scholarly journals Influence of Ni addition on Abrasive wear behaviour of plasma-sprayed Duplex stainless steel coatings

2021 ◽  
Vol 1166 (1) ◽  
pp. 012056
Author(s):  
E Edward Anand ◽  
K Balasubramanian
Keyword(s):  
Stainless Steel ◽  
Abrasive Wear ◽  
Duplex Stainless Steel ◽  
Wear Behaviour ◽  
Ni Addition ◽  
Abrasive Wear Behaviour ◽  
Plasma Sprayed ◽  
Stainless Steel Coatings

Determination of Abrasive Wear Resistance of Plasma Sprayed Coatings on Stainless Steel Substrate

2015 ◽  
Vol 766-767 ◽  
pp. 579-584 ◽  
Author(s):  
A. Anderson
Keyword(s):  
Stainless Steel ◽  
Wear Resistance ◽  
Abrasive Wear ◽  
Steel Substrate ◽  
Ceramic Coatings ◽  
Atmospheric Plasma ◽  
Wear Behaviour ◽  
Coating Materials ◽  
Plasma Sprayed Coatings ◽  
Plasma Sprayed

A relative study among various types of coating materials to develop wear resistance of stainless steel has been performed. Ceramic coatings with the thickness up to 250 μm were prepared by Atmospheric plasma spray technique on the stainless steel. Two different types of coating materials such that Yttria Stabilised Zirconia, Zirconia Ceria powder were used. The influence of Ceria powder on abrasive wear was determined. It was found that the addition of Ceria to Yttria Stabilised Zirconia in a sufficient amount helped in increasing its wear resistance compared to the wear behaviour of pure Yttria Stabilised Zirconia powder. Moreover, it was found that the lesser the surface roughness of the coating layer,.

scholarly journals MICRO-ABRASIVE WEAR BEHAVIOUR OF LOW-TEMPERATURE PLASMA CARBURIZED AISI 420 MARTENSITIC STAINLESS STEEL

2017 ◽  
Author(s):  
Cristiano José Scheuer ◽  
Rodrigo Perito Cardoso ◽  
Júlio César Klein das Neves ◽  
Sílvio Francisco Brunatto
Keyword(s):  
Stainless Steel ◽  
Low Temperature ◽  
Abrasive Wear ◽  
Martensitic Stainless Steel ◽  
Wear Behaviour ◽  
Low Temperature Plasma ◽  
Temperature Plasma ◽  
Aisi 420 ◽  
Abrasive Wear Behaviour

scholarly journals Abrasive Wear Behaviour of Plasma Sprayed Al2O3 / TiO2 Coatings

2019 ◽  
Vol 9 (2) ◽  
pp. 5020-5023
Keyword(s):  
Abrasive Wear ◽  
Wear Behaviour ◽  
High Wear Resistance ◽  
Homogeneous Distribution ◽  
Premature Failure ◽  
Wear Rates ◽  
Spray Coatings ◽  
Abrasive Wear Behaviour ◽  
Plasma Sprayed ◽  
Cylinder Bore

Premature failure due to abrasive wear is observed in high powered engine in recent decades, despite of stringent maintenance procedures comparative to older engine. Plasma spray coatings are recurrently used to circumvent the abrasive wear in aerospace, defense and certain automotive applications like piston pump, cylinder bore etc. This work is to identify the most influencing wear parameters namely sliding speed (SS), applied load (AL) and sliding distance (SD) of the composite coated steel. Initially the surface morphology and elemental analysis was carried out to analyze the surface roughness and homogeneous distribution of the composites. Furthermore wear analyzes results indicates that the composite coating has high wear resistance and specific wear rates are ranging from 0.52346 × 10-5 m 3 / N-m to 3.25711× 10-5 m 3 / N-m

Effect of oxidation on abrasive wear behaviour of titanium carbide based composites in silica medium

2010 ◽  
Vol 16 (4) ◽  
pp. 264 ◽  
Author(s):  
M Antonov ◽  
I Hussainova ◽  
J Pirso ◽  
K Juhani ◽  
M Viljus
Keyword(s):  
Titanium Carbide ◽  
Abrasive Wear ◽  
Wear Behaviour ◽  
Abrasive Wear Behaviour
Sign in / Sign up

Export Citation Format

Share Document