Exergetic efficiency analysis of impingement jets integrated with internal conical ring roughened solar heat collector

2021 ◽  
pp. 1-21
Author(s):  
Anil Kumar ◽  
Nitin Kumar ◽  
Sunil Kumar ◽  
Rajesh Maithani
1975 ◽  
Author(s):  
R. GILLETTE ◽  
C. DEMINET ◽  
W. BEVERLY
Keyword(s):  

Author(s):  
Mohammad Salman ◽  
Ranchan Chauhan ◽  
Ganesh kumar Poongavanam ◽  
Myeong Hyun Park ◽  
Sung Chul Kim

1969 ◽  
Vol 47 (4) ◽  
pp. 226-235
Author(s):  
Allan L. Phillips

1. Modern coffee-processing facilities that have been developed recently have provided the features of low equipment costs and reduced labor requirements, but are somewhat expensive to operate when electric power is used entirely to heat the drying air. 2. The use of solar energy as a heat source was considered, since previous research where solar heat was used to dry other crops indicates that solar heat-collectors could also be used successfully for drying coffee. 3. An experimental processing facility which employs a solar heat-collector was built and operated, and it has been demonstrated that worthwhile reductions in operating costs can be achieved through the use of solar energy. 4. It was concluded that other coffee producers could economically use solar heat-collectors to reduce electricity costs. Drying facilities should be designed using the following as guides: A. Provide 10 square feet of drying-bin area for each 100 hundred-weights of coffee produced yearly. B. Install a fan which will deliver 100 c.f.m. per square foot of bin area against a static pressure of 1-inch water gage. C. Construct the solar heat-collector according to the specifications presented in figure 1. D. Install electric heating elements which provide up to 5,000 w. for each 100 hundred-weights processed yearly.


Energies ◽  
2020 ◽  
Vol 13 (4) ◽  
pp. 979 ◽  
Author(s):  
Caner Çuhac ◽  
Anne Mäkiranta ◽  
Petri Välisuo ◽  
Erkki Hiltunen ◽  
Mohammed Elmusrati

Solar heat, already captured by vast asphalt fields in urban areas, is potentially a huge energy resource. The vertical soil temperature profile, i.e., low enthalpy geothermal energy, reveals how efficiently the irradiation is absorbed or radiated back to the atmosphere. Measured solar irradiation, heat flux on the asphalt surface and temperature distribution over a range of depths describe the thermal energy from an asphalt surface down to 10 m depth. In this study, those variables were studied by long-term measurements in an open-air platform in Finland. To compensate the nighttime heat loss, the accumulated heat on the surface should be harvested during the sunny daytime periods. A cumulative heat flux over one year from asphalt to the ground was 70% of the cumulative solar irradiance measured during the same period. However, due to the nighttime heat losses, the net heat flux during 5 day period was only 18% of the irradiance in spring, and was negative during autumn, when the soil was cooling. These preliminary results indicate that certain adaptive heat transfer and storage mechanisms are needed to minimize the loss and turn the asphalt layer into an efficient solar heat collector connected with a seasonal storage system.


1975 ◽  
Author(s):  
D. E. Claridge ◽  
R. C. Langley ◽  
L. Muldawer ◽  
S. Schnatterly ◽  
S. D. Silverstein

Author(s):  
Yao-Hua Zhao ◽  
Fei-Long Zou ◽  
Yan-Hua Diao ◽  
Zhen-Hua Quan

The performance of a new flat plate solar heat collector with perfect combination of high efficiency and low cost is investigated experimentally. The new system described in this study uses a novel micro heat pipe array as a key component for the system. One such flat plate heat collector contains over 300 micro heat pipes per 1m2 and the hydraulic diameter of the micro heat pipes is 0.4–1.0mm. A detailed heat transfer experimental study is conducted during daylight hours over several months, focusing on the collector efficiency and overall efficiency of the system as well as total heat loss factor. The results show that the collector’s maximum instantaneous efficiency is up to 88%. Compared with conventional evacuated glass tube solar water heater, the system offers the additional benefits of high pressure resistance, low weight, good reliability and durability, easy integration into buildings and absence of freezing during winter months. Besides, compared with traditional flat-plate solar water system which is mainly sheet-and-tube concept, the system also shows many advantages: higher efficiency, much cheaper, absence of tube-bonding and freezing etc. Therefore, the system proposes a unique substitute to common solar water heating systems.


1987 ◽  
Vol 109 (4) ◽  
pp. 337-342 ◽  
Author(s):  
A. Suzuki ◽  
H. Okamura ◽  
I. Oshida

A linear model was developed to obtain the relationships between the characteristic temperatures of the solar heat collector (e.g., the fluid outlet temperature) and the heat capacitance rate of the heat transfer medium. Combining these relationships and the exergy concept, we derived the optimum operating conditions in a general form to satisfy the requirements for the optimum outlet temperature. The optimum operating conditions can be used as a criterion when an appropriate collector type must be chosen for any particular solar application system. To confirm the analytical results, experiments were carried out with a simple flat-plate type solar collector. Good agreement could be obtained between the theoretical values and the experimental results.


1969 ◽  
Vol 49 (4) ◽  
pp. 484-486
Author(s):  
Allan L. Phillips

EVALUATION OF "MYLAR" PLASTIC FILM AS A SURFACE FOR A SOLAR-HEAT COLLECTOR


Sign in / Sign up

Export Citation Format

Share Document