scholarly journals Study on turbulent flow in wave wall tube heat exchanger

2021 ◽  
Vol 2076 (1) ◽  
pp. 012025
Author(s):  
Liang Zhang ◽  
Anlong Zhang
Keyword(s):  
Heat Exchanger ◽  
Heat Exchange ◽  
Pressure Drop ◽  
Turbulent Flow ◽  
Average Pressure ◽  
Flow State ◽  
Tube Heat Exchanger ◽  
Exchange Performance ◽  
Straight Wall ◽  
Corrugated Structure

Abstract The traditional straight wall tube heat exchanger has low heat exchange efficiency, in order to solve this problem, the turbulent flow in wave wall tube heat exchanger was studied by numerical simulation. It is found that the unique corrugated structure of the heat exchange tube in the wave wall tube heat exchanger can improve the flow state of the fluid in the heat exchanger. The average pressure drop of heat exchanger gradually increases with the increase of Reynolds number Re. Under the same conditions, the average pressure drop of wave wall tube heat exchanger is lower than that of straight wall tube heat exchanger. The improvement of heat exchange performance of heat exchanger can not be realized only by increasing the inlet flow of heat exchanger. The wave wall tube heat exchanger can strengthen the heat exchange of the fluid in the heat exchanger.

Numerical simulation of the effect of baffle cut and baffle spacing on shell side heat exchanger performance using CFD

2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Swanand Gaikwad ◽  
Ashish Parmar
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Numerical Results ◽  
Shell Side ◽  
Tube Heat Exchanger ◽  
Shell And Tube ◽  
Two Parameters

AbstractHeat exchangers possess a significant role in energy transmission and energy generation in most industries. In this work, a three-dimensional simulation has been carried out of a shell and tube heat exchanger (STHX) consisting of segmental baffles. The investigation involves using the commercial code of ANSYS CFX, which incorporates the modeling, meshing, and usage of the Finite Element Method to yield numerical results. Much work is available in the literature regarding the effect of baffle cut and baffle spacing as two different entities, but some uncertainty pertains when we discuss the combination of these two parameters. This study aims to find an appropriate mix of baffle cut and baffle spacing for the efficient functioning of a shell and tube heat exchanger. Two parameters are tested: the baffle cuts at 30, 35, 40% of the shell-inside diameter, and the baffle spacing’s to fit 6,8,10 baffles within the heat exchanger. The numerical results showed the role of the studied parameters on the shell side heat transfer coefficient and the pressure drop in the shell and tube heat exchanger. The investigation shows an increase in the shell side heat transfer coefficient of 13.13% when going from 6 to 8 baffle configuration and a 23.10% acclivity for the change of six baffles to 10, for a specific baffle cut. Evidence also shows a rise in the pressure drop with an increase in the baffle spacing from the ranges of 44–46.79%, which can be controlled by managing the baffle cut provided.

A Method for Predicting Pressure Drop in a Shell-and-Tube Heat Exchanger with Roughened Tubes and a Smooth Shell Surface

1985 ◽  
Vol 6 (1) ◽  
pp. 26-30 ◽  
Author(s):  
O. M. BRAGINA ◽  
V. L. LELCHUK ◽  
A. G. SOROKIN ◽  
A. V. TURKIN ◽  
K. F. SHUISKAYA
Keyword(s):  
Heat Exchanger ◽  
Pressure Drop ◽  
Shell Surface ◽  
Smooth Shell ◽  
Tube Heat Exchanger ◽  
Shell And Tube

Experimental Investigation of Heat Transfer Enhancement of Shell and Tube Heat Exchanger Using SnO2-Water and Ag-Water Nanofluids

2019 ◽  
Vol 12 (4) ◽  
Author(s):  
S. V. Sridhar ◽  
R. Karuppasamy ◽  
G. D. Sivakumar
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Convective Heat Transfer Coefficient ◽  
Two Phase ◽  
Tube Heat Exchanger ◽  
Shell And Tube

Abstract In this investigation, the performance of the shell and tube heat exchanger operated with tin nanoparticles-water (SnO2-W) and silver nanoparticles-water (Ag-W) nanofluids was experimentally analyzed. SnO2-W and Ag-W nanofluids were prepared without any surface medication of nanoparticles. The effects of volume concentrations of nanoparticles on thermal conductivity, viscosity, heat transfer coefficient, fiction factor, Nusselt number, and pressure drop were analyzed. The results showed that thermal conductivity of nanofluids increased by 29% and 39% while adding 0.1 wt% of SnO2 and Ag nanoparticles, respectively, due to the unique intrinsic property of the nanoparticles. Further, the convective heat transfer coefficient was enhanced because of improvement of thermal conductivity of the two phase mixture and friction factor increased due to the increases of viscosity and density of nanofluids. Moreover, Ag nanofluid showed superior pressure drop compared to SnO2 nanofluid owing to the improvement of thermophysical properties of nanofluid.

Impact of an Anisotropic Fin Surface Design on the Thermal-Hydraulic Performance of a Plain-Fin-and-Tube Heat Exchanger

2011 ◽  
Author(s):  
Rong Yu ◽  
Andrew D. Sommers ◽  
Nicole C. Okamoto ◽  
Koushik Upadhyayula
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Heat Exchangers ◽  
Hydraulic Performance ◽  
Normal Operation ◽  
Surface Design ◽  
Tube Heat Exchanger ◽  
Silane Coating ◽  
Side Pressure

In this study, we have explored the effectiveness of heat exchangers constructed using anisotropic, micro-patterned aluminum fins to more completely drain the condensate that forms on the heat transfer surface during normal operation with the aim of improving the thermal-hydraulic performance of the heat exchanger. This study presents and critically evaluates the efficacy of full-scale heat exchangers constructed from these micro-grooved surfaces by measuring dry/wet air-side pressure drop and dry/wet air-side heat transfer data. The new fin surface design was shown to decrease the core pressure drop of the heat exchanger during wet operation from 9.3% to 52.7%. Furthermore, these prototype fin surfaces were shown to have a negligible effect on the heat transfer coefficient under both dry and wet conditions while at the same time reducing the wet airside pressure drop thereby decreasing fan power consumption. That is to say, this novel fin surface design has shown the ability, through improved condensate management, to enhance the thermal-hydraulic performance of plain-fin-and-tube heat exchangers used in air-conditioning applications. This paper also presents data pertaining to the durability of the alkyl silane coating.

Sign in / Sign up

Export Citation Format

Share Document