SWPS ECO Bricks: Development of Sustainable Brick Utilising Solid Waste Fly Ash and Paint Sludge

This mini-review article summarizes the available technologies for the recycling of heavy metals (HMs) in municipal solid waste incineration (MSWI) fly ash (FA). Recovery technologies included thermal separation (TS), chemical extraction (CE), bioleaching, and electrochemical processes. The reaction conditions of various methods, the efficiency of recovering HMs from MSWI FA and the difficulties and solutions in the process of technical development were studied. Evaluation of each process has also been done to determine the best HM recycling method and future challenges. Results showed that while bioleaching had minimal environmental impact, the process was time-consuming. TS and CE were the most mature technologies, but the former process was not cost-effective. Overall, it has the greatest economic potential to recover metals by CE with scrubber liquid produced by a wet air pollution control system. An electrochemical process or solvent extraction could then be applied to recover HMs from the enriched leachate. Ongoing development of TS and bioleaching technologies could reduce the treatment cost or time.

Download Full-text

Ternary Mixes of Self-Compacting Concrete with Fly Ash and Municipal Solid Waste Incinerator Bottom Ash

Applied Sciences ◽

10.3390/app11010107 ◽

2020 ◽

Vol 11 (1) ◽

pp. 107

Author(s):

B. Simões ◽

P. R. da Silva ◽

R. V. Silva ◽

Y. Avila ◽

J. A. Forero

Keyword(s):

Fly Ash ◽

Municipal Solid Waste ◽

Solid Waste ◽

Bottom Ash ◽

Chloride Diffusion ◽

Waste Incinerator ◽

Chloride Diffusion Coefficient ◽

Municipal Solid Waste Incinerator ◽

Self Compacting Concrete ◽

Solid Waste Incinerator

This study aims to evaluate the potential of incorporating fly ash (FA) and municipal solid waste incinerator bottom ash (MIBA) as a partial substitute of cement in the production of self-compacting concrete mixes through an experimental campaign in which four replacement levels (i.e., 10% FA + 20% MIBA, 20% FA + 10% MIBA, 20% FA + 40% MIBA and 40% FA + 20% MIBA, apart from the reference concrete) were considered. Compressive and tensile strengths, Young’s modulus, ultra-sonic pulse velocity, shrinkage, water absorption by immersion, chloride diffusion coefficient and electrical resistivity were evaluated for all concrete mixes. The results showed a considerable decline in both mechanical and durability-related performances of self-compacting concrete with 60% of substitution by MIBA mainly due to the aluminium corrosion chemical reaction. However, workability properties were not significantly affected, exhibiting values similar to those of the control mix.

Download Full-text

An Experimental Study on the Melting Solidification of Municipal Solid Waste Incineration Fly Ash

Sustainability ◽

10.3390/su13020535 ◽

2021 ◽

Vol 13 (2) ◽

pp. 535

Author(s):

Jing Gao ◽

Tao Wang ◽

Jie Zhao ◽

Xiaoying Hu ◽

Changqing Dong

Keyword(s):

Heavy Metals ◽

High Temperature ◽

Fly Ash ◽

Municipal Solid Waste ◽

Solid Waste ◽

Liquid Slag ◽

Melting Process ◽

Waste Incineration ◽

Municipal Solid Waste Incineration ◽

Mswi Fly Ash

Melting solidification experiments of municipal solid waste incineration (MSWI) fly ash were carried out in a high-temperature tube furnace device. An ash fusion temperature (AFT) test, atomic absorption spectroscopy (AAS), scanning electron microscope (SEM), and X-ray diffraction (XRD) were applied in order to gain insight into the ash fusibility, the transformation during the melting process, and the leaching behavior of heavy metals in slag. The results showed that oxide minerals transformed into gehlenite as temperature increased. When the temperature increased to 1300 °C, 89 °C higher than the flow temperature (FT), all of the crystals transformed into molten slag. When the heating temperatures were higher than the FT, the volatilization of the Pb, Cd, Zn, and Cu decreased, which may have been influenced by the formation of liquid slag. In addition, the formation of liquid slag at a high temperature also improved the stability of heavy metals in heated slag.

Download Full-text