layer is populated with streamwise-aligned vortex organizations, which are similar to those of the vortex packet model proposed by Adrian, Meinhart & Tomkins (J. Fluid Mech., vol. 422, 2000, pp. 1–54). The adverse pressure gradient augments the inclination angles of the packets and the mean streamwise spacing of the vortex heads in the packets.

Sign in / Sign up

Export Citation Format

Share Document