scholarly journals Use of factors of photoperiod duration and growth regulators to increase the yield of mixoploid plants in C0 generation in meadow clover (Trifolium pratense L.)

2021 ◽  
Vol 901 (1) ◽  
pp. 012024
Author(s):  
M Yu Novoselov ◽  
L V Drobysheva ◽  
O A Starshinova

Abstract It has been established that the studied mode of cultivation of meadow clover under controlled environmental conditions, with continuous illumination with an intensity of 18-20 thousand lux and a constant temperature of + 25 °C, causes significant morphological changes in meadow clover. Compared with the optimal (control), the proposed growing regime halves the development time of plants and by the same amount reduces the severity of morphological traits, while simultaneously causing apical dominance in 54% of plants. Spraying plants with phytohormone in the form of naphthylacetic acid in all studied concentrations reduced the growing season by 4-8 days and increased pollen fertility by 8-10%. The optimal concentration of naphthylacetic acid (NLA) was revealed to suppress the growth of secondary meristems in meadow clover under the conditions of an experimental plant growing regime. The most significant effect on the manifestation of apical dominance was shown by the use of naphthylacetic acid at a concentration of 0.001%. The combined use of the proposed growing regime and treatment with naphthylacetic acid at a concentration of 0.001% increased the yield of plants with apical dominance from 54.5% to 76%. The developed method has shown high efficiency for the creation of tetraploid forms of meadow clover. When growing clover C0 generation and selection of mixoploid plants, the yield of mixoploids increased 5.4 times, the survival rate of seedlings increased by 21%, the time to obtain one generation and the selection of mixoploids decreased by 58%.

Crop Science ◽  
1965 ◽  
Vol 5 (5) ◽  
pp. 425-428 ◽  
Author(s):  
R. J. Bula ◽  
R. G. May ◽  
C. S. Garrison ◽  
C. M. Rincker ◽  
J. G. Dean

2009 ◽  
Vol 4 (6) ◽  
pp. 1934578X0900400 ◽  
Author(s):  
Aldo Tava ◽  
Daniele Ramella ◽  
Maris Grecchi ◽  
Paolo Aceto ◽  
Renato Paoletti ◽  
...  

The composition of the volatile fraction of two important forage legumes from Italian sub-alpine N.E. pastureland, namely Trifolium pratense L. subsp. pratense (red clover) and T. repens subsp. repens (white clover) were investigated. The volatile oil was obtained from the fresh aerial parts by steam distillation and analyzed by GC/FID and GC/MS. The oil yield was 0.018 and 0.021% (weight/fresh weight basis) for T. pratense and T. repens, respectively. Several classes of compounds were found in both the oils, including alcohols, aldehydes, ketones, terpenes, esters, hydrocarbons, phenolics and acids. Qualitative and quantitative differences were found.


Crop Science ◽  
1968 ◽  
Vol 8 (4) ◽  
pp. 451-454 ◽  
Author(s):  
Norman L. Taylor ◽  
W. A. Kendall ◽  
W. H. Stroube

Author(s):  
Andre D. L. Batako ◽  
Valery V. Kuzin ◽  
Brian Rowe

High Efficiency Deep Grinding (HEDG) has been known to secure high removal rates in grinding processes at high wheel speed, relatively large depth of cut and moderately high work speed. High removal rates in HEDG are associated with very efficient grinding and secure very low specific energy comparable to conventional cutting processes. Though there exist HEDG-enabled machine tools, the wide spread of HEDG has been very limited due to the requirement for the machine tool and process design to ensure workpiece surface integrity. HEDG is an aggressive machining process that requires an adequate selection of grinding parameters in order to be successful within a given machine tool and workpiece configuration. This paper presents progress made in the development of a specialised HEDG machine. Results of HEDG processes obtained from the designed machine tool are presented to illustrate achievable high specific removal rates. Specific grinding energies are shown alongside with measured contact arc temperatures. An enhanced single-pole thermocouple technique was used to measure the actual contact temperatures in deep cutting. The performance of conventional wheels is depicted together with the performance of a CBN wheel obtained from actual industrial tests.


2011 ◽  
Vol 109 ◽  
pp. 400-404
Author(s):  
Yan Hong Yang ◽  
Da Fu Ni

Performance and working principle of high-efficiency multi-cyclone were analyzed, and the structural design shortage of original high-efficiency multi-cyclone was pointed out. Its structure was researched and designed, including determination of setting chamber and pipe number, selection of material and the design of cyclones.


Sign in / Sign up

Export Citation Format

Share Document