Shear-Mode Rotary Magnetorheological Damper for Small-Scale Structural Control Experiments

2004 ◽  
Vol 130 (6) ◽  
pp. 904-911 ◽  
Author(s):  
Tim Tse ◽  
C. C. Chang
2007 ◽  
Vol 16 (3) ◽  
pp. 605-616 ◽  
Author(s):  
Fayçal Ikhouane ◽  
Shirley J Dyke

2014 ◽  
Vol 891-892 ◽  
pp. 1585-1590 ◽  
Author(s):  
Jana Horníková ◽  
Pavel Šandera ◽  
Stanislav Žák ◽  
Jaroslav Pokluda

Determination of fatigue crack growth characteristics under shear-mode loading is a rather complicated problem. To increase an efficiency and precision of such testing, special specimens enabling simultaneous propagation of shear cracks under II, III and II+III loading modes started to be used rather recently. K-calibration of these specimens was performed and, after unique pre-crack and heat-treatment procedures, effective thresholds in several metallic materials could be measured. However, a description of crack growth rate in terms of appropriate fracture mechanics quantities demands a precise assessment of plastic zone size under various shear-mode loading levels. This contribution is focused on the numerical elasto-plastic analysis of stress-strain field at the crack tip in specimens made of a pure polycrystalline (ARMCO) iron. The results reveal that the small scale yielding conditions are fulfilled in the near-threshold region. Starting from ΔK values approximately two times higher than the threshold, however, the ΔKJ or ΔJ approach should already be utilized. Probably the most interesting result of the analysis lies in a simple procedure that enables us to separate individual loading components ΔKJ,II and ΔKJ,III, applied in the mixed-mode II+III part of the specimen, by comparing elasto-plastic and elastic solutions.


2015 ◽  
Vol 751 ◽  
pp. 15-20 ◽  
Author(s):  
Stanislav Žák ◽  
Jana Horníková ◽  
Pavel Šandera ◽  
Jaroslav Pokluda

Determination of fatigue crack growth characteristics under shear-mode loading is a rather complicated problem. To increase an efficiency and precision of such testing, special specimens enabling simultaneous propagation of shear cracks under II, III and II+III loading modes started to be used rather recently. However, a description of crack growth rate in terms of appropriate fracture mechanics quantities demands a precise assessment of plastic zone size under various shear-mode loading levels. This contribution is focused on the numerical elasto-plastic analysis of stress-strain field at the crack tip in specimens made of a pure polycrystalline (ARMCO) iron loaded by mixed mode II+III. The dependence of plastic zone size on theJ-integral value described the wide region of loading. The results reveal that formixed mode II+III the small scale yielding conditions are fulfilled in the region where plastic zone size is smaller than 1/10 of the total crack length.


2015 ◽  
pp. 211-244
Author(s):  
Shaikh Faruque Ali ◽  
Ananth Ramaswamy

This chapter provides an introduction to semi active control of base isolated buildings using magnetorheological (MR) dampers. Recently developed nonlinear control algorithms are discussed. First a fuzzy logic control (FLC) is designed to decide how much voltage is required to be supplied to the MR damper for a desired structural response. The FLC is optimized using micro genetic algorithm. A novel geometric approach is developed to optimize the FLC rule base. Experiments are undertaken to access the efficacy of the optimal FLC. Secondly the chapter develops two model based control algorithms based on dynamic inversion and integrator backstepping approaches. A three storey base isolated building is used for experimental and numerical studies. A numerical comparison is shown with clipped optimal control.


2021 ◽  
Author(s):  
Gustavo Santiago ◽  
Alcides Pereira

<p>Inhalation of radon gas exposes the lungs to ionizing radiation which significantly contributes to the equivalent dose received by a human body. European Union advises Member States to identify radon prone areas (RPA), characterized by a significant percentage of dwellings above the national reference level (RL).</p><p>The presented work aims to evaluate the use of Receiver Operating Characteristic (ROC) curve analysis to map RPAs at a small-scale (from 1:25 000 to 1:1 000, henceforward called “regional” and “local” scale respectably), using interpolated surfaces of total gamma radiation (TGR) as proxy and point data of radon concentration in dwellings as the observed variable.</p><p>The case-study areas are in the center of Portugal (Tondela and Oliveira do Hospital) where outcrops different coarse-grained biotite granites (Beira’s Granite) and metasediments of Beiras’ Group, frequently as small enclaves hosted in the granites. An intense network of faults is also characteristic of these regions.</p><p>At Tondela area the geospatial analysis and ordinary kriging interpolation of TGR, on a regional scale, evidenced: a) a geological control on this variable; b) a structural control on anomalies by N35ºW orientated faults and by the intersection of these structures with others, namely N75ºE and N55ºE; c) and an anisotropic covariance of equally spaced points with N35<sup>o</sup>E oriented major axis. At Oliveira do Hospital, where at a regional scale just data of anomalies was available, the log-normal distribution of background values was simulated based on high-definition data obtained at a local scale. The results are consistent with the structural control pattern identified at Tondela. The best classifiers identified by the ROC analysis were 175 cps and 450 cps, respectably for Tondela and Oliveira do Hospital regions.</p><p>Establishing a 10% probability of dwellings with concentrations of radon above RL ( ) to define an RPA, all the areas were classified as RPAs. At Tondela region, the lowest risk area represents 25% probability of exceeding the RL and the highest risk area 52%. At Oliveira do Hospital almost the entire region represents 56% exceedance probability. The highest risk area is spatially related to intense anomalies and represent 78% exceedance probability.</p><p>For the geological context studied, the use of TGR proved to be suitable for radon gas risk mapping. The ROC curve analysis enabled to significantly classify higher and lower risk areas within high-risk regions, considering the small-scale variability. The ROC analysis did not produce a classifier properly calibrated to the RL but one that improves the cost-benefit of the classification relatively to the natural prevalence of the studied areas.</p>


Sign in / Sign up

Export Citation Format

Share Document