scholarly journals Empirical relationship for drilling rate in hard rock underground mines

2021 ◽  
Vol 833 (1) ◽  
pp. 012135
Author(s):  
A C Adoko ◽  
D Moesi ◽  
A S Sharipov
2020 ◽  
Vol 2020 ◽  
pp. 1-13 ◽  
Author(s):  
Yohan Cha ◽  
Tae-Min Oh ◽  
Gye-Chun Cho

Abrasive waterjets are being increasingly used in civil engineering for rock and concrete cutting, particularly for the demolition or repair of old structures. The energy of an abrasive waterjet is primarily provided by the accelerated abrasive. The momentum transfer during mixing and acceleration determines the abrasive velocity, which affects the cutting performance. Meanwhile, the geometry of the focus at which mixing occurs influences the momentum transfer efficiency. In this study, the effects of the focus geometry on the optimum abrasive flow rate (AFR) and momentum transfer characteristics in hard rock cutting were investigated. Experiments were conducted using granite specimens to test the AFR under different focus geometry conditions such as diameter and length. The results show that the focus geometry significantly affects the maximum cutting depth and optimum AFR. The maximum cutting energy was analyzed based on the cutting efficiency of a single abrasive particle. In addition, the momentum transfer parameter (MTP) was evaluated from the empirical relationship between the maximum energy and the cutting depth for granitic rocks. Accordingly, a model for estimating the MTP based on the AFR was developed. It is expected that the results of this study can be employed for the optimization of waterjet rock cutting.


Energies ◽  
2018 ◽  
Vol 11 (7) ◽  
pp. 1901 ◽  
Author(s):  
Kashi Jessu ◽  
Anthony Spearing ◽  
Mostafa Sharifzadeh

Pillar stability is an important factor for safe working and from an economic standpoint in underground mines. This paper discusses the effect of blast damage on the strength of hard rock pillars using numerical models through a parametric study. The results indicate that blast damage has a significant impact on the strength of pillars with larger width-to-height (W/H) ratios. The blast damage causes softening of the rock at the pillar boundaries leading to the yielding of the pillars in brittle fashion beyond the blast damage zones. The models show that the decrease in pillar strength as a consequence of blasting is inversely correlated with increasing pillar height at a constant W/H ratio. Inclined pillars are less susceptible to blast damage, and the damage on the inclined sides has a greater impact on pillar strength than on the normal sides. A methodology to analyze the blast damage on hard rock pillars using FLAC3D is presented herein.


2020 ◽  
Vol 53 (6) ◽  
pp. 2789-2804 ◽  
Author(s):  
Xu Ma ◽  
Erik Westman ◽  
Dave Counter ◽  
Farid Malek ◽  
Brent Slaker

AbstractThis work aims to examine the stress redistribution with evolving seismicity rates using a passive seismic tomographic tool. We compiled a total of 26,000 events from two underground mines and partitioned them into multiple clusters in a temporal sequence, each of which contains 1000 events. To image stress redistribution associated with seismicity rates, we then run the tomographic studies using each cluster to yield seismic tomograms and computed the corresponding seismicity rate. We found that high velocity anomalies grew with the increase of seismicity rates, and they switched to a shrinking tendency under low seismicity rates. Results of this study imply that seismicity rates increase with increasing stress concentration and decrease with decreasing stress concentration. This study highlights the value of utilizing passive seismic tomography for estimating stress evolution associated with the change of seismicity rates at underground mines. Our findings illuminate the applications of using mining-induced seismicity to assess stress redistribution associated with seismicity rates at hard-rock mines, providing insights into seismic hazards for deep mining.


2020 ◽  
pp. 34-42
Author(s):  
Thibault Chastel ◽  
Kevin Botten ◽  
Nathalie Durand ◽  
Nicole Goutal

Seagrass meadows are essential for protection of coastal erosion by damping wave and stabilizing the seabed. Seagrass are considered as a source of water resistance which modifies strongly the wave dynamics. As a part of EDF R & D seagrass restoration project in the Berre lagoon, we quantify the wave attenuation due to artificial vegetation distributed in a flume. Experiments have been conducted at Saint-Venant Hydraulics Laboratory wave flume (Chatou, France). We measure the wave damping with 13 resistive waves gauges along a distance L = 22.5 m for the “low” density and L = 12.15 m for the “high” density of vegetation mimics. A JONSWAP spectrum is used for the generation of irregular waves with significant wave height Hs ranging from 0.10 to 0.23 m and peak period Tp ranging from 1 to 3 s. Artificial vegetation is a model of Posidonia oceanica seagrass species represented by slightly flexible polypropylene shoots with 8 artificial leaves of 0.28 and 0.16 m height. Different hydrodynamics conditions (Hs, Tp, water depth hw) and geometrical parameters (submergence ratio α, shoot density N) have been tested to see their influence on wave attenuation. For a high submergence ratio (typically 0.7), the wave attenuation can reach 67% of the incident wave height whereas for a low submergence ratio (< 0.2) the wave attenuation is negligible. From each experiment, a bulk drag coefficient has been extracted following the energy dissipation model for irregular non-breaking waves developed by Mendez and Losada (2004). This model, based on the assumption that the energy loss over the species meadow is essentially due to the drag force, takes into account both wave and vegetation parameter. Finally, we found an empirical relationship for Cd depending on 2 dimensionless parameters: the Reynolds and Keulegan-Carpenter numbers. These relationships are compared with other similar studies.


Sign in / Sign up

Export Citation Format

Share Document