scholarly journals A strategy to optimize the thermoelectric performance in a spark plasma sintering process

2016 ◽  
Vol 6 (1) ◽  
Author(s):  
Wan-Ting Chiu ◽  
Cheng-Lung Chen ◽  
Yang-Yuan Chen
Keyword(s):  
Spark Plasma Sintering ◽  
Thermoelectric Performance ◽  
Sintering Process ◽  
Plasma Sintering ◽  
Spark Plasma

Fabrication and Mechanical Properties of ultra fine WC-6wt.%Co by Spark Plasma Sintering Process

2011 ◽  
Vol 49 (01) ◽  
pp. 40-45 ◽  
Author(s):  
Hyun-Kuk Park ◽  
Seung-Min Lee ◽  
Hee-Jun Youn ◽  
Ki-Sang Bang ◽  
Ik-Hyun Oh
Keyword(s):  
Mechanical Properties ◽  
Spark Plasma Sintering ◽  
Sintering Process ◽  
Plasma Sintering ◽  
Spark Plasma

scholarly journals Processing of MMC through conventional sintering and spark plasma sintering process: A review

2020 ◽  
Vol 988 ◽  
pp. 012092
Author(s):  
B Stalin ◽  
M Ravichandran ◽  
M Balasubramanian ◽  
C Anand Chairman ◽  
D Pritima ◽  
...  
Keyword(s):  
Spark Plasma Sintering ◽  
Sintering Process ◽  
Plasma Sintering ◽  
Conventional Sintering ◽  
Spark Plasma

scholarly journals Shape Memory NiTi and NiTiCu Alloys Obtained by Spark Plasma Sintering Process

2015 ◽  
Vol 13 ◽  
pp. 83-90 ◽  
Author(s):  
Cristiana Diana Cristea ◽  
Magdalena Lungu ◽  
Alexander M. Balagurov ◽  
Virgil Marinescu ◽  
Otilia Culicov ◽  
...  
Keyword(s):  
Shape Memory ◽  
Intermetallic Compounds ◽  
Spark Plasma Sintering ◽  
Sintering Process ◽  
Transformation Behavior ◽  
Plasma Sintering ◽  
New Process ◽  
Shape Memory Properties ◽  
Spark Plasma ◽  
Niti Shape Memory Alloys

The addition of Cu to near equiatomic NiTi shape memory alloys (SMAs) can provide some modifications of their shape memory properties by affecting their transformation behavior. The same effect was obtained in the case of Ni3Ti2 and Ni4Ti3 precipitates presence in the microstructure of NiTi. Also the substitution of Cu to NiTi alloys increases the hardness of the materials. This paper presents the microstructural and mechanical investigations of NiTi and NiTiCu alloys obtained by spark plasma sintering (SPS) process that represents a great potential for researchers as a new process for the fabrication of intermetallic compounds.

scholarly journals Effects of Initial Punch-Die Clearance in Spark Plasma Sintering Process

2008 ◽  
Vol 49 (12) ◽  
pp. 2899-2906 ◽  
Author(s):  
Salvatore Grasso ◽  
Yoshio Sakka ◽  
Giovanni Maizza
Keyword(s):  
Spark Plasma Sintering ◽  
Sintering Process ◽  
Plasma Sintering ◽  
Spark Plasma

Preparation of In2O3-Sr2RuErO6 Composite Ceramics by the Spark Plasma Sintering and Their Thermoelectric Performance

2011 ◽  
Vol 27 (12) ◽  
pp. 1165-1168 ◽  
Author(s):  
Bo Cheng ◽  
Yuanhua Lin ◽  
Jinle Lan ◽  
Yong Liu ◽  
Cewen Nan
Keyword(s):  
Spark Plasma Sintering ◽  
Thermoelectric Performance ◽  
Composite Ceramics ◽  
Plasma Sintering ◽  
Spark Plasma

Development of WC-Fe3Al Composites by Spark Plasma Sintering Process

2016 ◽  
Vol 881 ◽  
pp. 307-312
Author(s):  
Luis Antonio C. Ybarra ◽  
Afonso Chimanski ◽  
Sergio Gama ◽  
Ricardo A.G. da Silva ◽  
Izabel Fernanda Machado ◽  
...  
Keyword(s):  
Spark Plasma Sintering ◽  
Zinc Stearate ◽  
Sintering Process ◽  
X Ray Diffraction ◽  
X Ray ◽  
Plasma Sintering ◽  
Al Composite ◽  
Spark Plasma ◽  
Short Time ◽  
Vibration Mill

Tungsten carbide (WC) based composites are usually produced with cobalt, but this binder has the inconvenience of shortage, unstable price and potential carcinogenicity. The objective of this study was to develop WC composite with intermetallic Fe3Al matrix. Powders of WC, iron and aluminum, with composition WC-10 wt% Fe3Al, and 0.5 wt% zinc stearate were milled in a vibration mill for 6 h and sintered in a SPS (spark plasma sintering) furnace at 1150 °C for 8 min under pressure of 30 MPa. Measured density and microstructure analysis showed that the composite had significant densification during the (low-temperature, short time) sintering, and X-ray diffraction analysis showed the formation of intermetallic Fe3Al. Analysis by Vickers indentation resulted in hardness of 11.2 GPa and fracture toughness of 24.6 MPa.m1/2, showing the feasibility of producing dense WC-Fe3Al composite with high mechanical properties using the SPS technique.

scholarly journals Sintering Process and Mechanical Properties of High-Si-Al Alloy Powder by Spark Plasma Sintering.

1997 ◽  
Vol 44 (10) ◽  
pp. 945-950 ◽  
Author(s):  
Takekazu Nagae ◽  
Masaru Yokota ◽  
Masateru Nose
Keyword(s):  
Mechanical Properties ◽  
Spark Plasma Sintering ◽  
Alloy Powder ◽  
Al Alloy ◽  
Sintering Process ◽  
Plasma Sintering ◽  
Spark Plasma

Densification mechanism of Ti-based metallic glass powders during spark plasma sintering process

2015 ◽  
Vol 66 ◽  
pp. 1-7 ◽  
Author(s):  
L.H. Liu ◽  
C. Yang ◽  
Y.G. Yao ◽  
F. Wang ◽  
W.W. Zhang ◽  
...  
Keyword(s):  
Metallic Glass ◽  
Spark Plasma Sintering ◽  
Sintering Process ◽  
Densification Mechanism ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Glass Powders
Sign in / Sign up

Export Citation Format

Share Document