Stress–Strain Dependence of Cross-Linked Single-Phase Polyether Urethane

2014 ◽  
Vol 53 (4) ◽  
pp. 575-587 ◽  
Author(s):  
V. V. Tereshatov ◽  
V. Yu. Senichev
2012 ◽  
Vol 111 (4) ◽  
pp. 044906 ◽  
Author(s):  
S. Khansari ◽  
S. Sinha-Ray ◽  
A. L. Yarin ◽  
B. Pourdeyhimi

1962 ◽  
Vol 35 (4) ◽  
pp. 927-936
Author(s):  
P. Mason

Abstract In previous papers in this series the linear viscoelastic behavior of gum and filled rubbers has been studied at mean extensions up to 100%. Linearity was assured by allowing each specimen to relax at the required extension to its equilibrium state and then measuring the complex Young's modulus for very small strains superimposed upon this equilibrium extension. Analysis of the data was made either in terms of a Mooney strain-energy function or, more generally, by relation to the experimentally determined equilibrium stress-strain curve of the material. At much higher strains, however, the use of a strain-energy function is invalidated by the hysteretic behavior of the rubber, and the determination of a stress-strain curve at anything resembling equilibrium becomes increasingly difficult. Consequently, in the region of high strain it is preferable to examine the strain dependence of the viscoelasticity without involving a direct comparison with the equilibrium behavior. In principle, the most significant analysis would be obtained from a study of the strain dependence of the relaxation or retardation spectrum. The long-time end of the spectrum could perhaps be measured using a refined creep or stress relaxation technique, although considerable care would be required to separate the effects from the residual behavior resulting from the initial large elongation. In the rubber-glass transition region, with which this work is primarily concerned, the difficulty lies in making measurements over a sufficiently wide frequency range. Normally the Williams—Landel—Ferry (WLF) equation would be used to transform constant-frequency data from a wide temperature range to the equivalent isothermal spectrum over a wide frequency range; however, the validity of this equation has been confirmed only for amorphous polymers, and its application to highly stretched, anisotropic rubber involves several untested assumptions as discussed further below. The main object of the present paper is to describe the observed variations in the viscoelasticity of natural and butyl rubber over a wide range of extension and temperature, although, of necessity, over a limited range of frequency. In addition, a tentative indication of the influence of strain upon the relaxation spectra is given, and the implications of this are examined.


Author(s):  
Kazumune KATAGIRI ◽  
Koichi KASABA ◽  
Yoshitaka SHOJI ◽  
Masaki ISHIZAKI ◽  
Kazuo WATANABE ◽  
...  

A Taylor-type model for large deformation polycrystalline plasticity is formulated and evaluated by comparing the predictions for the evolution of crystallographic texture and the stress-strain response in simple compression and tension, plane strain compression, and simple shear of initially ‘isotropic’ OFHC copper against ( a ) corresponding experiments, and ( b ) finite element simulations of these experiments using a multitude of single crystals with accounting for the satisfaction of both compatibility and equilibrium. Our experiments and calculations show that the Taylor-type model is in reasonable first-order agreement with the experiments for the evolution of texture and the overall stress-strain response of single-phase copper. The results of the finite element calculations are in much better agreement with experiments, but at a substantially higher computational expense.


2018 ◽  
Vol 20 (2) ◽  
Author(s):  
Emilio Medrano ◽  
Mauro Quiroga ◽  
Felipe A. Reyes

After fabricating five metallographic specimens of the Cu0.95Al0.05 alloy from electrolytic copper and aluminum, these ones were both microstructurally characterized by using a metallographic optical microscope at room temperature and subjected to mechanical traction in order to chart the stress-strain curve. From the characterization, it has been found out that the Cu0.95Al0.05 microstructure is composed of a single phase, and from the tensile tests, it has been obtained its rupture point, 249.361 MPa. The obtained results were explained in the framework of the theory of metals and metal alloys.


Cryogenics ◽  
1999 ◽  
Vol 39 (5) ◽  
pp. 453-458 ◽  
Author(s):  
K Katagiri ◽  
K Kasaba ◽  
Y Shoji ◽  
M Ishizaki ◽  
K Watanabe ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document