Freeform fabrication

2022 ◽  
Author(s):  
Nina Meinzer
Keyword(s):  
Freeform Fabrication

Solid Freeform Fabrication Proceedings

2001 ◽  
Author(s):  
D. L. Bourell ◽  
J. J. Beaman ◽  
Jr
Keyword(s):  
Solid Freeform Fabrication ◽  
Freeform Fabrication

scholarly journals Online Measurement of Deposit Surface in Electron Beam Freeform Fabrication

Sensors ◽  
2019 ◽  
Vol 19 (18) ◽  
pp. 4001 ◽  
Author(s):  
Shuhe Chang ◽  
Haoyu Zhang ◽  
Haiying Xu ◽  
Xinghua Sang ◽  
Li Wang ◽  
...  
Keyword(s):  
Electron Beam ◽  
3D Reconstruction ◽  
Three Dimensional ◽  
Thermal Conditions ◽  
Online Measurement ◽  
Three Dimensional Reconstruction ◽  
Continuous Change ◽  
Position Information ◽  
Freeform Fabrication ◽  
Dimensional Reconstruction

In the process of electron beam freeform fabrication (EBF3), due to the continuous change of thermal conditions and variability in wire feeding in the deposition process, geometric deviations are generated in the deposition of each layer. In order to prevent the layer-by-layer accumulation of the deviation, it is necessary to perform online geometry measurement for each deposition layer, based on which the error compensation can be done for the previous deposition layer in the next deposition layer. However, the traditional three-dimensional reconstruction method that employs structured laser cannot meet the requirements of long-term stable operation in the manufacturing process of EBF3. Therefore, this paper proposes a method to measure the deposit surfaces based on the position information of electron beam speckle, in which an electron beam is used to bombard the surface of the deposit to generate the speckle. Based on the structured information of the electron beam in the vacuum chamber, the three-dimensional reconstruction of the surface of the deposited parts is realized without need of additional structured laser sensor. In order to improve the detection accuracy, the detection error is theoretically analyzed and compensated. The absolute error after compensation is smaller than 0.1 mm, and the precision can reach 0.1%, which satisfies the requirements of 3D reconstruction of the deposited parts. An online measurement system is built for the surface of deposited parts in the process of electron beam freeform fabrication, which realizes the online 3D reconstruction of the surface of the deposited layer. In addition, in order to improve the detection stability of the whole system, the image processing algorithm suitable for this scene is designed. The reliability and speed of the algorithm are improved by ROI extraction, threshold segmentation, and expansion corrosion. In addition, the speckle size information can also reflect the thermal conditions of the surface of the deposited parts. Hence, it can be used for online detection of defects such as infusion and voids.

Distributed-Parameter Modeling for Geometry Control of Manufacturing Processes With Material Deposition

1998 ◽  
Vol 122 (1) ◽  
pp. 71-77 ◽  
Author(s):  
Charalabos Doumanidis ◽  
Eleni Skordeli
Keyword(s):  
Solid Freeform Fabrication ◽  
Surface Topology ◽  
Distributed Parameter ◽  
Surface Geometry ◽  
Mass Source ◽  
Freeform Fabrication ◽  
Geometry Model ◽  
Material Deposition ◽  
Solid Objects ◽  
3D Solid

Recent solid freeform fabrication methods generate 3D solid objects by material deposition in successive layers made of adjacent beads. Besides numerical simulation, this article introduces an analytical model of such material addition, using superposition of unit deposition distributions, composed of elementary spherical primitives consistent with the mass transfer physics. This real-time surface geometry model, with its parameters identified by in-process profile measurements, is used for Smith-prediction of the material shape in the unobservable deposition region. The model offers the basis for a distributed-parameter geometry control scheme to obtain a desired surface topology, by modulating the feed and motion of a moving mass source. The model was experimentally tested on a fused wire deposition welding station, using optical sensing by a scanning laser stripe. Its applications to other rapid prototyping methods are discussed. [S0022-0434(00)02301-7]

Solid Freeform Fabrication of Al-Li 2199 via Controlled-Short-Circuit-MIG Welding

2011 ◽  
Vol 409 ◽  
pp. 843-848
Author(s):  
David W. Heard ◽  
Julien Boselli ◽  
Raynald Gauvin ◽  
Mathieu Brochu
Keyword(s):  
Photoelectron Spectroscopy ◽  
Solid Freeform Fabrication ◽  
Short Circuit ◽  
Lithium Concentration ◽  
Gas Metal Arc Welding ◽  
Fusion Welding ◽  
Welding Parameters ◽  
Freeform Fabrication ◽  
Metal Arc Welding ◽  
Welding Processes

Aluminum-lithium (Al-Li) alloys are of interest to the aerospace and aeronautical industries as rising fuel costs and increasing environmental restrictions are promoting reductions in vehicle weight. However, Al-Li alloys suffer from several issues during fusion welding processes including solute segregation and depletion. Solid freeform fabrication (SFF) of materials is a repair or rapid prototyping process, in which the deposited feedstock is built-up via a layering process to the required geometry. Recent developments have led to the investigation of SFF processes via Gas Metal Arc Welding (GMAW) capable of producing functional metallic components. A SFF process via GMAW would be instrumental in reducing costs associated with the production and repair of Al-Li components. Furthermore the newly developed Controlled-Short-Circuit-MIG (CSC-MIG) process provides the ability to control the weld parameters with a high degree of accuracy, thus enabling the optimization of the solidification parameters required to avoid solute depletion and segregation within an Al-Li alloy. The objective of this study is to develop the welding parameters required to avoid lithium depletion and segregation. In the present study weldments were produced via CSC-MIG process, using Al-Li 2199 sheet samples as the filler material. The residual lithium concentration within the weldments was then determined via Atomic Absorption (AA) and X-ray Photoelectron Spectroscopy (XPS). The microstructure was analyzed using High Resolution Scanning Electron Microscopy (HR-SEM). Finally the mechanical properties of welded samples were determined through the application of hardness and tensile testing.

Sign in / Sign up

Export Citation Format

Share Document