Green and Nondestructive Method for Constructing Multiscale Carbon Fiber Reinforcement via Encapsulating Chitosan and Grafting Carbon Nanotubes

2021 ◽  
Author(s):  
Cheng Zhang ◽  
Xueqin Zhang ◽  
Yinfu Luo ◽  
Mei Liang ◽  
Huawei Zou
Keyword(s):  
Carbon Nanotubes ◽  
Carbon Fiber ◽  
Fiber Reinforcement ◽  
Nondestructive Method ◽  
Carbon Fiber Reinforcement

Structural Behavior of Reinforced Concrete Beams Strengthened with Carbon Fiber Reinforcement Polymer Plate

2013 ◽  
Vol 302 ◽  
pp. 338-342
Author(s):  
Soo Yeon Seo
Keyword(s):  
Carbon Fiber ◽  
Fiber Reinforcement ◽  
Reinforced Concrete Beams ◽  
Structural Behavior ◽  
Rc Beam ◽  
Near Surface ◽  
Cfrp Plate ◽  
Carbon Fiber Reinforcement ◽  
Externally Bonded ◽  
Near Surface Mounted

This paper presents the study to find retrofit effect in case of Near-Surface-Mounted Retrofit (NSMR) using Carbon Fiber Reinforcement Polymer (CFRP) plate targeting reinforcement concrete (RC) beam by comparing the previous Externally Bonded Retrofit (EBR) method through experimental analytical works. Three RC beam specimens were made and two of them were retrofitted with CFRP plate by using EBR and NSMR. Also Finite Element (FE) analysis was performed in order to simulate the structural behavior of the beams by considering the bond properties between concrete and CFRP. From the study, it was found that the beam retrofitted with EBR hada reduction of bond capacity in the joint while the beam retrofitted with NSMR had perfect bond capacity.

scholarly journals Dynamic Flexural Modulus and Low-Velocity Impact Response of Supercomposite<sup>TM</sup> Laminates with Vertical Z-Axis Milled Carbon Fiber Reinforcement

2021 ◽  
Vol 12 (04) ◽  
pp. 152-170
Author(s):  
Suman Babu Ukyam ◽  
Raju P. Mantena ◽  
Damian L. Stoddard ◽  
Arunachalam M. Rajendran ◽  
Robert D. Moser
Keyword(s):  
Carbon Fiber ◽  
Flexural Modulus ◽  
Fiber Reinforcement ◽  
Impact Response ◽  
Low Velocity Impact ◽  
Low Velocity ◽  
Velocity Impact ◽  
Carbon Fiber Reinforcement

Two-component adhesive based on aqueous emulsion of ED-20 resin for carbon-fiber reinforcement of bearing concrete structures

2013 ◽  
Vol 86 (7) ◽  
pp. 1099-1107
Author(s):  
E. V. Shinkareva ◽  
P. I. Statkevich ◽  
V. D. Koshevar ◽  
N. L. Budeiko ◽  
S. N. Leonovich
Keyword(s):  
Carbon Fiber ◽  
Concrete Structures ◽  
Fiber Reinforcement ◽  
Aqueous Emulsion ◽  
Carbon Fiber Reinforcement ◽  
Two Component

Carbon Fiber Reinforced Shape Memory Nanocomposites Incorporated With Highly Conductive Carbon Nanopaper for Electro Actuation

2013 ◽  
Author(s):  
Fei Liang ◽  
Jihua Gou ◽  
He Shen ◽  
Yunjun Xu ◽  
Bob Mabbott
Keyword(s):  
Carbon Fiber ◽  
Shape Memory ◽  
Smart Materials ◽  
Shape Memory Polymer ◽  
Flexural Modulus ◽  
Fiber Reinforcement ◽  
High Strength ◽  
Mechanical Analysis ◽  
Carbon Fiber Reinforcement ◽  
Continuous Carbon Fiber

Shape memory polymers (SMPs) are one of the most popular smart materials due to light weight and high elastic deformation capability. In this study, highly conductive carbon nanofibers paper (CNFP) was coated on the surface of SMP as a conductive layer for electro actuation of SMP. To overcome the drawback of low modulus and low strength of shape memory polymer (SMP), continuous carbon fiber reinforcement was also incorporated with SMP by autoclave processing. The dynamic mechanical analysis (DMA) result showed over 600% increase of storage modulus of SMP by introducing carbon fiber reinforcement. Also, the shape recovery time of SMP has been reduced over 150%, while the recovery ratio of SMP has been improved to 99% by incorporating with carbon fiber reinforcement. Additionally, the mechanical property degradation of SMP composites has been investigated after different electro actuation cycles. After 50 actuation cycles, the decrease of flexural modulus of SMP composites is negligible (< 2%), and the ultimate flexural strength of SMP composites only decreased 25%. The SMP composite shows high strength and modulus, and good durability.

Development of Virtual Process Simulation and Validation for a Carbon Fiber Reinforcement Panel

2020 ◽  
Author(s):  
SELINA ZHAO ◽  
WILLIAM R. RODGERS ARNAUD DEREIMS ◽  
ADAM BURLEY ◽  
VENKAT AITHARAJU
Keyword(s):  
Carbon Fiber ◽  
Process Simulation ◽  
Fiber Reinforcement ◽  
Carbon Fiber Reinforcement ◽  
Simulation And Validation ◽  
Virtual Process

Additively Manufactured Roof Frame Segment with Local Carbon Fiber Reinforcement

2019 ◽  
Vol 12 (4) ◽  
pp. 52-55
Author(s):  
Wojciech Brymerski ◽  
Jan-Philipp Fuhr ◽  
Farbod Nezami
Keyword(s):  
Carbon Fiber ◽  
Fiber Reinforcement ◽  
Carbon Fiber Reinforcement

411 Carbon Fiber Reinforcement for Resin Products by 3D Printer

2015 ◽  
Vol 2015.51 (0) ◽  
pp. _411-1_-_411-2_
Author(s):  
Yuki OIKAWA ◽  
Yuma MIKUNI ◽  
Yuma ENDO ◽  
Tetsuya OIZUMI ◽  
Takatoshi SUENAGA
Keyword(s):  
Carbon Fiber ◽  
Fiber Reinforcement ◽  
3D Printer ◽  
Carbon Fiber Reinforcement

Realization of the properties of the carbon fiber reinforcement in a composite

1981 ◽  
Vol 16 (6) ◽  
pp. 633-636
Author(s):  
Yu. G. Korabel'nikov ◽  
V. M. Bondarenko ◽  
A. N. Shiryaev ◽  
A. V. Zakharov ◽  
M. T. Azarova ◽  
...  
Keyword(s):  
Carbon Fiber ◽  
Fiber Reinforcement ◽  
Carbon Fiber Reinforcement

scholarly journals Carbon Nanotube- and Carbon Fiber-Reinforcement of Ethylene-Octene Copolymer Membranes for Gas and Vapor Separation

Membranes ◽  
2014 ◽  
Vol 4 (1) ◽  
pp. 20-39 ◽  
Author(s):  
Zuzana Sedláková ◽  
Gabriele Clarizia ◽  
Paola Bernardo ◽  
Johannes Jansen ◽  
Petr Slobodian ◽  
...  
Keyword(s):  
Carbon Nanotube ◽  
Carbon Fiber ◽  
Fiber Reinforcement ◽  
Carbon Fiber Reinforcement ◽  
Ethylene Octene Copolymer
Sign in / Sign up

Export Citation Format

Share Document